Mtd Pro Lawn Mower Parts

Mower won't start or cuts out during use? A faulty ignition coil prevents spark to the engine. This part restores reliable starting in 30-45 minutes.

This is a genuine replacement ignition key that is manufactured by MTD for use in select models of outdoor power equipment. The ignition key is a plastic piece that is inserted into the ignition cylinder to start the machine. Turning the plastic key will signal to the engine to fire. This is a durable plastic piece, but it can become damaged or lost over time, which will render the machine unable to start. Replacing it will be necessary in order to operate the unit. This genuine OEM ignition key is manufactured to exact standards. It can be used in snowblowers and snow throwers from MTD, Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. The durable plastic key is sold as an individual unit and does not require any tools for installation. This is a simple replacement that should only take a couple of minutes. In the event that the old key is damaged or stuck in the ignition, it may take more effort. It is important to disconnect the power supply for safety before performing any repairs, as well as to wear gloves for hand protection.

External gasket kit seals carburetor and engine surfaces on lawn equipment. Replace when you notice fuel leaks or loss of compression. Verify fit with your model.

Snowblower won't start or pulls hard? This recoil starter assembly restores reliable pull-start function. Common repair for worn or broken recoil.

Oil fill plug assembly for small engines. Seals the oil fill opening to prevent leaks. Replace if cracked, stripped, or missing to maintain proper seal.

Plastic primer bulb that draws fuel into the carburetor when pressed. Replace if cracked, broken, or no longer creating proper seal for priming.

This small tension spring connects to the governor arm on the engine, helping regulate engine speed under varying load conditions. It ensures the throttle responds properly to maintain consistent RPMs. Replace this spring if your engine surges, runs erratically, or fails to maintain a steady speed during operation.

Fuel filters are created to strain out gas before it reaches the carburetor in lawnmowers and other gardening tools. Located in the fuel line or the fuel tank, it prevents unwanted debris from reaching the carburetor, which can cause engine damage. If the fuel filter is damaged or becomes clogged with material, it no longer offers the same protection to the carburetor. This can lead to difficulty starting the lawnmower and decreased performance. Correcting this issue early can prevent damage that might require a new lawnmower. Maintenance of the lawnmower by adding fuel stabilizer, changing the oil, and replacing the air filter will increase the life of lawn care equioment. Even if no issues are present, the fuel filter should be replaced after about 200 hours of use. Disconnecting the spark plug should be done prior to installing a new fuel filter. This fuel filter is a genuine OEM component directly from the manufacturer and comes as an individual part. It can be used with various Craftsman, Cub Cadet, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and Mastercut lawnmowers, tillers, blowers, and wood chippers.

This is a complete carburetor assembly for a lawn and garden equipment engine. The carburetor mixes air and fuel in the correct ratio for combustion, enabling the engine to run smoothly. Replace this carburetor if the engine is hard to start, surges, stalls, runs rough, or if fuel is leaking from the carburetor body.

Drive belt manages your mower's speed and propulsion system. Replace if worn, cracked, or slipping. Confirm fit with your model number before ordering.

Drive belt for lawn tractors, transfers power to operate mower components. Replace when worn, cracked, or slipping. Verify fit with your model number.

Drive belt for lawn tractor transmission systems. Replace if you notice slipping, squealing, or loss of power. Verify fit with your model number.

This is a V-groove drive pulley with an integrated hub designed for the transmission system of a lawn tractor. It transfers rotational power from the engine via the drive belt to the transmission. Replace this pulley if it is wobbling, cracked, or worn, which can cause belt slipping, loss of drive power, or unusual noises during operation.

Replacement seat for lawn tractors and riding mowers. Installs on the operator platform. Needed when original seat is cracked, torn, or broken.

Snow not throwing or auger jammed? This 21-inch auger assembly restores snow clearing performance. Moderate DIY install with basic hand tools.

Mulch plug assembly for walk-behind mowers. Blocks the discharge chute opening to enable mulching mode. Replace if cracked, broken, or missing.