Mtd Snow Removal Equipment Parts

There are multiple uses for the 5/16-18 Hex Screw. It is often used with small gasoline-powered yard equipment such as lawn and garden machines. While hex screws such as these may be used in edgers and snowblowers, the most frequent use this screw is in yard tractors. This variety of screw is commonly used in attaching the various appendages of gas-powered equipment to a central operating platform. In particular, these hex screws are used to secure the engine block of power tools to the frame or housing of the equipment. Once in place, these fasteners have an almost unbreakable strength to them. This is so much so the case that often, in order to detach the engine manifold and repair the inner workings of an engine, the bolts must be chiseled or cut loose. In such cases, it is necessary for the bolts to be replaced during reassembly. Manufacturers insist that genuine OEM replacement parts be used in the rebuilding process. These replacement parts were manufactured to the same exacting specifications used to make the original screws. These OEM screws are compatible with equipment made and sold by Yard-Man, Cub Cadet, Troy-Bilt, Husky, MTD, Bolens, and Yard Machines.

Split pin fastener for lawn tractors and outdoor power equipment. Secures axles, linkages, and moving parts. Replace when bent, missing, or corroded.

This is a dual cable fitting, designed to work with snowblowers. The cable fitting holds the auger cable in place, ensuring that it does not become a safety issue. The cable simply runs through the fitting, and the part holds it in place. Cable fittings are made from durable plastic and are not moving parts. However, they can suffer damage in several different ways. Plastic becomes brittle over time and through exposure to the elements, and the fitting may eventually crack and break. It is also possible to damage the fitting through contact with a hard surface while using the snowblower. Replacing a dual cable fitting is not difficult, although it will require a socket set. Locate the fitting on the handle of the snowblower and remove the mounting bolt(s). Remove the fitting and replace it with the new one. Be careful that the cables are properly routed inside the new fitting, then replace the mounting bolt(s). This is a genuine OEM part, and it is sold individually. This dual cable fitting is compatible with Craftsman, MTD, and Yard Machine snow blowers.

Extension spring that mounts the drive plate assembly to the housing frame on snowblowers. Replace if broken, stretched, or missing for secure mounting.

30-inch shave plate blade for snow throwers. Installs at the auger housing base to protect surfaces. Replace when worn, cracked, or damaged.

Seals the fuel bowl to prevent leaks and keep dirt out of your fuel system. Replace when cracked or leaking. Confirm fit with your model number.

Pivot rod for gas snow throwers. Connects control lever to moving components. Replace if bent, broken, or worn to restore proper mechanical operation.

Protective slide shoe that mounts to the snowblower housing base. Maintains clearance to prevent surface damage. Replace if cracked, worn down, or missing.

This is a shoulder screw that is used to secure the handles of yard equipment. Typically, this screw is used with a matching wing nut, which is sold separately. Many different varieties of push lawn mowers have handles that fold downward for ease of storage. This is one of the locations on a mower where one will find shoulder bolts and the point at which these bolts are most likely wear out. While they are made of durable machined metal, shoulder bolts receive a great deal of wear, particularly from the handles being raised and lowered each time the mower is used. When pushing down on the mower to clear wet grass clippings or to make sharp turns with the mower, the entire weight of the mower is put on the two shoulder screws where they intersect. Since the metal of the handles can turn at that juncture, extra shearing action is put on the shoulder bolts, which can wear out. It is actually advantageous that the bolts wear out since otherwise, the handles themselves would warp and break apart. These OEM genuine replacement parts fit a number of different lawn and garden machines, including many made by Cub Cadets, Husky, Troy-Bilt, Craftsman, Yard-Man, Bolens, MTD, and Yard-Machines.

Flange bushing for snow throwers and lawn equipment. Replace when worn to maintain smooth operation and prevent part damage. Verify fit with your model.

This control handle is designed specifically as a replacement for use on select walk-behind lawn mowers. The control handle is the safety that is engaged to allow the engine to run. When holding the control handle in, the pull start can be activated and the engine will run. Once the control handle is released, the engine will stop. In the event that the control handle becomes damaged or fails, it will need to be replaced so that the mower can continue to be used. This handle can provide a genuine replacement for compatible models. This control handle is manufactured to exact standards by MTD and provides an exact fit. It is compatible with hundreds of models, including select models from RYOBI, Yard Machines, Troy-Bilt, Yard-Man, Husky, Bolens, and Cub Cadet. This part is also known as the control bar, control handle, engine stop handle, bail control, or mower bail. It is made of durable metal and sold individually. No tools are required for the installation of this part. To replace the handle, simply squeeze the existing control handle to remove it from the outer handle, and then align the new handle and slide it into place. When properly installed, the pressure will hold it in place and allow for proper operation.

This part is an idler pulley. The idler pulley applies tension to and guides the engine drive belt. A wrench set is needed to perform any repair involving the idler pulley part.The idler pulley can become worn over time with normal use. Wear to the pulley can cause the belt to slip. Signs that the idler pulley needs to be replaced include squealing noises coming from the equipment, the engine stalling, or overheating. The idler pulley is an essential component and it is important to replace this part if it becomes worn, broken, or damaged in any way.This part is a genuine MTD part and is an OEM part sourced directly from the manufacturer and it is sold individually. This idler pulley is compatible with lawn tractors and snowblowers manufactured by MTD, Yard Machines, Bolens, Yard-Man, Troy-Bilt, Cub Cadet, and Husky.

If your lawn tractor won't stop properly or brakes feel weak, this brake puck creates pressure on the brake disk when you push the pedal. Essential safety part.

Drive belt connects engine to transmission on gas snowblowers. Replace when worn, cracked, or slipping to restore forward motion. Verify fit with model number.

Cogged rubber belt that rotates the augers in your snowblower. Replace when stretched, cracked, or slipping. Verify fit with your model number.

Right-side wheel assembly with tire and rim for gas snowblowers. Replaces cracked, damaged, or worn wheels for proper traction and maneuverability.