Mtd Snow Removal Equipment Parts

Snow blower won't move forward or loses traction? A worn friction wheel is usually the culprit. This rubber disc contacts the drive wheel to propel your machine.

Speed select cable for snowblower ground drive system. Replace if your cable is deteriorated, damaged, detached, or missing from the control assembly.

This is a genuine MTD fuel cap replacement made for use on select snowblowers. It features a molded gasket for secure sealing and less risk of losing parts. The fuel cap is responsible for securing the fuel in the fuel tank during operation so that it doesn't spill out. There is an air hole in the cap to prevent pressurization of the fuel, ensuring safe operation at all times. This cap is made of plastic and it can become cracked or stripped with regular use. If it is damaged, the fuel will not be secure and the machine will not be safe to use. That will require an immediate replacement. This OEM fuel cap is made to exact standards by MTD and is compatible with several models of snow blowers and snow throwers. It is also capable of fitting select models from Yard Machines, Troy-Bilt, Cub Cadet, Yard-Man, and Husky. It features an easy plastic grip and a seal to prevent spillage. It can be installed with no tools and is sold as an individual unit. It is easy to screw the new cap into place, but be sure to thread the screw properly to prevent accidental stripping or misthreading that can cause the cap to get stuck.

There are multiple uses for the 5/16-18 Hex Screw. It is often used with small gasoline-powered yard equipment such as lawn and garden machines. While hex screws such as these may be used in edgers and snowblowers, the most frequent use this screw is in yard tractors. This variety of screw is commonly used in attaching the various appendages of gas-powered equipment to a central operating platform. In particular, these hex screws are used to secure the engine block of power tools to the frame or housing of the equipment. Once in place, these fasteners have an almost unbreakable strength to them. This is so much so the case that often, in order to detach the engine manifold and repair the inner workings of an engine, the bolts must be chiseled or cut loose. In such cases, it is necessary for the bolts to be replaced during reassembly. Manufacturers insist that genuine OEM replacement parts be used in the rebuilding process. These replacement parts were manufactured to the same exacting specifications used to make the original screws. These OEM screws are compatible with equipment made and sold by Yard-Man, Cub Cadet, Troy-Bilt, Husky, MTD, Bolens, and Yard Machines.

Hex screw fastener for securing lawn mower components. Replace if stripped, rusted, or missing to ensure proper assembly and equipment stability.

Fix a chute that won't rotate properly with this snow thrower chute flange keeper latch. Secures the flange to ensure smooth chute rotation. Easy DIY fix.

This lower chute is a quality replacement part that is used on several models of snowblowers. It is made of high-quality plastic for durability and is placed so it can direct snow in a certain direction when it leaves a snowblower. Over time and with regular use, this part can become damaged. If this occurs, it will need to be replaced so the discharged snow ends up in the right location.When replacing the lower chute, a wrench and work gloves will be needed. The snowblower should be placed on a flat surface, and the spark plug wire needs to be disconnected. The gearbox and the lower chute will need to be removed before the new replacement part can be installed. Line up the chute and install it used the cotter pin and flange lock nut. Replace all the components before using the snowblower.This is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold on an individual basis. The lower chute is used with snowblowers manufactured by Craftsman, Cub Cadet, Huskee, MTD, Troy-Bilt, Yard Machines, and Yard-Man.

This control handle is designed specifically as a replacement for use on select walk-behind lawn mowers. The control handle is the safety that is engaged to allow the engine to run. When holding the control handle in, the pull start can be activated and the engine will run. Once the control handle is released, the engine will stop. In the event that the control handle becomes damaged or fails, it will need to be replaced so that the mower can continue to be used. This handle can provide a genuine replacement for compatible models. This control handle is manufactured to exact standards by MTD and provides an exact fit. It is compatible with hundreds of models, including select models from RYOBI, Yard Machines, Troy-Bilt, Yard-Man, Husky, Bolens, and Cub Cadet. This part is also known as the control bar, control handle, engine stop handle, bail control, or mower bail. It is made of durable metal and sold individually. No tools are required for the installation of this part. To replace the handle, simply squeeze the existing control handle to remove it from the outer handle, and then align the new handle and slide it into place. When properly installed, the pressure will hold it in place and allow for proper operation.

Black plastic wheel hub cap for lawn tractors and riding mowers. Replaces cracked, broken, or missing hub caps. Snaps onto wheel hub for a finished look.

Auger bearing flange connects to the bearing to reduce friction during operation. Replace if worn or damaged to restore smooth auger rotation. Verify fit.

Replacement drive control cable for gas snow throwers. Connects handle control to engine drive system. Replace if cable is frayed, damaged, or broken.

Seals between carburetor and engine block to prevent air and fuel leaks. Replace if engine runs rough, leaks gas, or loses power. Verify fit by model.

Fix snow thrower auger that won't turn or spins slowly with a new auger belt. This rubber V-belt drives the auger rotation on two-stage models.

Metal carriage bolt with round head and threaded shank for lawn mowers and snow blowers. Replaces broken or missing hardware during repairs or assembly.

This is a versatile screw designed with flanged hex head and double-lead threads. It is a high-low self-tapping screw with one thread that is high and the other low for easier penetration. The twin threads also reduce the amount of material displaced when the screw is driven into the material. This type of screw also creates a firmer grip. This screw can also be used to secure a newly installed front cover or grill. This part is available as an individual replacement part. It is a genuine OEM part for use with specific models of snow throwers, lawn tractors, electric mowers, chippers, and log splitters from Bolens, Cub Cadet, Craftsman, Poulan, Ryobi, Toro, MTD, Troy-Bilt, Yard Machines, and Yard-Man.

Wing knob for lawn mowers and snow blowers. Secures chutes, bagger frames, and adjustable components. Replace if cracked, broken, or missing.