Parts for Kitchenaid KGCC506RBL05: 03 - Optional Parts

Size: 16 fl. oz.

Contains 35 - 7 x 9 inch wipes.

Size: 4 fl. oz.

This genuine wire harness routes electrical signals and power between components to restore proper operation and connectivity. It replaces damaged or frayed wiring to help eliminate intermittent power, control failures, or non-responsive functions. What it does:

• Carries power and control signals between appliance components to enable normal operation
• Replaces worn, burned, or broken wires and connectors that cause intermittent or no power
• Helps resolve issues like unresponsive controls, motors not running, or lights that won't turn on
• Preserves factory routing and connector fit for a secure, reliable connection

• One complete wire harness as shown

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the harness
• Compare connectors and wire colors to the old harness to ensure correct fit before installing
• Secure wires along original routing and fasten any clips or ties to prevent rubbing or pinching

This single-conductor replacement wire restores an electrical connection between components in compatible Whirlpool appliances. It's a straightforward part used when a damaged or broken wire prevents normal operation. What it does

• Carries electrical current between terminals or components to enable operation.
• Replaces frayed, broken, or heat-damaged wiring that can cause intermittent or no power to a component.
• Common symptom: affected circuit or component won't power on or works sporadically.
• Helps re-establish a reliable connection when the original wire is corroded or has a broken conductor.

• Disconnect power (unplug appliance or shut off circuit breaker) before starting any repair.
• Use proper wire connectors/crimping techniques and ensure secure, insulated connections.
• Verify correct routing and strain relief to avoid contact with moving parts or heating elements.

NAT to LP gas conversion kit

This ground screw secures the appliance grounding conductor to the chassis for a reliable electrical ground connection, helping maintain safety and proper operation. It's a direct-fit fastener used where a dedicated ground screw is required. What it does

• Fastens the grounding conductor to the appliance frame to maintain a secure earth/ground connection.
• Helps prevent electrical shock and reduces risk of stray voltage on the chassis.
• Addresses symptoms like intermittent or absent grounding and loose or corroded ground connections.
• Used wherever the original equipment grounding screw has been lost, damaged, or corroded.

• Disconnect power at the breaker and unplug the appliance before starting any work.
• Only attach to designated grounding points on the chassis; ensure the mating surface is clean and free of paint or corrosion.
• Use the correct driver and moderate hand torque—do not overtighten to avoid stripping threads.

This griddle creates a flat, continuous cooking surface that rests on your range or cooktop grates. It adds versatile space for items like pancakes and sandwiches, and replaces a worn or missing original griddle to restore safe use. What it does:

• Provides a broad, flat surface across burners for griddle-style cooking
• Direct replacement for a damaged, warped, or missing griddle
• Useful for foods that need a continuous surface (pancakes, eggs, grilled sandwiches)
• Common reasons to replace: wobbling/poor fit on grates, cracks, or persistent sticking from wear

• 1 griddle

• Turn all burners off and let the cooktop cool before placing or removing the griddle
• Position per your model's instructions so it sits flat and secure on the grates
• Preheat gradually on low to medium heat; handle only with oven mitts
• Allow the griddle to cool completely before cleaning or moving

This foam tape is used to seal and cushion mating surfaces in your appliance. Replacing a worn strip restores a snug fit, helps reduce noise, and helps maintain proper airflow, heat, or moisture control where specified by the manufacturer.

• Provides a compressible seal between components per the unit's parts diagram
• Cushions panels and trim to reduce vibration, buzzing, or rattling
• Helps prevent air, steam, or heat leaks at joints and seams
• Replace if the original tape is torn, flattened, missing, or contaminated

• Disconnect power and shut off gas/water as applicable; allow the appliance to cool before service
• Note the original tape placement; remove old material and residue, then clean and dry surfaces
• Apply per the service manual; avoid stretching; press evenly to ensure full contact
• If the OEM procedure calls for trimming, cut carefully to length and avoid gaps or overlaps

Size: 16 fl. oz. Spray bottle.

Razor blade scraper.

Keep your appliance performing and looking its best with this factory-authorized cleaner. It's formulated to dissolve built-up residues and deposits when used as directed, helping reduce odors and keep maintenance on track.

• Breaks down mineral scale, film, and other deposits that accumulate with normal use
• Helps address issues like lingering odors or visible buildup
• Supports ongoing performance and appearance when used per maintenance guidelines
• Use only as directed on the product label and in your owner's manual

• Read and follow all label directions and your appliance owner's manual before use
• Disconnect power and shut off water if required for your model's cleaning procedure
• Use in a well-ventilated area; wear gloves/eye protection as recommended
• Do not mix with bleach or other chemicals; rinse/flush as instructed before returning to service

Size: 10 fl. oz. Used on glass, ceramic and porcelain cooktops.

This switch harness is the factory wire assembly for a bank of four control switches. It links the switches to the appliance wiring so the controls operate reliably and deliver power to the circuits as intended.

• Connects four control switches in the panel to the appliance's main wiring harness
• Ensures proper routing of power through each switch circuit
• Typical symptoms: a function won't start or works intermittently when a switch is turned
• Visual clues: brittle/melted insulation, darkened connectors, or arcing at the switch bank

• Disconnect power at the breaker or unplug the appliance before servicing; verify no voltage is present
• Access the control area per your model's procedure
• Photograph or label wire positions; move connectors one at a time to the new harness
• Route and secure away from sharp edges and hot surfaces; verify all terminals are tight before reassembly