Parts for Maytag MGD6230HC3: Optional Parts (Not Included) Parts

This periscope extension piece helps position or extend a small duct/vent component inside the appliance so airflow or sensing elements reach the correct location. It's a simple replacement that restores proper alignment and fit. What it does

• Provides a 0.5-inch extension/positioning for an internal vent or sensor tube
• Restores proper clearance and alignment of airflow or sensing components
• Can reduce airflow restriction or misalignment-related symptoms
• Helps resolve intermittent venting, sensor mispositioning, or fitment issues

• One periscope extension piece

• Typical replacement is a simple swap; power off and unplug the appliance before starting
• Remove any access panels needed to reach the original periscope; retain mounting clips or gaskets
• Inspect surrounding parts for damage and replace if worn to ensure proper seal and operation

This 8 ft flexible exhaust hose directs airflow from the appliance to the home vent, helping maintain proper ventilation and reduce moisture and lint buildup. It's a straightforward replacement for worn or damaged ducting. What it does:

• Channels exhaust air from the appliance to the exterior vent
• Restores proper airflow to help reduce drying times and moisture buildup
• Helps prevent lint accumulation in the appliance exhaust pathway
• Reduces risk of poor performance caused by crushed, torn, or disconnected ducting

• One 8 ft flexible exhaust vent hose

• Disconnect power to the appliance before replacing the vent and follow all safety precautions
• Remove old ducting carefully to avoid scattering lint; clean vent openings before installing the new hose
• Ensure secure clamps or connections at both appliance and wall/roof vent to prevent leaks
• Follow local building codes and venting recommendations for appliance type and location

This connector restores a secure electrical connection between wires in the appliance, helping return reliable power and control to the affected circuit. It's a direct replacement designed to match the OEM fit and function. What it does:

• Joins two or more wires to complete an electrical circuit
• Replaces damaged, corroded, or loose terminals that cause intermittent power or control failures
• Provides a stable connection to reduce arcing and heat build-up at the joint
• Useful when visual damage or burnt insulation is present on the original connector

• Disconnect power to the appliance before servicing to avoid shock or injury
• Confirm wire colors and orientation before removing the old connector to ensure correct reassembly
• Use proper crimping or connector tools per OEM guidance; do not rely on loose twisting or temporary fixes
• If wiring or insulation is damaged beyond the connector, inspect and repair the harness.

This metal hose clamp secures flexible water or drain hoses to fittings to help prevent leaks and hose detachment. It's a compact replacement part for appliances that use band or spring-style clamps on hose connections. What it does:

• Holds a hose firmly on a barb or nipple to maintain a watertight connection
• Prevents leaks or dripping at hose junctions caused by loose fittings
• Reduces hose movement and vibration that can lead to wear or disconnection
• Works wherever a small appliance hose clamp is required

• Turn off and unplug the appliance and shut off water supply before starting
• Release hose pressure and drain residual water before removing the old clamp
• Use appropriate pliers or a screwdriver for the clamp type; avoid over-tightening

(18"- 29")

Approximately 8 feet.

This dryer vent directs exhaust air from the dryer to the home's venting system to restore proper airflow and help maintain safe drying performance. Use when the original vent is damaged, bent, or missing. What it does:

• Channels hot, moist air from the dryer to the exterior vent to prevent backflow into the laundry area
• Restores proper airflow that can reduce long drying cycles and excess heat buildup
• Helps keep lint and moisture moving out of the cabinet area when used with regular lint-trap maintenance
• Replaces cracked, crushed, or corroded vent parts that cause poor venting

• Disconnect electrical power (and shut off gas supply for gas dryers) before starting any work
• Install only with the correct vent length and profile for your dryer; avoid sharp bends and compressing the duct
• Secure connections with appropriate clamps or fasteners and check for leaks or obstructions after installation
• Clean the lint trap and inspect the vent path regularly to maintain safe operation

This dryer elbow is the molded duct connector that redirects exhaust from the dryer to the vent duct, helping restore proper airflow and reduce leaks around the outlet. It's a simple replacement for a cracked or loose elbow. What it does:

• Connects the dryer's exhaust outlet to the home vent duct to direct hot, moist air outside
• Replaces cracked, broken, or warped elbows that cause air leaks or rattling
• Helps reduce lint escape and improves exhaust path integrity when fitted properly
• Can eliminate visible gaps or misalignment at the dryer outlet

• One dryer elbow part

• Disconnect power (and gas supply for gas dryers) before servicing; follow all safety warnings
• Remove the dryer from the wall enough to access the outlet; loosen or remove clamps to swap the elbow
• Use appropriate duct clamps or approved tape to secure connections; ensure vent is clear of lint

This touch-up paint bottle restores small chips and scratches on painted appliance surfaces to improve appearance and help protect against rust. Easy-to-apply formula matches common appliance finishes for quick cosmetic repairs. What it does:

• Covers small chips, nicks and surface scratches to improve appearance
• Helps protect exposed metal from moisture and surface corrosion after damage
• Provides a precise application for targeted repairs on doors, panels and trim
• Can be used on painted steel and metal appliance surfaces (test in an inconspicuous area first)

• Clean and dry the repair area; remove loose paint and corrosion before applying
• Shake bottle well and apply sparingly with included applicator or a small brush
• Allow adequate drying time between coats and follow any manufacturer cure instructions on the label
• Wear gloves and work in a well-ventilated area; keep away from open flame and out of reach of children

This 5-foot flexible vent hose provides a replacement vent path for your dryer, restoring proper airflow to help clothes dry efficiently and reduce lint buildup. It's a straight, flexible vent designed for inline dryer ducting. What it does:

• Channels hot, moist air from the dryer to the home vent outlet to help shorten drying cycles
• Helps prevent lint accumulation in the dryer exhaust path when properly installed and maintained
• Can resolve symptoms like longer dry times, reduced airflow from the dryer, or overheating due to restricted venting
• Works as the inline connector between the dryer outlet and the household vent opening

• One 5 ft flexible dryer vent hose

• Disconnect power (and gas supply for gas dryers) before replacing the vent; follow all safety precautions
• Ensure the hose is not crushed or kinked and has a smooth path to the exterior vent for best performance
• Use proper clamps or fasteners to secure both ends and check for leaks after installation
• Clean lint from the dryer and duct before installing the new hose to maximize airflow

This wall elbow redirects the dryer vent through a wall opening, keeping the exhaust path secure and aligned for safe, efficient venting. Replaces a worn or damaged elbow to help restore proper airflow. What it does

• Provides a finished transition from the dryer vent pipe to the wall recess.
• Helps maintain a sealed vent path to reduce air leakage and lint buildup.
• Common fix for a cracked, loose, or broken elbow that causes noisy or inefficient venting.
• Works with standard dryer vent systems where a recessed wall box is used.

• Designed for use with compatible dryer vent housings;
• Turn off and disconnect the dryer before servicing; wear gloves to protect hands from sharp metal edges.
• Inspect surrounding venting and clear lint before final assembly to improve airflow and safety.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

This elbow is a molded hose connector that redirects fluid or airflow in the appliance, restoring proper routing for drainage or vent lines. It helps stop leaks and maintains correct hose alignment for reliable operation. What it does

• Redirects hose or duct routing at an angle to fit tight spaces
• Restores a secure connection where a cracked or broken elbow causes leaks
• Helps prevent kinks or pinched hoses that can cause poor drainage or reduced airflow
• Supports proper sealing when used with the correct clamps or gaskets

• One elbow connector

• Disconnect power and shut off water before replacing the part
• Inspect mating hose ends and clamps; replace damaged hoses or clamps for a secure seal
• Ensure correct orientation and fully seat the elbow before tightening clamps
• Do not force the part into place; confirm fit and alignment to avoid stress or leaks

Dryer Vent Test Kit ensures your dryer's vent system is operating properly. Kit includes two tests depending on the location of your dryer's lint screen: One for the lint screen in the top of your dryer, and one for the lint screen in the front of your dryer. Instructions included.

This Dryer Repair Kit refreshes the tumble system by replacing the high-wear parts that cause noise and poor drum movement. Restore smooth, reliable operation and help extend the life of your dryer. What it does:

• Renews the drive path so the drum turns smoothly and consistently
• Restores proper belt tension and tracking with a new idler pulley
• Replaces worn or noisy drum support rollers to reduce squeaks and thumps
• Helps address symptoms like squealing/squeaking, rumbling/thumping, intermittent or no tumble, and burnt-rubber smells

• Kit includes: drum belt, idler pulley, and drum support rollers

• Disconnect power and shut off gas before servicing
• Access the drum per your model, support it when swapping rollers, and note the original belt routing
• Clean lint and roller shafts; do not lubricate rollers; route the new belt around the motor and idler as designed
• Spin the drum by hand to ensure smooth movement before reassembly and test run

• Replace all drum rollers at the same time to maintain even wear and quiet operation

This 6-foot dryer vent duct connects your dryer's exhaust outlet to the wall vent. It provides a secure path for moist air to exit the home, helping maintain airflow and consistent drying performance. What it does:

• Vents hot, moist air from the dryer to the exterior
• Replaces crushed, torn, or lint-clogged ducting
• Helps address longer dry times, heat buildup/shut-offs, or moisture and lint around the dryer
• Supports a short, direct run to reduce kinks and airflow restrictions

• One 6-foot dryer vent duct

• Disconnect power; for gas models, turn off the gas supply before starting
• Pull the dryer forward and remove old ducting and lint/debris from connections
• Attach the duct fully to the dryer outlet and wall vent and secure with clamps; avoid sharp bends or crushing
• Move the dryer back carefully and confirm strong airflow at the exterior vent hood

This flexible, narrow brush reaches under and behind the cabinet to sweep dust and lint from condenser coils and vents. Cleaning built-up debris helps restore airflow and support proper cooling performance.

• Sweeps dust, lint, and pet hair from condenser coils and ventilation areas
• Flexible reach helps access coils beneath or behind the appliance
• Aids proper heat dissipation by clearing airflow paths
• Helpful when coils are visibly dirty, cooling seems weak, or the unit runs longer than usual

• Unplug or disconnect power before cleaning
• Remove the toe grille or rear access panel if needed to access coils
• Brush gently along the coil fins; avoid bending fins or damaging tubing
• Vacuum or wipe up loosened debris before replacing any panels and restoring power

Side and bottom exhaust kit.

This Dryer Drying Rack creates a stationary shelf inside the drum so items that shouldn't tumble—like shoes, sweaters, and hats—can dry gently. Replace a missing or damaged rack to restore safe, non-tumble drying capability.

• Provides a stable platform inside the dryer for items that need to stay still while drying
• Helps reduce wear, scuffing, and noise from tumbling delicate or bulky items
• Restores function when the original rack is cracked, warped, or missing
• Common symptoms: rack won't seat/lock, sits unevenly, or items won't stay on the rack

• Disconnect power before installing
• Open the door and seat the rack so the rear support engages the back ledge/slots and the front rests on the door opening
• Ensure the rack is secure and clear of the rotating drum; load items evenly
• Remove the rack before returning to normal tumble cycles