Parts for Electrolux EI30MO45GSA: 03 - Oven, Cabinet Parts

This capacitor kit replaces the start/run capacitor assembly for refrigerator compressors, helping the compressor start reliably so the appliance can cool properly. Use it to restore normal compressor operation when the capacitor has failed. What it does

• Provides the electrical boost the compressor motor needs to start and run
• Commonly used when the compressor hums but won't start or the fridge won't reach temperature
• Helps prevent repeated hard starts that can damage the compressor
• Works with the compressor's relay and overload to enable proper motor function

• One capacitor kit

• Disconnect power to the appliance before starting work to avoid shock
• Discharge capacitors before handling; capacitors can hold a charge after power is removed
• Access usually requires removing the refrigerator rear lower service panel; keep track of fasteners and wiring

This interior refrigerator lamp provides reliable lighting inside the fresh-food compartment so you can see contents clearly. It replaces a dim or non-working lamp to restore normal interior illumination. What it does:

• Provides interior lighting for the refrigerator compartment
• Replaces a burned-out, flickering, or intermittently working lamp
• Helps you find food and check expiration labels without opening the compartment longer than necessary
• Works with the existing lamp housing and socket when compatible

• One interior refrigerator lamp

• Disconnect power to the appliance before replacing the lamp to avoid electrical shock
• Allow the lamp and surrounding area to cool before handling
• Handle the lamp carefully to avoid breakage; dispose of broken bulbs per local regulations
• Check the socket and appliance light switch for faults if the lamp does not light after installation.

This drive motor restores rotational power to the appliance's drum or agitator so loads spin and drain correctly. It's a direct-replacement motor designed to restore normal wash and spin cycles when the original motor fails. What it does:

• Provides the mechanical drive force for the washer drum/agitator so clothes tumble and spin
• Re-establishes proper agitation and spin speed control when a worn or failed motor causes no-spin or no-agitate symptoms
• Operates with the appliance's existing pulley, belt, or coupling
• Works as the core rotating component tied to load movement and draining functions

• One motor

• Disconnect power and water before beginning any repair; follow the appliance service manual for safe access
• Replacement typically requires removing cabinet panels, drive belt or coupling, and electrical connector—avoid forcing parts
• Inspect associated belts, couplings, and mounting hardware; replace worn items to prevent repeated failures

The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.  

Symptoms of a bad door switch can include:

• Oven failing to automatically go into bake or warm modes after door closure
• Interior lights not turning on when the door is opened
• Control buttons/display remaining constantly lit instead of dimming
• Oven not heating or functioning properly in different modes

Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.

This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.

This thermal fuse stops excessive heat by opening the circuit when temperatures get too high, protecting the appliance and its components. Replace a blown fuse to restore normal heating or safety shutdown functions. What it does:

• Acts as an over-temperature safety device to interrupt power when internal temps exceed safe limits
• Commonly linked to symptoms such as no heat, intermittent heating, or an appliance that won't start
• Prevents further damage by cutting power when a serious overheating condition occurs
• Functions as a single-use safety cutout—if it's open, it must be replaced

• One thermal fuse

• Disconnect power before testing or replacing; verify no voltage present
• Test continuity with a multimeter to confirm the fuse is open before replacing
• Replace with the same part number and rating; do not bypass or substitute with wire
• If the fuse failed, inspect the appliance for underlying issues before returning to service

This magnetron is the high-voltage microwave source used in countertop and over-the-range ovens to heat food. Replacing a failed magnetron restores the oven's ability to generate microwave energy for cooking. What it does:

• Generates microwave energy that heats and cooks food inside the oven cavity.
• Commonly needed when the oven runs but does not heat, or heating is very weak.
• May be replaced if you hear loud buzzing, intermittent heating, or experience arcing/sparking inside the cavity.
• Works with the oven's high-voltage circuit and waveguide to distribute microwaves evenly.

• One magnetron (single unit as shown)

• High-voltage component: always disconnect power and discharge the capacitor before service.
• Inspect and replace any damaged waveguide cover, seals, or mounting hardware; secure all connections and shielding per OEM instructions.
• Follow all safety warnings in the oven's service manual and dispose of the old magnetron according to local regulations.

This replacement motor restores the rotation your appliance relies on to move air or drive a mechanism, bringing normal operation and performance back when the original motor has failed or become noisy. What it does:

• Converts electrical power into controlled shaft rotation to drive the associated component
• A failing motor may cause no movement, intermittent operation, or unusual humming/grinding noises
• Can contribute to reduced performance if the driven part doesn't run as intended
• May present with overheating smell or visible signs of wear on the old unit

• One motor

• Disconnect the appliance from power before servicing
• Note wire locations and connector orientation; transfer any brackets, grommets, or hardware from the old motor
• Handle sheet-metal edges carefully; wear cut-resistant gloves
• After installation, confirm the shaft spins freely by hand before restoring power and testing

Control transformer that supplies the low-voltage power needed for the appliance's electronic control/console, restoring reliable operation when the original transformer fails or the display and controls lose power. What it does:

• Converts incoming line voltage to the low-voltage supply used by the control board and console.
• Keeps the display, touchpad/keys and control electronics powered and stable.
• Common symptoms of a failing transformer: unlit or blank display, unresponsive controls, intermittent operation, or control board power loss.
• Replace a visibly burned, cracked, or shorted transformer to prevent further electrical damage.

• Always disconnect power to the appliance before servicing to avoid electric shock.
• Take care with wiring: match original connector positions and secure all wire nuts/terminals.
• Inspect mounting hardware and insulation; replace any damaged fasteners or wires.

This replacement power cord restores mains power to compatible Frigidaire appliances, providing a safe, factory-style connection for reliable operation. Use it when the original cord is damaged or not supplying power. What it does:

• Replaces a worn, frayed, or damaged power cord to restore electrical connection
• Provides the appliance's main AC connection so controls, heating, and motors can operate
• Helps resolve symptoms such as intermittent power, no power to the appliance, visible cord damage, or exposed wiring
• Matches the OEM form and function for a direct-replacement fit when the part number is correct

• One replacement power cord

• Disconnect power at the breaker or unplug the appliance before installing
• Route and secure the cord per manufacturer instructions; tighten terminal connections to proper torque

This adjustable leveling foot replaces a worn or damaged appliance leg to restore stable, even support and reduce rocking. It helps keep the appliance level on uneven floors for proper operation and safe use. What it does:

• Provides a stable, height-adjustable support point for the appliance cabinet
• Lets you level the appliance to prevent rocking or uneven door alignment
• Helps protect floors by keeping the appliance weight distributed correctly
• Restores proper clearance for ventilation and door operation when uneven

• One adjustable leveling foot

• Unplug the appliance and move it to access the mounting area before working
• Support the appliance so it cannot tip while adjusting or replacing the foot
• Thread or press the foot into place per the original mounting style; tighten by hand or with basic hand tools
• Recheck level and stability after installation and reconnect power

This outer cabinet provides the refrigerator's main exterior housing, restoring structural support and the appliance's finished appearance. Replaces a damaged or dented outer shell to help maintain proper component alignment and fit. What it does:

• Forms the refrigerator's outer housing and supports internal components and panels
• Protects internal parts from damage, dust, and moisture
• Restores proper alignment and mounting for doors, trim, and internal assemblies
• Addresses symptoms like visible dents, loose or misaligned panels, rattling, or gaps around the cabinet

• Disconnect power and remove food before beginning any repair
• This heavy panel may require two people and basic hand tools to remove and install
• Keep mounting hardware and insulation in place or transfer from the old cabinet as instructed by the service manual

This latch hook engages the door catch/lock on your appliance to keep the door securely closed. Replacing a worn or broken hook restores proper latching so cycles can start and run reliably. What it does:

• Engages the mating latch/strike to hold the door shut
• Ensures the door switch/lock is satisfied so the appliance can operate
• Helps prevent the door from popping open during use
• Common symptoms: door won't stay closed, must push/slam to start, "door open" errors, intermittent stopping

• 1 latch hook

• Disconnect electrical power before servicing; allow any hot surfaces to cool
• Wear cut-resistant gloves; edges and panels can be sharp
• Transfer and reuse original screws/fasteners if not supplied
• After installation, verify door alignment and latch engagement; inspect the mating strike/lock if the issue persists

The Door Release Lever is an OEM part for Frigidaire microwaves. It facilitates the smooth opening of the microwave door by engaging the latch mechanism when the door release button is pressed, ensuring convenient access to the microwave cavity.

Causes of a bad door release lever can include regular wear and tear, exposure to heat, or physical damage from forceful operation.  

Symptoms of a bad Microwave Door Release Lever include:

• Difficulty opening the microwave door
• The door not latching properly or remaining ajar
• The door release button not functioning correctly
• Unusual resistance or noises when opening the door

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This duct-magnetron (waveguide duct) directs microwave energy from the magnetron into the oven cavity and helps protect internal components. Replacing a damaged duct restores proper wave guidance and prevents arcing or burn damage. What it does:

• Channels microwaves from the magnetron into the cooking cavity for even energy transfer
• Shields surrounding components from heat and sparking that can occur with a cracked or warped duct
• Helps prevent arcing, burning smells, and visible sparks inside the microwave
• Maintains proper alignment between the magnetron output and the oven waveguide

• One duct-magnetron (waveguide duct) as shown

• Unplug the appliance and ensure power is disconnected before servicing
• Microwave high-voltage components can store lethal charge; discharge capacitors and follow safety procedures
• Handle carefully to avoid bending or further damaging the duct; wear gloves and eye protection

This replacement cover restores a clean, secure fit over an opening on your appliance, helping shield internal components from dust, moisture, and debris. Replace a damaged or missing cover to maintain proper protection and appearance. What it does:

• Shields internal parts from grease, dust, and debris intrusion
• Helps maintain proper airflow and component protection as designed
• Reduces vibration or rattling from loose or broken panels
• Restores a finished, factory look when the original is cracked or missing

• 1 cover

• Disconnect power to the appliance before servicing
• Note fastener locations and orientation for correct reinstallation
• Reuse original screws/clips unless your unit specifies otherwise
• Use gloves and caution—panel edges and surrounding metal can be sharp

This bushing guides and supports a rotating shaft to reduce wear and keep moving parts aligned, restoring smooth, quiet operation. Fits specific Frigidaire appliances—use the OEM part number to fit for your model. What it does

• Supports a rotating shaft or drum to prevent metal-on-metal contact
• Reduces friction and wear that can cause squeaks, grinding, or rough rotation
• Helps maintain proper alignment for consistent appliance performance
• Commonly replaces worn or damaged bushings that allow excessive play

• Disconnect power before servicing and access the affected assembly per your model's service manual
• Remove the worn bushing and any debris; press or tap the new bushing into place squarely
• Inspect mating shaft/surface for scoring or wear; replace or repair if damaged
• Use only OEM-recommended lubricants if specified by the manufacturer; do not assume grease is required

This support assembly secures and stabilizes an appliance component to the cabinet or frame, restoring proper alignment and reducing vibration. Ideal when a broken or worn support causes movement or instability of the affected area. What it does:

• Provides structural mounting to keep panels, controls, or other components properly aligned.
• Reduces vibration, rattling, or visible sagging caused by a failed or loose support.
• Restores reliable attachment after damage, deformation, or worn mounting points.
• Matches OEM diagram locating for direct-replacement fit when replacing the faulty part.

• Disconnect power and unplug the appliance before starting any repair.
• Follow the OEM diagram for correct placement and fastener locations.
• Use appropriate hand tools and wear gloves to avoid sharp edges; inspect surrounding mounting hardware and replace if damaged.

The Turntable Tray is an OEM part for Frigidaire microwaves. It sits inside the microwave and rotates food to ensure even cooking and heating. Made of durable glass, this tray is designed to withstand high temperatures and the repetitive motion of the microwave's turntable motor.

Damage can occur due to accidental drops, placing heavy items on the tray, or thermal stress from repeated heating cycles.

Symptoms of a bad turntable tray include:

• Cracks or chips on the glass surface
• Unstable or wobbling movement during operation
• Inability to rotate smoothly
• Food not heating evenly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement appliance label provides the factory identification and safety information fastened to the appliance so you can read model/serial and safety/warning text clearly. It restores legible markings for servicing and ownership records. What it does

• Shows the appliance identification, model/serial or rating area and factory safety/warning text so technicians and owners can service data.
• Helps ensure required safety and operating instructions remain visible and readable.
• Replaces a torn, faded, or missing label that can make identification and troubleshooting harder.
• Supports accurate parts ordering and service by restoring the original markings.

• One replacement label

• Peel-and-stick replacement; clean and dry the surface thoroughly before applying.
• Align carefully and press from one edge to the other to avoid bubbles; firm pressure ensures adhesion.
• Do not stretch or trim the label unless explicitly specified by the equipment instructions.
• For safety, disconnect power or follow manufacturer safety precautions before working near electrical components.

This is a replacement screw used to secure appliance components and panels so assemblies stay stable and aligned. It provides a straightforward fix when a mounting fastener is missing, stripped, or damaged. What it does

• Secures panels, brackets, or trim to prevent movement and vibration
• Stops rattling or loose parts caused by missing or damaged screws
• Restores proper fit and alignment of the affected assembly
• Works wherever the OEM-designated screw of this size and thread is required

• Turn power off or unplug the appliance before working on electrical areas
• Use the proper-size driver to avoid stripping the head
• Start threads by hand, then tighten until snug — do not overtighten
• If the original screw is corroded or the hole is damaged, inspect mating parts for repair before installing

This adhesive appliance label replaces a worn or missing identification/warning sticker so important model, safety or operating information remains visible. Keeps service and safety info readable for owners. What it does

• Replaces faded or damaged identification, rating or warning graphics on the appliance
• Restores legible safety and operating information that helps prevent misuse
• Helps confirm appliance details during troubleshooting and repairs
• Adhesive backing sticks to clean, flat surfaces for a long-lasting replacement

• Clean and dry the mounting surface; remove oils, dust and loose residue before applying
• Peel backing and press the label firmly in place, smoothing out air bubbles
• Replace only on compatible surfaces and locations; do not stretch or fold the label
• If removing old adhesive, use a plastic scraper and a mild solvent in a well-ventilated area; disconnect power to any nearby electrical components before working

This replacement identification decal restores legible equipment labeling so model, rating and safety information are visible for service and ownership. It helps replace faded, torn or peeling labels to improve readability and compliance. What it does:

• Provides a clear, adhesive identification decal with printed model/rating/safety information
• Replaces faded, torn or peeling factory labels that are hard to read
• Helps owners identify the appliance correctly during service
• Maintains visible safety and rating information required for repair or inspection

• Clean and dry the installation surface thoroughly before applying
• Peel backing and press decal firmly, smoothing out air bubbles for full adhesion
• Do not stretch, reposition repeatedly, or apply to wet/oily surfaces
• If label covers a vent or operational opening, confirm placement with service manual