Parts for Electrolux EI30SM55JSA: 03 - Oven,Cabinet Parts

Microwave not heating but humming loudly? A failed high-voltage diode is often the cause. This rectifier converts AC to DC for the magnetron circuit.

This is a high voltage capacitor used in the microwave's magnetron circuit. It stores and releases electrical energy to help power the magnetron, which generates the microwaves that heat food. Replace this capacitor if the microwave runs but does not heat, hums loudly without cooking, or if the capacitor has visibly bulged or leaked. Always discharge the capacitor before handling, as it can retain a dangerous charge even when unplugged.

This control switch regulates heat to a surface burner so the cooktop reaches and holds the selected temperature. Restores responsive burner control and consistent cooking performance. What it does:

• Sends variable power to a surface burner to adjust heat levels as you set the knob
• Commonly replaces a switch that causes a burner to stay cold, not heat, or only work at one setting
• Can fix clicking, intermittent operation, or loss of variable control on the affected element
• Works with the cooktop's control knob and wiring harness to manage element output

What's included:

• One replacement infinite burner control switch

Install notes:

• Disconnect power to the appliance before beginning any work
• Remove the cooktop or control panel as needed to access the switch; keep track of mounting hardware
• Match wire locations and connector orientation when reattaching harness; take a photo first if helpful

If your microwave runs but doesn't heat food, the magnetron likely failed. This part generates the microwave energy. Moderate DIY repair, 1-2 hours.

The Door Switch is an OEM replacement part for Frigidaire wall ovens. It is a component located on the oven door that detects when the door is opened and closed. The door switch works alongside the control board to regulate oven operations based on door position.  

Symptoms of a bad door switch can include:

• Oven failing to automatically go into bake or warm modes after door closure
• Interior lights not turning on when the door is opened
• Control buttons/display remaining constantly lit instead of dimming
• Oven not heating or functioning properly in different modes

Causes relate to normal wear over extended use as the door switch mechanism cycles with frequent door openings and closings. Moisture exposure or impacts could also degrade switch performance.

This OEM Frigidaire switch is compatible with Amana, Jenn-Air, KitchenAid, and some Electrolux wall oven models as well.

Replacement power cord for your microwave. Connects the appliance to your electrical outlet. Order a new cord if yours is frayed, damaged, or missing.

Replace your microwave's light socket if bulbs fail to illuminate despite having power. Restores interior or under-cabinet lighting. Verify fit by model.

This small electric motor sits beneath the microwave floor and rotates the turntable tray during cooking to ensure even heat distribution. It connects to the turntable coupler or drive shaft and operates at low RPM. Replace this motor if the turntable stops spinning, rotates intermittently, or makes grinding or humming noises without turning.

Microwave won't turn on, made popping noise, or smells like burned electrical? The noise filter often fails when solder joints arc or short out.

This is a replacement light bulb for the interior cavity of a microwave oven. It illuminates the cooking area so you can monitor food while it heats. Replace this bulb if the interior light no longer turns on when the door is opened or during operation, and you have confirmed the bulb socket and wiring are functioning properly.

This is a black plastic lens and frame assembly that covers the interior lamp on a microwave oven. It protects the light bulb from grease and moisture while diffusing light inside the cooking cavity. Replace this lens if it is cracked, yellowed, melted, or missing, which can leave the bulb exposed to splatter and reduce interior illumination.

This frame holds and protects the light lens cover inside the microwave, keeping the interior bulb shielded while allowing light to pass through. It snaps or screws into place over the light housing area. Replace this frame if it is cracked, warped, or missing, which can leave the light bulb exposed to moisture and food splatter.

Glass cover for microwave hood lamp. Protects the light bulb from grease and debris. Replace if cracked, broken, or missing to restore proper lighting.

3mm x 8mm screw secures trim, panels, and brackets inside your microwave. Replace missing or stripped screws to restore proper fit and alignment.

Controls airflow in your microwave's exhaust vent system. Installs between blower and duct. Replace if cracked, broken, sticking, or missing.

Replacement glass turntable tray for your microwave. Installs on the rotating support to hold food during cooking. Replace if cracked, chipped, or broken.

This is the roller guide assembly that sits on the floor of the microwave and supports the glass turntable tray, allowing it to rotate smoothly during cooking. It typically consists of a ring with small wheels or rollers. Replace this part if the turntable wobbles, does not rotate evenly, or if the rollers are broken or worn, which can cause uneven cooking or noise during operation.

Replace your worn or missing microwave door bushing. This small plastic component helps the door hinge operate smoothly and maintain proper alignment.

This is a plastic bracket that holds the door interlock switches in proper alignment inside the microwave's door latch assembly. It ensures the switches are correctly positioned to detect when the door is open or closed. Replace this part if the microwave won't start, runs with the door open, or if the switch holder is cracked or broken.

Microwave overheating or not venting properly? A worn blower wheel restricts airflow. This fan blade restores cooling and exhaust ventilation.

Microwave duct that directs airflow from the cavity to the exterior vent. Replace if cracked, damaged, or missing for proper ventilation performance.

This clear light lens covers and protects the interior lamp, directing and diffusing light inside the appliance for better visibility. It replaces a cracked, yellowed, or missing lens to restore even interior illumination. What it does:

• Protects the interior lamp from spills, steam, and physical contact
• Diffuses and directs light for more even illumination inside the compartment
• Restores visibility when the original lens is cracked, cloudy, or missing
• Helps prevent direct contact with the bulb for safer operation

What's included: One clear light lens. Install notes:

• Disconnect power to the appliance before starting any work
• Allow the bulb to cool completely before removing the old lens
• Handle the lens gently to avoid cracking; align tabs or clips and snap into place
• If the lens uses screws, tighten securely but do not overtighten to avoid cracking

Replacement mounting bracket for microwave installations. This support bracket secures the unit to cabinetry or walls. Needed when original is cracked or bent.

The microwave front rack support holds the cooking rack in proper position within the microwave cavity, attached to the interior front wall. Replace if the rack won't stay in place, support is bent or broken, or if it interferes with turntable operation.

A small rubber cushion that cushions and isolates moving parts to reduce noise, vibration, and wear. Fits where a soft bumper or spacer is required to protect surfaces and keep components aligned. What it does:

• Absorbs shock and reduces rattling between parts
• Prevents metal-to-metal contact that can cause noise or wear
• Keeps panels, doors, or assemblies properly spaced and aligned
• Helps stabilize components during operation

• One rubber cushion/buffer

• Turn off and unplug the appliance before servicing to avoid shock or injury
• Inspect the mounting area and clean debris before installing the cushion
• Press or snap the cushion into place; if fasteners are required, use the OEM-specified screws or clips

This small rubber cushion cushions contact points to reduce vibration and prevent metal-on-metal noise or surface wear. It restores quiet, stabilizes moving parts, and helps maintain proper alignment for smooth operation. What it does:

• Acts as a soft bumper between components to absorb shock and reduce rattling.
• Prevents direct contact that can cause scratches, chipping, or wear.
• Helps maintain proper spacing and alignment of panels or assemblies.
• Commonly replaced when torn, flattened, hardened, or missing.

• Designed for a simple swap; remove the old cushion and press the new cushion into place.
• Inspect the mounting surface for debris or damage before installing.
• Use basic hand tools only; disconnect power/unplug appliance if servicing near electrical connections.
• If adhesive is present, allow any adhesive to set according to the adhesive manufacturer's instructions.

This is a replacement adhesive identification label used to restore factory markings and safety information on the appliance. It helps keep model, rating or warning information legible for service and safe operation. What it does

• Replaces a torn, faded, or missing appliance identification label
• Restores readable model, serial, rating or warning information that owners rely on
• Helps prevent confusion during service by keeping factory markings visible
• Maintains appliance appearance and compliance with original labeling

• One adhesive identification label

• Clean and dry the application area before installing to ensure proper adhesion
• Align the label carefully and press firmly from one side to the other to avoid bubbles
• No specialized tools required; avoid stretching or folding the label during placement

This replacement identification label displays appliance model, serial, and rating information so you can correctly identify your unit for service or parts ordering. Durable adhesive backing helps keep factory information legible. What it does:

• Replaces a torn, faded, or missing identification/rating label so model and electrical data are readable
• Helps technicians and owners model/serial and voltage/current ratings during diagnosis or repairs
• Prevents confusion when ordering parts or scheduling service by restoring original identification
• Non-electrical — does not affect operation of the appliance

• Clean and dry the mounting surface before applying for best adhesion
• Peel backing and press firmly; avoid stretching or folding the label
• Do not place over vents, seals, or moving parts; install in the original label location if known

Grease filter for range hoods and over-the-range microwaves. Dimensions: 5-7/8" x 7-7/8" x 3/32" (5.875 x 7.875 x 0.09375). Rectangle shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.

Secures panels and components inside your microwave, keeping parts aligned and reducing rattles. Replace when clip is broken, cracked, or missing.

Mounting screw for microwave and wall oven assemblies. Replace if lost, stripped, or damaged during installation or service. Secures components.

Replacement mounting screw that secures panels, trim, and internal components in microwaves and wall ovens. Needed when screws are stripped, missing, or lost.

This is a replacement screw used to secure appliance components and panels so assemblies stay stable and aligned. It provides a straightforward fix when a mounting fastener is missing, stripped, or damaged. What it does

• Secures panels, brackets, or trim to prevent movement and vibration
• Stops rattling or loose parts caused by missing or damaged screws
• Restores proper fit and alignment of the affected assembly
• Works wherever the OEM-designated screw of this size and thread is required

• Turn power off or unplug the appliance before working on electrical areas
• Use the proper-size driver to avoid stripping the head
• Start threads by hand, then tighten until snug — do not overtighten
• If the original screw is corroded or the hole is damaged, inspect mating parts for repair before installing