Parts for Electrolux EMBS2411ABA: Oven,Cabinet Parts

This cover is a protective trim piece that shields and neatly finishes exposed components on your appliance. Replacing a cracked or missing cover restores protection and a clean, factory look while helping prevent accidental contact with internal parts.

• Conceals and protects wiring, mechanisms, or mounting hardware from dust and incidental contact
• Restores proper fit and finish for a clean appearance
• Helps ensure components remain secured and unobstructed
• Common symptoms include cracks, broken tabs, discoloration, or a missing/loose cover

• Disconnect power before servicing; shut off water supply if working near water lines
• Retain and reuse original screws or clips; transfer any clips from the old part if applicable
• Align tabs/slots and secure without overtightening to avoid damage
• The cover sits flush and doesn't interfere with doors, drawers, or moving parts

This diode is an electrical rectifier used on refrigerators to allow current flow in one direction and protect circuits from backfeed. Replacing a faulty diode restores proper circuit behavior and helps the appliance run reliably. What it does:

• Allows current to flow in a single direction to protect control and relay circuits
• Prevents backfeed that can damage electronic components
• Can be linked to intermittent operation, failure to start, or control-board-related faults
• Used wherever a single-direction current path or transient protection is required

• High-level replacement; disconnect power at the breaker or unplug the appliance before starting
• Confirm orientation/polarity matches the original during installation
• Use appropriate tools; avoid shorting leads or touching circuit traces

This replacement refrigerator water filter cartridge helps restore clean tasting water and ice by trapping common impurities. Designed as a direct-fit replacement to maintain your fridge's filtered water supply and improve taste clarity. What it does:

• Filters particulates and common contaminants to improve water and ice taste
• Helps reduce visible sediment and cloudiness from the dispenser and ice maker
• Restores normal dispensing performance when an old filter causes off-flavors or odors
• Supports consistent filtered water flow when installed and maintained

• Turn off the water supply and follow the refrigerator's filter-replacement instructions before starting
• Push/rotate or slide per your model's procedure until the filter locks in place; ensure a secure seal
• Run water through the dispenser for a short time after installation to flush air and initial carbon fines
• Replace regularly per the refrigerator manufacturer's recommendation or sooner if flow decreases or taste returns

This Fuse is an OEM part for Frigidaire microwaves. It's a critical safety component designed to protect the microwave from electrical overload by breaking the circuit if the current is too high. This fuse is specifically tailored to fit and function properly with Frigidaire microwave models, ensuring safety and reliability.

Fuses in microwaves can blow due to power surges, electrical faults within the appliance, or overheating caused by restricted airflow or malfunctioning components. A blown fuse prevents the microwave from operating as a safeguard against potential electrical damage or fire hazards.

Symptoms of a blown fuse include:

• The microwave suddenly stops working and doesn't turn on.
• No response from the microwave's control panel or display.
• The microwave is completely unresponsive, even when the door is opened or closed.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This temperature sensor monitors internal fridge/freezer temperature so the control board can regulate cooling and defrost cycles for more consistent temperatures and food safety. What it does

• Measures compartment temperature and sends readings to the control board.
• Helps the refrigerator maintain set temperatures by enabling accurate cooling cycles.
• Supports proper defrost control when used in defrost/evaporator applications.
• A failing sensor can produce temperature fluctuation, poor cooling, or longer run times.

• One temperature sensor

• Disconnect power before servicing to avoid shock or compressor damage.
• Handle the sensor and connector gently; avoid pulling on wires.
• Verify location and routing match the original; secure sensor to prevent contact with moving parts.

A push-button door switch that tells the appliance when the door is open or closed so lights, fans, or controls respond correctly. Replaces a worn or broken door-actuated switch to restore normal operation and interior lighting. What it does:

• Detects door open/closed position to control interior lights or related circuits
• Stops lights from staying on when the door is closed, preventing unnecessary power use
• Restores proper cycling of door-dependent functions and controls
• Commonly used when lights fail to turn on/off or when door-operated features are intermittent

• One replacement push-button door switch

• Disconnect power before servicing to avoid shock or damage
• Access typically requires removing interior trim or the light housing—keep fasteners for reassembly
• Verify switch orientation and terminal connections match the original before connecting

This infinite switch controls the heat level for an electric cooktop surface burner, restoring adjustable power to the element for even cooking and reliable temperature selection. What it does:

• Regulates electrical power to a single surface heating element so you can set low-to-high heat.
• Provides stepped "infinite" control positions rather than a simple on/off.
• Replaces a worn or failed control that causes a burner to not heat, stay stuck on one setting, or heat inconsistently.
• Uses standard spade-terminal connections found on many electric ranges.

• Disconnect power at the breaker before servicing—this part services live-voltage circuits.
• Access typically requires removing the cooktop or rear console; handle ceramic glass cooktops carefully to avoid cracking.
• Confirm terminal layout and mounting orientation before removal; take a photo of wiring for reassembly.

The Door Switch is an OEM part for Frigidaire microwaves. It plays a crucial role in the microwave's overall function by detecting when the door is open or closed. The door switch communicates this information to the control board, enabling it to safely operate the microwave's electronic components and magnetron when the door is shut.

Symptoms of a bad door switch include:

• The microwave failing to operate or function properly with the door closed  
• Inability to start or pause operation when the door is opened
• Error codes or failure messages appearing on the display related to door functionality

Causes of a bad door switch can be wear and tear over time, damage from repeated opening and closing of the microwave door, or impact from accidental mishandling. 

This OEM replacement is also compatible with Electrolux, Admiral, Crosley, White-Westinghouse, and Kenmore models.
 

This replacement control switch completes an internal circuit to enable and regulate an appliance function. It restores reliable on/off or selector operation so the appliance responds correctly to user inputs. What it does

• Acts as the electrical contact that opens or closes a circuit to start or stop a function.
• Commonly linked to symptoms such as the appliance not powering on, a function not engaging, or intermittent operation.
• Replaces a worn, burnt, or unresponsive switch to restore normal control responsiveness.
• Works as a direct-fit electrical replacement when the original switch is faulty.

• One replacement switch.

• Disconnect power to the appliance before inspecting or replacing the switch to avoid shock.
• Verify the old switch matches the new part visually and by terminal layout before installation.
• Use basic hand tools; avoid forcing connectors—ensure firm, correct terminal connections.

This mounting bracket supports and secures appliance panels or components, restoring proper alignment and stable fit. It replaces a damaged, bent, or missing bracket so affected parts sit securely and operate without excess movement. What it does:

• Secures panels, trim, or assemblies to the appliance chassis to maintain correct alignment
• Replaces a worn or damaged bracket that can cause loose or rattling panels
• Helps prevent misalignment that may interfere with door or component operation
• Restores a stable mounting point for reliable, quiet performance

• Disconnect power and water supply (if applicable) before starting any repair
• Verify correct bracket location and orientation before fastening
• Use existing or manufacturer-recommended fasteners; do not overtighten to avoid cracking

This Turntable Motor is an OEM part for Frigidaire microwaves. Responsible for the rotation of the microwave's turntable, which ensures even cooking and heating of food. This motor ensures that the turntable operates smoothly and reliably, maintaining the efficiency of your microwave.

A malfunctioning motor can lead to uneven heating or cooking of food, as the turntable is integral to the microwave's ability to distribute heat uniformly.

Symptoms of a faulty turntable motor include:

• The turntable does not rotate when the microwave is in use.
• Intermittent or erratic movement of the turntable.
• Unusual noises coming from the turntable area during operation.
• Food is unevenly cooked or heated, indicating inconsistent turntable motion.
• The microwave operates normally except for the turntable function.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

This glass turntable tray sits on the microwave's roller support to provide a stable, rotating surface for even heating. Replacing a cracked or missing tray restores safe operation and helps keep spills contained for easier cleanup.

• Provides a flat, heat-resistant surface for dishes and cookware
• Engages the center coupler to rotate food for more uniform cooking and defrosting
• Removes easily for cleaning and helps contain minor spills
• Common symptoms: cracked/chipped glass, wobbling, won't sit level, or tray no longer rotates due to a worn hub

• Unplug the microwave or switch off the circuit breaker before service
• Remove the old tray; wipe the roller ring and cavity floor clean
• Inspect the center coupler and roller ring for wear; replace if damaged
• Align the new tray with the coupler so it sits flat and turns freely; test with a microwave-safe cup of water

This evaporator fan motor circulates cold air across the freezer evaporator and through the fridge, helping maintain even temperatures and proper cooling. Replaces a failed fan motor to restore airflow and reduce frost buildup. What it does:

• Spins the evaporator fan blade that moves cold air through the freezer and fresh-food compartments
• Restores airflow when the fan has stopped running or runs intermittently
• Helps prevent uneven cooling and excessive frost on the evaporator coil
• Can reduce unusual noise if the old motor is noisy or worn

• Disconnect power to the appliance before starting any repair
• Access typically requires removing interior freezer panels or back panels; use proper tools and keep fasteners organized
• Handle sharp sheet metal and insulated components carefully; wear gloves and eye protection

This is a metal mounting bracket that secures appliance components to the cabinet or frame, providing stable support and proper alignment. It's a direct-fit repair piece when the original bracket is bent, cracked, or missing. What it does:

• Provides a secure mounting point for panels or internal components to keep parts aligned and reduce vibration.
• Restores proper fit and clearance when a damaged bracket causes rubbing or misalignment.
• Helps maintain safe operation by keeping wiring, tubing, or assemblies supported.
• Fits in the original mounting location and uses existing fasteners for a straightforward replacement.

• One mounting bracket

• Use appropriate hand tools and retain original screws; replace any stripped fasteners.
• Disconnect power and water before beginning work.
• Align bracket to existing mounting holes; do not force or bend to fit.