Parts for Thermador PRSE366: Oven Cavity Parts

This Bake Element is an OEM part for Bosch ranges. It serves a role in generating heat for baking and cooking in the main oven cavity. Over time, continuous use and high temperatures can cause the bake element to wear out or fail.

Repeated heating and cooling cycles can lead to the bake element's deterioration. Physical damage or exposure to excessive heat can also cause it to malfunction.

Symptoms of a Bad Bake Element:

• Inconsistent oven heating
• Uneven cooking or baking
• Oven not reaching set temperatures

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Main broil heating element for the oven, designed to restore top-heat for broiling and browning. Replaces a failed broil element so the oven can produce even, high-intensity heat during broil cycles. What it does:

• Generates the high, direct heat at the top of the oven used for broiling and browning.
• Restores proper broil performance when the element no longer heats or glows.
• Fixes symptoms such as no broil heat, uneven browning, visible burn marks, or a broken/warped element.
• Works as the primary upper heating element used in broil cycles (main oven).

• Disconnect power to the range/oven at the breaker before starting any work.
• Remove oven racks and access the element from inside the oven; element typically secures with mounting screws and terminal connectors.
• Handle terminals and sharp metal edges carefully; wear gloves and eye protection.

This catalyst is a dishwasher replacement component that helps maintain cleaning performance by promoting proper detergent action during the wash cycle. Use when cleaning results decline or persistent film/spotting appears after runs. What it does:

• Promotes the chemical action of detergent for more effective soil removal
• Helps reduce cloudy film, spots, and residue left on dishes
• Works as part of the dishwasher's wash system to support normal cleaning cycles
• Fits into the appliance at the factory-designated location and interfaces with existing components

• Disconnect power (and water supply if required) before starting service
• Handle part carefully and reinstall using the original mounting hardware
• Do not modify the part; use only as designed to ensure proper function

This is a #10 x 1/2 inch pan-head Phillips sheet-metal screw used to fasten appliance panels and internal components. It replaces missing or worn screws to restore proper fit and reduce rattles or loose parts. What it does:

• Secures trim, access panels, brackets and other sheet-metal parts
• Keeps components aligned and prevents vibration-related noise
• Restores proper fastening when original screws are stripped, lost or corroded
• Works where a #10 x 1/2" pan-head Phillips sheet-metal screw is specified

• One #10 x 1/2" pan-head Phillips sheet-metal screw

• Disconnect power and water before servicing the appliance
• Use the correctly sized Phillips screwdriver to avoid stripping the head
• Start threads straight and tighten until snug—do not overtighten to avoid stripping or deforming sheet metal
• Keep small parts away from children and pets

This is a 1/4-20 hex keps nut — a hex nut with an attached captive washer that helps secure panels, brackets, and fasteners. It provides a simple, vibration-resistant fastening solution for appliance assemblies. What it does

• Fastens components to machine frames, panels, and brackets using a 1/4-20 bolt or stud.
• Captive washer helps resist loosening from vibration and movement.
• Commonly used where a compact, pre-assembled nut-and-washer is needed for reliable retention.
• Replace when threads are stripped, washer is damaged, or parts wobble or rattle.

• One hex keps nut (1/4-20).

• Disconnect power and follow appliance safety procedures before working on hardware.
• Use the correct 1/4" socket or wrench to install; hold the mating bolt head as needed to tighten.
• Tighten securely but avoid over-tightening to prevent thread damage or distortion.
• Replace with the same nut type and size to maintain fit and vibration resistance.

This part has been discontinued by the manufacturer and is no longer available.

This Tinnerman C nut is a spring-steel speed clip that secures sheet-metal panels and components using a mating screw. It provides a captive thread where a tapped hole or weld nut isn't practical, helping restore proper fit and stop rattles. What it does:

• Provides a captive, reusable threaded anchor for self-tapping or machine screws
• Secures trim, access panels and internal brackets to sheet-metal edges or panels
• Stops panel movement and vibration-related noise when the original clip is damaged or missing
• Works where a conventional nut or stud cannot be used due to limited access

• Disconnect power and unplug the appliance before accessing panels or fasteners
• Position the clip over the panel edge or hole, then press or slide until it snaps into place
• Align the mating screw and thread carefully to avoid cross-threading the clip
• Use hand tools or pliers for placement; do not over-torque the screw once installed

This 1/2-inch foam adhesive tape cushions and seals appliance gaps to reduce vibration and prevent rubbing or rattling of panels. It's a simple, flexible trim that restores fit and quiets noisy or loose parts. What it does:

• Provides a soft, compressible barrier to reduce panel-to-panel contact and eliminate rattles
• Helps seal small gaps to keep out dust and reduce drafts around doors or trim
• Cushions components to damp vibration and protect finishes from wear
• Conforms to irregular surfaces for easy placement in tight spots

• Access the area with the appliance powered off and, if applicable, unplugged for safety
• Clean and dry the surface before applying for best adhesion
• Cut to fit with scissors or a utility knife and press firmly to set the adhesive
• Replace if the foam is compressed, torn, or no longer adheres

Package of 60 pyramid shaped briquettes