Parts for Thermador PRSE366: Pallet Parts

The range leveling leg is an adjustable support foot located at each corner of the range that ensures the appliance sits level and stable. Replace when the leg is damaged, won't adjust properly, or the range rocks or tilts despite adjustment attempts.

Anti-tip bracket kit designed to secure your range to the wall or floor. Replaces broken, missing, or damaged brackets to prevent tipping hazards.

Relay terminal box housing for electric ranges. Encloses and protects electrical relay terminals. Replace if cracked, broken, or missing to restore coverage.

This is a door seal sleeve that fits around the perimeter of the oven door to create a tight seal between the door and the oven cavity. It helps retain heat inside the oven and prevents hot air from escaping during cooking or self-cleaning cycles. Replace this seal if you notice heat escaping around the oven door, uneven cooking temperatures, or visible damage such as cracking, hardening, or gaps in the seal material.

This high-limit thermostat is a safety device that monitors the oven's internal temperature and cuts power to the heating element if the temperature exceeds a safe threshold. It helps prevent overheating and potential fire hazards. Replace this part if your oven shuts off unexpectedly, fails to heat at all, or triggers error codes related to excessive temperature.

Support, hinge counter restores proper hinge support and door balance for a worn or damaged hinge assembly. This replacement helps the appliance door open and close smoothly and stay aligned for reliable everyday use. What it does:

• Provides structural support to the door hinge and helps counterbalance the door
• Stabilizes hinge movement to reduce sagging, binding, or uneven closing
• Helps the door latch and seal correctly by keeping the hinge alignment consistent
• Use when you notice door droop, difficulty latching, or irregular door motion

• Installation may require partial disassembly of the door or hinge assembly—refer to the OEM instructions for your model
• Disconnect power and turn off water supply before beginning any repair
• Inspect surrounding hinge components and fasteners; replace any damaged parts and test door operation after installation

Replace a cracked, broken, or missing latch cover plate on your electric range. This housing cover installs over the door latch mechanism for a complete finish.

This is a #10 x 1/2 inch pan-head Phillips sheet-metal screw used to fasten appliance panels and internal components. It replaces missing or worn screws to restore proper fit and reduce rattles or loose parts. What it does:

• Secures trim, access panels, brackets and other sheet-metal parts
• Keeps components aligned and prevents vibration-related noise
• Restores proper fastening when original screws are stripped, lost or corroded
• Works where a #10 x 1/2" pan-head Phillips sheet-metal screw is specified

• One #10 x 1/2" pan-head Phillips sheet-metal screw

• Disconnect power and water before servicing the appliance
• Use the correctly sized Phillips screwdriver to avoid stripping the head
• Start threads straight and tighten until snug—do not overtighten to avoid stripping or deforming sheet metal
• Keep small parts away from children and pets

Secures the glass cooktop to the range frame. Replace if clip is cracked, broken, or missing to properly hold the cooktop surface in place during use.

This is a 1/4-20 hex keps nut — a hex nut with an attached captive washer that helps secure panels, brackets, and fasteners. It provides a simple, vibration-resistant fastening solution for appliance assemblies. What it does

• Fastens components to machine frames, panels, and brackets using a 1/4-20 bolt or stud.
• Captive washer helps resist loosening from vibration and movement.
• Commonly used where a compact, pre-assembled nut-and-washer is needed for reliable retention.
• Replace when threads are stripped, washer is damaged, or parts wobble or rattle.

• One hex keps nut (1/4-20).

• Disconnect power and follow appliance safety procedures before working on hardware.
• Use the correct 1/4" socket or wrench to install; hold the mating bolt head as needed to tighten.
• Tighten securely but avoid over-tightening to prevent thread damage or distortion.
• Replace with the same nut type and size to maintain fit and vibration resistance.

This Tinnerman C nut is a spring-steel speed clip that secures sheet-metal panels and components using a mating screw. It provides a captive thread where a tapped hole or weld nut isn't practical, helping restore proper fit and stop rattles. What it does:

• Provides a captive, reusable threaded anchor for self-tapping or machine screws
• Secures trim, access panels and internal brackets to sheet-metal edges or panels
• Stops panel movement and vibration-related noise when the original clip is damaged or missing
• Works where a conventional nut or stud cannot be used due to limited access

• Disconnect power and unplug the appliance before accessing panels or fasteners
• Position the clip over the panel edge or hole, then press or slide until it snaps into place
• Align the mating screw and thread carefully to avoid cross-threading the clip
• Use hand tools or pliers for placement; do not over-torque the screw once installed

This part has been discontinued by the manufacturer and is no longer available.

This is an installation hardware set that includes the necessary mounting components for setting up a range or cooktop. It provides the brackets, fasteners, or clips needed for a secure and proper fit during initial installation or replacement. Use this set if original installation hardware is missing, damaged, or lost during a kitchen remodel.

Package of 60 pyramid shaped briquettes

Mounting screw for securing range components and panels. Replace worn, stripped, or missing screws during repairs or maintenance to ensure proper assembly.

90-degree elbow orifice holder for gas ranges and cooktops. Replace this gas line connector if cracked, broken, or causing improper gas flow alignment.

Foam adhesive tape seals gaps between range panels to reduce vibration and eliminate rattling. Replace when worn or loose. Verify fit with your model number.