Parts for Jenn-Air 21238: 06 - Oven Parts

The Bake Element is an OEM part for Whirlpool ranges. This heating element is responsible for providing the necessary heat for baking and roasting by distributing heat evenly throughout the oven cavity, ensuring consistent cooking results.

Over time, bake elements can wear out or fail due to regular use, exposure to high temperatures, or accidental damage during cleaning. 

Symptoms of a bad bake element include:

• Oven not heating to the set temperature
• Uneven cooking or baking results
• Visible signs of damage such as burns, blisters, or breaks in the element
• The element not glowing red when in use

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This broil element mounts at the top of the oven cavity and delivers the intense radiant heat needed for broiling. Replace a failed element to restore reliable top heat and consistent broil results in your range or wall oven.

• Provides strong, direct radiant heat from the top of the oven during the Broil cycle
• Common signs of failure: no broil heat, uneven broiling, visible breaks/blistering, or tripping the breaker when Broil is selected
• Restores proper broiling when the original element is open or shorted
• Also known as the upper/top oven element; verify fit with your model number

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the oven to cool completely and wear cut-resistant gloves
• Remove mounting screws, gently pull the element forward, and support the wires so they don't slip back through the liner
• Transfer wires one at a time to the new element, secure the element, check connections, restore power, and test

This 10-32 machine screw secures panels, brackets, and internal assemblies in your appliance. Replacing missing or stripped hardware restores a tight, rattle-free fit and helps keep components properly aligned.

• Provides a threaded fastener for metal-to-metal connections
• Helps maintain correct alignment of panels, brackets, and housings
• Replaces missing, rusted, or stripped screws
• Symptoms include loose or vibrating panels, gaps/misalignment, or hardware that won't tighten

• Disconnect power (and shut off gas/water, if applicable) before servicing
• Match the 10-32 thread and length to the original screw for the location
• Start by hand to avoid cross-threading; tighten snugly without over-torquing
• Retain and reinstall any original clips, spacers, or washers used in your model

This part has been discontinued by the manufacturer and is no longer available.

Color: Stainless steel

This part has been discontinued by the manufacturer and is no longer available.

This heating element warms the wash and rinse water and helps dry dishes at the end of the cycle. Replacing a failed element restores proper temperatures, cleaning performance, and drying so cycles finish as expected.

• Heats water to target temperature during wash and rinse phases
• Aids in drying by radiating heat into the tub at cycle end
• Controlled by the dishwasher's electronics to maintain proper heat
• Common symptoms of failure: water stays cool, poor drying, extended cycle times, or a visibly broken/burned element

• Disconnect power at the breaker and allow the dishwasher to cool before servicing
• Access is typically from inside the tub and/or beneath the unit after removing the toe panel
• Note wire positions, disconnect leads, remove retaining hardware, and carefully extract/install the element without bending it
• Ensure seals are correctly seated and tightened evenly; run a short cycle to check for leaks and heat

A single pop rivet used to secure sheet-metal parts and small brackets on appliances for a permanent, vibration-resistant hold. Replaces missing or damaged rivets to restore proper attachment without welding. What it does:

• Provides a permanent blind-rivet fastening point for panels, brackets and trim.
• Replaces rivets that are sheared, loose or missing and prevents rattling or misalignment.
• Ideal where a solid, tamper-resistant join is required and screws aren't suitable.
• Works with a compatible pop-rivet tool for quick installation.

• Drill out the old rivet carefully; use the proper size hole for the replacement rivet.
• Use a dedicated pop-rivet tool and wear eye protection during installation.