Bosch Refrigerator B36BT930NS Parts

Removes impurities from your refrigerator's water and ice supply. Replace every 6 months for clean, fresh-tasting water. Verify fit by model number.

Refrigerator door seal creates an airtight barrier to maintain internal temperature. Replace if cold air escapes or condensation forms. Confirm fit with model.

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

This sensor monitors operating conditions inside the appliance and reports to the control so cycles run correctly and safely. When the sensor fails, the control may receive inaccurate feedback, leading to irregular performance. What it does:

• Detects key conditions inside the appliance and sends a signal to the control
• Helps the control regulate heat and cycle progress
• Failure symptoms can include erratic cycle times, poor heating performance, or sensor-related error messages
• Can prevent the appliance from starting or completing a cycle if readings are out of range

• 1 sensor

• Disconnect power before servicing; shut off water supply if applicable
• Access the sensor and note wire orientation before removal
• Ensure any sealing surface is clean and the sensor is seated properly; check for leaks after reassembly where applicable
• Run a diagnostic or test cycle after installation to clear errors and verify operation

This perimeter door seal fits into the dishwasher tub channel along the sides and top of the door. It contains wash water and steam to help prevent front leaks and ensure proper door compression.

• Seals the gap between the door and tub on the sides and top
• Helps stop water drips at the front corners and along the door edge
• Reduces escaping steam and moisture at the door area
• Common signs of wear: leaks from the door, visible tears/flattening, musty odor, or the door not sealing smoothly

• Disconnect power and turn off the water supply before servicing
• Open the door, pull the old gasket straight out; clean the channel of debris and residue
• Find the midpoint of the new seal at the top center and press it evenly into the channel down both sides without stretching
• Close the door to help seat the seal, then run a test cycle and check for leaks

Secures components inside the freezer compartment. Replace if broken, cracked, or missing to keep parts properly positioned during door operation.

Small retaining clip that secures panels, trim, or covers inside your refrigerator. Replace when worn, broken, or missing to restore tight fit.

If ice builds up in your freezer or frost covers the evaporator coils, the defrost heater may have failed. This part melts accumulated ice periodically.

Secures shelves, door bins, and internal components in your bottom-mount refrigerator. Replace this clip if it's cracked, broken, or missing to restore stability.

Secures the water filter in your refrigerator for a snug, leak-free fit. Replace if lost during filter changes, cracked, damaged, or worn out over time.

This replacement rail supports a dishwasher rack and restores smooth, stable sliding for loading and unloading. It helps keep the rack aligned so dishes move in and out without catching or tilting. What it does:

• Provides a smooth track for the dishwasher rack to roll on
• Keeps the rack properly aligned to prevent binding or tipping
• Reduces noise and rough movement caused by a worn or damaged rail
• Replaces cracked, bent, or broken rails that stop the rack from sliding

• One replacement rail

• Disconnect power and water to the appliance before starting any repair
• Remove the affected rack before replacing the rail to access mounting points
• Inspect mounting clips or rollers and replace any that are damaged for proper fit
• Handle edges carefully and reassemble components securely; test rack movement after installation

If your refrigerator isn't making ice or produces hollow cubes, this ice maker assembly may need replacement. Moderate DIY repair restores ice production.

Factory mounting housing fixture that secures components inside your refrigerator. Replace if cracked, broken, or missing to restore proper support and alignment.

Mounting hardware kit secures refrigerator components in place. Replaces worn, missing, or damaged fasteners that cause rattling or loose parts inside unit.

This hinge pin secures the door hinge mechanism and allows your refrigerator or freezer door to pivot smoothly. It maintains proper door alignment and prevents the door from sagging or binding. Replace this part if your door won't close properly, sags when opened, or if you hear squeaking or grinding when opening the door.

Electronic power module for the dishwasher. This is the main control board that manages power and timing for wash, drain, and drying functions, helping restore normal operation when the original module has failed or is intermittent.

• Regulates incoming power and switches major loads (circulation pump, drain pump, heater, inlet valve)
• Coordinates cycle logic based on door and sensor inputs
• May help when the dishwasher won't power on or start a cycle
• May help when cycles stop mid-way, don't complete, or drying performance is poor

• Disconnect electrical power at the circuit breaker before servicing
• Access is typically from behind the lower toe panel/base; remove panels as needed
• Photograph and label wiring; transfer any mounting hardware; seat connectors fully
• Use ESD protection and handle the board by its edges only