Bosch Range HDI7132C Parts

The Sensor is an OEM part for Bosch ovens and ranges. It detects and monitors the actual interior temperature to maintain precise baking and roasting conditions.

Causes of a bad temperature sensor can include wear from prolonged heat exposure within the oven cavity. Physical damage, moisture intrusion or circuitry malfunctions may also lead to sensor failure over time.

Symptoms of a bad oven temperature sensor include:

• Inability to accurately read or achieve set target temperatures
• Fluctuations in readings displayed
• Cooking modes like bake and broil functioning abnormally

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Fix burners that won't light or spark continuously. This igniter electrode restores reliable gas ignition. DIY-friendly repair in about 15 minutes.

Replace your worn oven door gasket to restore a tight seal, prevent heat loss, and maintain consistent baking temperatures. Confirm fit with your model number.

This meat probe sensor is a temperature-sensing device that inserts into food while it cooks in the oven, allowing the oven to monitor the internal temperature and automatically stop cooking when the target temperature is reached. It connects to a jack inside the oven cavity via a heat-resistant cable. Replace this probe if your oven no longer reads the food temperature accurately, displays a probe error code, or if the cable or tip is visibly damaged.

This Terminal Box is an OEM part for Bosch Built-In Ovens. Integral to the oven's electrical system, this component serves as a secure connection point for various electrical wires within the appliance.

A common issue with a malfunctioning Terminal Box is loose connections or damage to the terminal block due to heat exposure or aging. 

Symptoms of a defective Terminal Box may include:

• Inconsistent power supply to the oven
• Non-functional heating elements
• Sparks or electrical arcing within the terminal box area

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This heating element is the direct-replacement heater assembly that provides the heat source for compatible appliances, restoring proper heating so cycles reach the temperatures needed for effective drying or cleaning. What it does:

• Generates heat for the appliance's thermal system (air or water heating depending on model).
• Replaces a failed or damaged heater element to restore normal temperature rise.
• Common symptoms it may fix: no heat, weak/no drying or cleaning performance, or unusually long cycles.
• Works as part of the appliance's safety and temperature-control circuit (thermostats or sensors may also be involved).

• Always disconnect power (and water, if applicable) before replacing the element.
• Allow the appliance to cool fully and wear protective gloves; heating elements can have sharp edges.
• After installation, restore power and run a short test cycle to check for any error codes.

Replace your worn, cracked, or missing range oven control knob. Restores smooth temperature selection and cooking function control with a precise fit.

Range overheating or shutting down unexpectedly? This cooling fan circulates air to maintain stable temperatures and protect internal components.

Leveling foot for electric and gas ranges. Adjustable metal foot installs at base corner. Replace if cracked, broken, or missing to level your range.

Restore oven visibility with this complete light assembly. Replace when bulb won't light, lens is cracked, or socket is damaged. Verify fit with your model.

Fix intermittent power or component failure with this range socket electrical connector. Restores secure wiring connections in electric and gas ranges.

This is the burner base housing for a gas range cooktop surface burner. It sits beneath the burner cap and distributes gas evenly to produce a consistent flame ring. Replace this part if you notice uneven flames, yellow or irregular burning, or if the base is cracked or corroded from spills and buildup.

This gas valve controls the flow of gas to an individual surface burner on a range cooktop. It connects to the burner control knob and regulates flame intensity from low to high settings. Replace this valve if a burner won't ignite, the flame is uneven or won't adjust properly, or you detect a gas smell around the cooktop controls.

Restore even baking when your oven heats unevenly. This convection fan blade circulates hot air for consistent cooking. Moderate DIY install.

Secures flexible hoses to fittings on your range to prevent leaks. Replace if connections are loose or clamp is damaged. Verify fit with your model.

Fix an oven door stuck closed after a cleaning cycle or error code 41. This door latch assembly restores normal lock/unlock operation on gas ranges.