Kenmore Ice Maker 106.89485991 (10689485991, 106 89485991) Parts

The Thermistor is an OEM part for Whirlpool Ice Machines. It monitors the temperature within the ice machine and sends readings to the control board to regulate the ice-making process.

Over time, the thermistor can become faulty due to electrical issues, normal wear and tear, or exposure to moisture. If the thermistor fails, it can lead to improper ice production or temperature regulation.

Symptoms of a bad ice machine thermistor include:

• Inconsistent ice production
• Ice machine not making ice at all
• Ice cubes that are too large or too small
• The ice machine running continuously or not cycling properly

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Ice Maker Water Line is an OEM part for Whirlpool refrigerators. It supplies water from the household plumbing to the ice maker, ensuring a consistent and reliable production of ice cubes. This kit includes a 1/4-inch plastic water line that is approximately 72 inches long. The tubing will need to be cut to match the desired length.

Causes of a bad water line can include wear and tear from prolonged use, kinks or bends restricting water flow, or leaks due to punctures or cracks. A compromised water line can result in inadequate ice production or water leaks.

Symptoms of a bad ice maker water line include:

• Reduced or no ice production
• Leaking water from the refrigerator
• Visible cracks or damage to the water line
• Ice cubes that are smaller than usual

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Adhesive is an OEM part for Whirlpool appliances, designed for securing and sealing various components within the appliances. This adhesive is ideal for use in situations where a durable and heat-resistant bond is necessary.Size: 2 oz. tube. This silicone rubber adhesive can be used on door gaskets, felt seals, and much more.

Over time, seals and insulation can become loose or detached due to wear, heat, or mechanical action, potentially compromising the appliance's functionality, efficiency, or safety.

The need for this adhesive may become apparent through symptoms such as:

• Loose seals or gaskets that result in heat loss, inefficiency, or the escape of moisture.
• Detached insulation leading to increased noise, heat transfer, or loss of energy efficiency.
• Components that have become unattached, affecting the appliance's performance or structural integrity.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Cutting Grid Kit is an OEM replacement part for Whirlpool ice machines. It cuts sheets of frozen ice into individual cubes, ensuring ice is available in uniform sizes. Each kit contains 8 screws and approximately 10 feet of wire. Two kits are required to replace both directions of the cutting grid to ensure comprehensive restoration of the ice maker’s functionality.

Causes of a bad Cutting Grid Kit can be attributed to mineral deposits buildup, which can obstruct the cutting process, electrical malfunctions affecting the heating element, or physical damage to the grid wires. 

Symptoms of a malfunctioning Cutting Grid Kit are:

• Ice sheets not being cut into cubes
• Accumulation of uncut ice in the bin
• The heating element fails to warm up
• Inconsistent ice cube sizes

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This cutter grid assembly uses heated wires to slice the ice slab into uniform cubes during harvest in clear ice machines. Replacing a damaged grid restores proper cube separation and helps prevent jams caused by uncut ice sheets. What it does:

• Heats and cuts the ice slab into individual cubes as it passes through the grid
• A failed or broken grid can leave the ice sheet uncut or in large fused blocks
• Visible signs can include broken/burned wires or cubes sticking together

• One cutter grid assembly

• Disconnect power and shut off water before servicing; allow the grid to cool
• Handle by the frame—do not touch or bend the heating wires
• Install in the same orientation; transfer existing mounting hardware if required
• Reconnect the harness securely and route wires away from moving parts

The Ice Machine Cleaner is an OEM replacement part for use with Whirlpool ice machines. This cleaner plays a crucial role in maintaining the efficiency and longevity of your ice machine, ensuring it continues to produce clear, taste-free, and odorless ice. Formulated to remove scale and mineral build-ups, this solution is essential for the regular maintenance of ice machines, which can suffer from lime scale deposits and other residues that affect ice quality and machine performance.

Symptoms of needing an Ice Machine Cleaner include:

• Reduced ice production efficiency.
• The appearance of scale and mineral deposits within the machine.
• Ice that tastes or smells unusual.
• Increased energy consumption as the machine works harder to produce ice.

Regular use of the Ice Machine Cleaner is vital to prevent the accumulation of minerals and scale that can lead to inefficient cooling and increased energy consumption. 

The Water Valve is an OEM part for Whirlpool ice machines. This part controls the flow of water into the ice maker, ensuring it receives the correct amount of water for ice production.  

Causes of a bad water valve can include wear and tear from regular use, mineral buildup from hard water, or electrical failures. 

Symptoms of a bad water valve include:

• The ice machine not producing ice
• Slow or inconsistent ice production
• Leaking water from the valve area
• No water entering the ice machine
• You should replace the water valve if it becomes faulty or damaged.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This replacement tube routes water safely between internal components. Use it to replace cracked, kinked, or brittle tubing so your appliance can restore proper water flow and reduce leaks during normal operation.

• Directs water between components to support normal operation
• Helps maintain consistent flow and leak-resistant connections
• Common failure signs: cracks, kinks, discoloration, or hardening
• Symptoms include water leaks, reduced flow, or intermittent filling

• Disconnect power and shut off the water supply before servicing
• Note original routing and fitting type; transfer any clips or ferrules if present
• Cut ends square and fully seat into push-to-connect or compression fittings
• Restore power and water; check all connections for leaks and proper flow

Size: 1/4 inch. Nut for plastic water line.

The Screw is an OEM part for Whirlpool refrigerators. This screw secures the refrigerator door hinge in place, allowing the door operates smoothly and seals properly. 

Over time, screws can become loose or go missing during repairs or adjustments, which can lead to a misaligned door, compromised sealing, and increased energy consumption. 

Symptoms of a bad screw include:

• The refrigerator door seems misaligned or does not close properly.
• Increased effort needed to open or close the door.
• Unusual gaps around the door seal when closed.
• The door might squeak or make other noises during operation.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This is an ice maker recirculation pump assembly. This part includes a motor and pump that sends water from the reservoir over the top of the evaporator plate. This forms the slab of ice that will then drop onto the cutting grid to make ice cubes.In the event that the appliance is not making ice, it could be because this part has gone bad. Some users report the pump becoming calcified and then no longer working. Whether this happens or not can depend upon the water quality. Unplug the appliance from the electrical outlet prior to attempting to replace this part. Wear work gloves for safety.This particular recirculation pump is compatible with ice cube makers that are manufactured by the Whirlpool, Kenmore, KitchenAid, and Scotsman brands. This part is sold individually and is sourced directly from the manufacturer.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:

• Thread-forming Type AB design engages thin metal or plastic components
• Secures panels, brackets, trim, or covers to reduce looseness and vibration
• Replaces missing, stripped, or corroded fasteners
• Helps maintain alignment for proper operation and reduced noise

• One screw

• Disconnect power before servicing; shut off water supply if working near water lines
• Use the correct driver for the screw head; start by hand to avoid cross-threading
• Tighten until snug—do not overtighten to prevent stripping or cracking plastic
• Repair damaged holes or replace worn clips/inserts before installing the new screw

• Size: #8-18 x 5/8 in (length 0.625 in)
• Thread type: Type AB, thread-forming

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

These inserts are for 1/4 inch plastic tubing. Package of 4.

This water reservoir tube routes chilled water from the refrigerator's internal reservoir to the dispenser line. Replacing a brittle, kinked, or cracked tube restores steady flow and helps stop leaks inside the fresh food compartment.

• Carries water between the reservoir and the dispenser supply path
• Maintains a sealed route to reduce internal leaks and air intrusion
• Damage or kinks can cause slow/no dispensing, intermittent flow, or water pooling near the crisper area
• Fresh tubing helps protect shelves and liners from water damage

• Disconnect power and shut off the household water supply before servicing
• Dispense water to relieve line pressure; place a towel/container to catch residual water
• Note original routing; avoid sharp bends and contact with moving or warm components
• Fully seat the tube into quick-connect fittings; tug gently to confirm it's locked