Kenmore Dryer 110.77087600 (11077087600, 110 77087600) Parts

• Will not tumble
• Noisy

Our Whirlpool Duet Sport Dryer, 6.7 cu. ft, Model WED8300SW0, bought new 8 years ago (2006), developed a VERY loud squeaking noise inside the dryer. Removing the top panel did not isolate the problem. I researched the problem and through the videos appearing on Appliance Parts Pros (APP) website and a few others, determined that the problem was either the drum belt, one or more of the 4 drum support rollers, or idler pulley or any combination of these. I ordered the kit to allow for... Read more

• Timer will not advance
• No heat or not enough heat
• Shuts off too soon
• Takes too long to dry

I'm starting with a quick background on my dryer. About 18 months ago the belt on the dryer started slipping and squealing. I had a can of belt dressing spray so I popped the top open and sprayed the belt. It actually worked for about a year before it started squealing again. For the next 6 months I had to spray it more and more often. Then the clothes stopped drying. Obviously, at this point, I had to get off my lazy ass and fix the dryer. Searched my dryer's model number on the internet and... Read more

• Too hot
• Shuts off too soon

I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more

• No heat or not enough heat
• Takes too long to dry

I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more

I watched videos on the disassembly of my dryer model, and got the model number hiding on the upper dryer door jamb. After calling AppliancePartsPros.com for help, then ordered parts with the help of APP. It took almost a full day to disassemble the dryer I have, as it is a little more complicated than some models, and I went very slowly on purpose to not lose screws, or break plastic parts. Getting the wiring harness apart was the hardest thing to do, as the screwdriver shown in the video... Read more

I am not an electrician, just a housewife with limited funds and a desire to DIY. I used the provided videos for knowing how to replace everything except the heating element which I just guessed based on other reviews and seeing how the other parts worked. Our dryer is 11 years old Whirlpool Gold HE and I have only ever cleaned the lint tray. My husband replaced the belt about five years ago and he did clean out the inside of the dryer. Started by ordering a thermal fuse because it was... Read more

• Shuts off too soon
• No heat or not enough heat
• Takes too long to dry

I used Fixya as an initial source describing my problem. I got two responses which were very helpful. One that the "coils" were probably the problem. Two, that the problem could be the thermostat or a thermistor in the dryer. I verified that AC was coming from the timing control, that both the two terminal and three terminal coils,the igniter and shut off thermostat all had continuity. I then applied AC directly to the coils: the two terminal coil ""clanked" and I interpreted that as the coil... Read more

I tried to hire someone through Home Advisor and was given an initial estimate of 436.00!?! However, no one ever contacted me about repairing the dryer. The washer and dryer are about 12 or 13 years old, so me and the wife discussed going to look at the alternative.... Buying a new washer and dryer set. We had planned on going on Dec 10th. I then decided to do some research on YouTube on Dec 8th for dryer repair and came across a video that was made by AppliancePartsPros.com. The video covered... Read more

• Will not tumble

I did a little research and found out that the dryer drum rollers needed to be replaced. I decided that since I would be replacing the 4 drum rollers that I should replace the belt and the belt drive pulley. This was a simple project thanks to YouTube. I used one of appliancepartspor videos to st me through the repair. Now I have a dryer that does not squeal like a pig! Read more

• No heat or not enough heat

I replaced the "heating element" which was bad.........as well as the "Thermst-fix" and "Thermal Cutoff" which are located on the side of the element mounting location while I had the dyer all opened up and the element mounting tube removed.......I also replaced the Dryer Thermister which is located on the top of the blower fan.....To get to these parts, you must open the top of the dryer which has spring latches on both sides of the front corners... they need to be pressed in (use a putty... Read more

• Takes too long to dry

My fiance was involved in a very nasty divorce where a very biased female judge forced him from his home for 14 months before he could take up residency again. He brought me back with him and I witnessed the grotesque damages she intentionally inflicted on his property. His washer and dryer are very expensive and high-end, as is the home and all his contents. One of the many damages she caused was that she had not cleaned the dryer lint filter in 14 months and the lint was a thick carpet which... Read more

• Door won't close

There is a video on youtube that talks about how to disassemble the electronic component out of the control board so I really won't go into that part of it. This disassembly of the control board will need to take place before you can even get started taking the gray piece out of the console to replace it. Be careful not break off the little tips behind the control knob, don't force it, it does come apart easily and there is an easy way to do it, that is also on youtube. This is where the... Read more

Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking. I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was... Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more

Replace the drum drive belt and tension pulley assy. Read more

Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them. Read more