Kenmore Washer 417.41100000 (41741100000, 417 41100000) Parts

The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.

This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

The Water Dispenser Valve is an OEM part for Frigidaire washing machines. This valve controls the flow of water into the washing machine during the wash and rinse cycles. It ensures that the correct amount of water enters the drum, contributing to efficient and effective cleaning.

Causes of a bad water dispenser valve can include mineral deposits or debris clogging the valve, wear and tear over time, or electrical faults that affect the valve’s operation. 

Symptoms of a bad water dispenser valve include:

• No water entering the washer
• Insufficient water during cycles
• Leaks around the valve area
• Inconsistent water flow

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Door Boot Seal is an OEM part for Frigidaire washing machines. It creates a watertight seal between the washer tub and the door, preventing water from leaking during the wash cycle.

Causes of a bad door boot seal can include wear and tear over time, mold or mildew buildup, and damage from sharp objects or improper cleaning methods. Exposure to harsh detergents or frequent overloading of the washer can also contribute to the deterioration of the seal.

Symptoms of a bad door boot seal include:

• Water leaking from the washer door
• Visible cracks, tears, or holes in the seal
• Mold or mildew buildup causing unpleasant odors
• Clothes coming out wetter than usual due to water leakage

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Drain Pump is an OEM replacement part for Frigidaire front load washers. Located inside the base of the washing machine tub, it actively pumps out water through the drain hose after each cycle completion. Efficient drainage is vital for preventing standing water issues.

Causes of a bad drain pump can include mineral or scale buildup within the pump chamber or impeller over time. The water valve may fail to open fully, blocking drain flow. Bearings may wear, causing the impeller to jam.

Symptoms of a bad drain pump are:

• Incomplete water draining after the cycle
• An accumulation of water remaining in the tub
• Leaking from the base
• Error codes could indicate drainage problems.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore.

The Water Level Pressure Switch is an OEM replacement part for Frigidaire washing machines. It senses the water level in the washer tub and signals to the control board when the tub is full. 

Symptoms of a faulty pressure switch include:

• The washer not filling or draining properly  
• No flow detection resulting in improperly filled or drained loads
• Unexpected or premature terminating of cycles
• Potential leaks from overfilling due to failed level sensing  

Causes can be normal wear over time exerting pressure on internal components, moisture exposure damaging electrical circuits, or impacts disrupting accurate pressure monitoring.

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. 

This clamp secures a flexible connection inside your appliance, holding a hose or boot firmly to its fitting to maintain a tight, leak-resistant seal and prevent connections from backing off during operation. What it does:

• Holds a hose or boot to a tub, pump, or port to keep the joint sealed
• Helps prevent leaks and disconnections from vibration or pressure changes
• Restores proper sealing when the original clamp is stretched, rusted, broken, or missing
• Typical symptoms include drips at the joint, a loose/slipping connection, or visible clamp damage

• 1 clamp

• Disconnect power and turn off water supply; place a towel to catch residual water
• Note the clamp's position before removal; seat the hose/boot fully over the fitting bead
• Position the clamp just behind the bead and engage/tighten it evenly
• Run a short test cycle and check the joint for leaks

The Tub to Pump Hose is an OEM replacement part for Frigidaire washing machines. This hose connects the tub to the pump, allowing water to be drained out of the tub and into the drainage system. 

Causes for a malfunctioning Tub to Pump Hose can include blockages from lint or small objects, cracks or holes in the hose material, or loosening of the hose clamps that secure it in place.

Symptoms of a bad Tub to Pump Hose include:

• Water leaking from the bottom of the machine
• Slow or incomplete drainage
• Unusual noises during the drain cycle
• Error messages related to water drainage

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Shock Absorber Mounting Pin is an OEM part for Frigidaire washing machines. It is a part that secures the shock absorber in place, ensuring proper absorption of vibrations and shocks during the washing cycle.

Causes of a bad shock absorber mounting pin can include loosening over time due to constant movement and vibrations, accidental damage or loss during repair or maintenance, or general wear and tear.

Symptoms of a bad or missing shock absorber mounting pin include:

• Excessive shaking or vibrating during the wash cycle
• Loud banging or rattling noises
• The washer moving or "walking" across the floor
• Premature wear or damage to the shock absorbers and other components

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This replacement spring restores the correct tension in the affected mechanism on your appliance, helping parts return smoothly and stay aligned. A fatigued or broken spring can cause loose action, noise, or improper engagement—this fixes it fast. What it does

• Provides return tension to the related mechanism so parts move and reset correctly
• Helps maintain alignment and reduces looseness or rattle during operation
• Supports smooth engagement/disengagement of linked components
• Common symptoms: weak/loose action, parts not returning to position, squeaking/rattling, visible break or deformation

• 1 spring

• Disconnect power; for gas appliances, shut off gas. For washers, also turn off water supply.
• Support the component under spring tension before removal to prevent sudden release.
• Note or photograph original routing and anchor points to match orientation on reassembly.
• Inspect related brackets/clips; replace any that are bent, worn, or corroded.

This rear shock absorber kit stabilizes the washer tub by damping movement and vibration. Replacing a worn shock restores smoother, quieter spins and helps prevent the drum from banging the cabinet or the machine from walking. What it does:

• Dampens tub movement to control vibration during wash and spin
• Helps prevent banging/thumping noises and cabinet contact
• Reduces "walking" or excessive shaking of the washer
• Can help minimize out-of-balance interruptions

• One rear shock absorber kit

• Disconnect power and turn off water before servicing
• Support the tub/drum to relieve load before removing the shock
• Remove retaining pins/bolts; install the new shock in the same orientation and transfer any reusable hardware
• For consistent damping, replacing shocks in pairs or as a complete set is commonly recommended

This washer drive belt links the motor to the drum pulley so the machine can tumble and spin. Replacing a broken or stretched belt restores smooth, reliable drum rotation during wash and spin cycles.

• Transfers motor power to the drum for tumbling and spin
• Worn or broken belts can cause no spin/tumble or intermittent rotation
• Common symptoms: drum won't spin, squealing or thumping noises, burning rubber smell, visible fraying/cracks
• Slipping belt can leave clothes wetter than normal at cycle end

• Disconnect power and turn off water supplies before servicing
• Access the belt from the rear or bottom; remove panels as directed in your model's service information
• Release belt tension at the motor/idler, remove the old belt, and route the new belt over the drum and motor pulleys with ribs properly seated
• Rotate the drum by hand to verify alignment; reassemble and test. Inspect the idler/tensioner and pulleys while open

This front shock absorber kit stabilizes the washer's tub during spin to reduce vibration and noise. Replacing worn dampers helps restore smooth operation and protects the cabinet and suspension from excessive movement.

• Dampens and controls tub movement during wash and spin
• Helps reduce shaking, "walking," and loud thumping/banging noises
• Can help when the washer won't reach or maintain full spin due to imbalance
• Replaces weakened or damaged front shock mounts/dampers

• Disconnect power and water before servicing
• Access shocks per your model's procedure; support the tub to relieve load
• Install with mounts aligned and fasteners tightened securely; verify free tub movement
• Many replace shocks in pairs to maintain balanced damping

This tub filter screens wash water as it leaves the outer tub, capturing lint and small items before they reach the drain pump. Replacing a damaged or missing filter helps restore proper draining and protect the pump from debris.

• Screens lint, threads, and small debris from water exiting the tub
• Helps prevent drain pump clogs and drain-related errors
• A clogged, damaged, or missing filter can cause slow/no drain, standing water, or pump noise
• Physical damage, broken tabs, or warping are common reasons to replace

• Disconnect power and turn off water; expect residual water—use towels or a pan
• Access location varies by model; the filter sits at the outer tub outlet along the drain path
• Release the hose clamp/retainer, remove debris and the old filter, seat the new filter fully in the port
• Reattach clamps securely and run a short drain/rinse to check for leaks and proper flow

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This O-Ring creates a tight, leak-resistant seal between appliance components. Replacing a worn or flattened ring restores proper sealing, helps stop drips at the joint, and protects nearby parts from moisture and mineral residue.

• Provides a compression seal between fittings, housings, or tubes
• Helps prevent water leaks and loss of pressure at the connection
• Common signs of failure: moisture or residue around the joint, visible cracks/flattening, leaks after reassembly
• Regular wear, heat, chemicals, or age can harden or deform the ring

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; lightly lubricate the new O-ring with food-grade silicone grease
• Seat evenly without twisting or pinching; reassemble and check for leaks