Kenmore Washer 417.44052500 (41744052500, 417 44052500) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: W10135699
The Affresh Washer Cleaner 3 Pack is an OEM cleaning accessory designed specifically for washing machines. This multipack contains 3 packets of a proven formula that helps eliminate odors from the washer tub, door, gasket, and drain areas. Regular cleaning is important to remove dirt, soap scum, mildew, and other residue that can build up over time and lead to odors. The Affresh tablets contain oxygen-powered enzymes and fresh scent boosters that are released during the cleaning cycle to safely and effectively eliminate musty smells.
This multipack of Green 4.2-ounce tablets ensures you have enough doses for consistent cleaning to keep your washer smelling fresh. As the #1 recommended washer cleaner brand, Affresh is also compatible for use in Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.
Do-It-Yourself Stories from Customers like You
Broken spider assembly; aka washer drum shaft assembly Jeff J. • Los Angeles , CA • November 01, 2015
I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point...
We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a...
Read more
More
$13.95
- Compare At:
-
$16.60
- You Save:
-
$2.65
Genuine Frigidaire part
By: Frigidaire
Part Number: 131763256
The Front Loading Washer Door Lock and Switch Assembly is an OEM part for Frigidaire washing machines. This component ensures that the washer door is securely locked during operation, preventing leaks and interruptions, and also communicates with the control board to allow the wash cycle to start.
Causes of a bad door lock and switch assembly can include wear and tear from regular use, damage from forced door opening, electrical failures within the locking mechanism, or issues with the switch contacts.
Symptoms of a bad door lock and switch assembly include:
- The washer door not locking or unlocking properly
- Error codes related to the door lock
- The washer not starting its cycle
- Interruptions in the wash cycle due to door lock failures
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
My washer would not complete the spin cycle and wring the water out of the clothes Lisa C. • Spring Lake , NC • March 12, 2014
I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely...
Read more
More
$113.95
- Compare At:
-
$136.74
- You Save:
-
$22.79
Genuine Frigidaire part
By: Frigidaire
Part Number: 137221600
The Frigidaire Drain Pump is an OEM part for Frigidaire washing machines. It plays a crucial role in the washer's operation by removing water from the wash tub at the end of each cycle, ensuring your clothes are properly drained before the spin cycle.
Causes of a bad drain pump can include blockages from debris such as coins, lint, or small items that escape from clothing, as well as motor or impeller damage. Electrical failures can also impair pump function, leading to inadequate water removal.
Symptoms of a bad Frigidaire Drain Pump include:
- Water not draining completely from the washer
- Unusual noises, like humming or buzzing, indicating the pump is struggling
- Washer stopping mid-cycle
- Water pooling around the base of the machine
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
My front loading washing machine would not drain. Meryl L. • Fort Thomas , AZ • October 26, 2020
So, Saturday, the washer wouldn't drain, yes, I tried the Drain/Spin cycle. So I took the clothes out, rinsed them out twice in the laundry sink and dried them. After a quick Google search, I came to the conclusion that the pump was bad and ordered a pump, $125.
Over the course of the next four days, expecting the new pump on Thursday, I baled out the washer, pulled it out from the wall and propped up the front (it's HEAVY), removed the front access panel, removed the drain inlet and outlet...
Read more
More
$152.95
- Compare At:
-
$183.54
- You Save:
-
$30.59
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304485917
The Shock Absorber Kit is an OEM part for Frigidaire washing machines. It is a comprehensive kit that includes 2 shock absorbers, 1 locking pin, 4 lock nuts, and a set of instructions. These shock absorbers play a vital role in reducing vibrations and absorbing shocks during the washing cycle, providing stability and minimizing excessive movement.
Causes of a bad shock absorber can include wear and tear over time, exposure to heavy loads or unbalanced loads that put excessive strain on the absorbers, or damage due to impact or mishandling.
Symptoms of a bad Shock Absorber include:
- Excessive shaking or vibrating during the wash cycle
- Loud banging noises
- The washer moving or walking during the operation
- Leaks due to increased stress on the tub and other components
This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
Do-It-Yourself Stories from Customers like You
Very noisy then ultimately bearing failure and a broken shock mount Brian B. • Canton , NY • September 23, 2014
I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the...
Read more
More
$46.95
- Compare At:
-
$55.87
- You Save:
-
$8.92
Genuine Frigidaire part
By: Frigidaire
Part Number: 134515300
The Door Boot Seal is an OEM part for Frigidaire washing machines. It is a flexible gasket that forms a seal between the washing machine door and the drum, preventing water from leaking during the wash cycle.
Causes of a bad door boot seal can include wear and tear over time, mold or mildew buildup, or physical damage from sharp objects or improper loading of the washer. Exposure to harsh cleaning chemicals can also degrade the seal, leading to leaks.
Symptoms of a bad door boot seal include:
- Water leaking from the front of the washing machine
- Visible tears or cracks in the seal
- Mold or mildew buildup on the seal
- A musty odor coming from the washing machine
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Very bad mold problem small water leak from door in front of washer unit Thomas R. • Portland , OR • November 05, 2020
Fixed by replacing the washer door seal "Bellows". Once again AppliancePartsPros comes through with the right part at a great price. It took quite some time to install because putting the inside spring back on the bellow was difficult so I needed to remove the top and front door of the washer to get better access. A set of 3 or 4 plumbing clamps are highly recommended to get that spring back on (I went to the store and bought some). If you search YouTube about replacing the bellows on your...
Read more
More
$148.21
- Compare At:
-
$224.01
- You Save:
-
$75.80
Genuine Frigidaire part
By: Frigidaire
Part Number: 134371220
The Water Inlet Valve is an OEM part for Frigidaire washing machines. This part controls the flow of hot and cold water into the washer's tub, ensuring the correct temperature mix for various wash cycles. By opening and closing at the command of the washer's control system, it plays a pivotal role in the machine's ability to execute programmed wash cycles with precision, affecting everything from the initial fill to the rinse phases.
Causes for the replacement of the water inlet valve can range from mineral deposits and sediment build-up, which can obstruct the valve's flow, to mechanical wear and electrical failures affecting the valve's operation.
Symptoms of a malfunctioning Water Inlet Valve include:
- The washer not filling with water
- Water entering the machine slowly
- The washer filling with the wrong water temperature
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
This part fixes the following symptoms
-
No hot or cold water
-
Will not stop filling with water
See more...
Do-It-Yourself Stories from Customers like You
The mixing valve that the water hoses attach to had frozen and broken. John M. • Commerce , TX • April 05, 2014
It was really easy to fix. I just took a screw driver and gently pried up on the top of the clothes washer to open up the top. Then the mixing valve was easy to access. I removed the two screws holding and unplugged the the wires. And pulled the old one free. Then reversed the process to install the old one. Less than thirty minutes start to finish.
Read more
More
$54.26
- Compare At:
-
$70.53
- You Save:
-
$16.27
Genuine Frigidaire part
By: Frigidaire
Part Number: 134527100
The Outer Bellow Clamp is an OEM Replacement Part designed for Frigidaire front-load washing machines. Its role is to securely hold the door boot in place, ensuring a tight seal that prevents leaks during operation. This clamp is attached to the front panel of the washer, and its installation requires the machine to be unplugged for safety.
Causes of a faulty outer bellow clamp can include wear and tear over time, damage due to excessive force or tension, or corrosion from exposure to water and detergent.
Symptoms of a bad outer bellow clamp may include:
- Water leaking from the washer door or around the door boot seal
- Loose or misaligned door boot seal
- Visible damage or deformation of the clamp
This clamp is compatible with select Frigidaire brand models including Crosley, Electrolux, Kenmore, and White Westinghouse.
Do-It-Yourself Stories from Customers like You
Replaced boot seal on front load washer (frigidaire) Diana Kiera G. • Austin , TX • January 24, 2015
Y'all! This video made fixing my washer easy peasy. The service repair man wanted $352! I paid less than $200 for the parts. I also called around and appliance parts pros was by far the cheapest option. The shipping was unbelievably fast. (Faster than my amazon prime!)
Read more
More
$45.95
- Compare At:
-
$54.68
- You Save:
-
$8.73
Genuine Frigidaire part
By: Frigidaire
Part Number: 134370000
The Detergent Drawer is an OEM part for Frigidaire washing machines. It holds and dispenses detergent at the appropriate times during wash cycles. The drawer is designed with compartments to separate powder and liquid detergents for optimized cleaning.
Causes of a bad detergent drawer can include leaks from cracks in the plastic material, malfunctions in the electronic components that control dispensing, or damage to the drawer itself.
Symptoms of a bad Detergent Drawer include:
- Incorrect or insufficient detergent amounts dispensed during cycles
- Residue, puddles, or leaks of detergent inside the washer tub or housing
- Odors or mold growth near the detergent area
- The drawer failing to open or close fully
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Detergent drawer broke Helen C. • Nashville , TN • November 26, 2016
Got online and searched for part by washer model number. Found AppliancePartsPro.com. They listed diagram of part. I ordered it online and received it next day with no extra charge for fast delivery. My husband attached cosmetic drawer cover to detergent drawer part we ordered in a few minutes. It fits and is working! Speedy service was appreciated.
Read more
More
$51.75
- Compare At:
-
$61.58
- You Save:
-
$9.83
Genuine Frigidaire part
By: Frigidaire
Part Number: 134743500
This is a motor control board for a washing machine. It comes with the board, tape, bracket, and screw mounted on control. In most cases, this part is located on the bottom of the appliance near the drive motor. The purpose is to control the speed of the drive motor. It also works to determine the direction of the tumble and spin actions while a cycle is in process. If the washing machine is pumping but does not spin, this is often the result of a malfunctioning motor control board.If the motor control board has gone bad, it should be replaced. To replace it, make sure the washer is unplugged or the circuit breaker has been turned off. Pull the washer away from the wall, remove the knobs from the front and screws from the back, and lift the control panel. This offers access to the motor control board, which should be removed so the new part can be installed.This motor control board is made for use with washing machines by Electrolux, Frigidaire, Crosley, and Kenmore. It is sold on an individual basis. This is an authentic OEM replacement part that is directly sourced from the manufacturer.
Do-It-Yourself Stories from Customers like You
E5b error code on frigidaire gallery front load washer Michael B. • Seattle , WA • October 26, 2015
This was the motor control board (also called the speed control board, motor control unit, or MCU in various places across the web). The repair was straightforward, except for two complications. First the old part was difficult to access in this model washer (Frigidaire Gallery Series front load washer). Instead of being easy to reach on the left side where there was space, it was sort of behind the actual motor on the right side of the housing. I spent some time trying to figure out...
Read more
More
$175.95
- Compare At:
-
$233.32
- You Save:
-
$57.37
Genuine Frigidaire part
By: Frigidaire
Part Number: 131268300
The Shock Absorber Mounting Pin is an OEM part for Frigidaire washing machines. It is a part that secures the shock absorber in place, ensuring proper absorption of vibrations and shocks during the washing cycle.
Causes of a bad shock absorber mounting pin can include loosening over time due to constant movement and vibrations, accidental damage or loss during repair or maintenance, or general wear and tear.
Symptoms of a bad or missing shock absorber mounting pin include:
- Excessive shaking or vibrating during the wash cycle
- Loud banging or rattling noises
- The washer moving or "walking" across the floor
- Premature wear or damage to the shock absorbers and other components
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Severe banging during spin cycle Vince V. • Benson , AZ • March 03, 2019
With more difficulty and frustration than expected but it works fine now.
Things learned:
1. Order only 3 replacement pins. One comes with the shocks that you can't be sure you see in the picture.
2. A circuit board in a plastic box mounted to the floor, left rear, must be removed by two screws to be able to get pliers onto the head of the pin more easily. This helps installation too.
3. A 1/2" deep socket pushed onto the retaining tab of the pin stays there while you pull with pliers from the...
Read more
More
$16.95
- Compare At:
-
$20.00
- You Save:
-
$3.05
Genuine Frigidaire part
By: Frigidaire
Part Number: 134365300
The Inner Bellow Spring Clamp is an OEM replacement part for Frigidaire front-loading washing machines. It anchors the interior bellow seal in the proper sealing position.
Causes of replacement include torsion fatigue from years of door opening/closing stresses. Mineral buildup may also restrict needed tension if left unchecked.
Symptoms consist of:
- Visible water leakage from the base of the washer door during active cycles
- Looseness permitting shifting or twisting of bellow position
- Inability to achieve proper water-tight integrity checks
This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore ranges.
Do-It-Yourself Stories from Customers like You
The front panel was broke due to pulling on it and not sliding the handle the front clamp rusted in two the bottom panel was rusted and the door boot seal looked terrible Daren R. • Garden City , GA • January 19, 2015
Watched the video a few times for door boot seal replacement. It was a lot of help! The spring is the hardest to replace and I did enlist the help of my wife. Everything went back on great. If you have to replace the front panel (with the buttons) be mindful that the buttons are spring loaded and will come out. I did not lose any and it went back together just fine. A little touch up paint on the washer and it all looks brand new and works great. And the parts came in quicker than...
Read more
More
$49.95
- Compare At:
-
$59.94
- You Save:
-
$9.99
Genuine Frigidaire part
By: Frigidaire
Part Number: 134455900
The Tub to Pump Hose is an OEM part for Frigidaire washing machines. This part directs water from the tub to the pump during the wash cycle. This flexible hose plays a role in the machine's ability to drain water efficiently after each wash or rinse cycle, ensuring optimal performance.
Causes for replacement might include wear and tear over time that leads to cracks or holes in the hose, blockages that prevent water from draining properly, or improper installation that results in leaks or water retention.
Symptoms of a bad Tub to Pump Hose include:
- Leaks found underneath the washing machine
- Problems with the washing machine draining properly
- Puddles of water appearing during or after a wash cycle
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Odor and mold Joel S. • Derry , NH • January 26, 2016
Our washing machine door boot seal was getting moldy and causing odor problems. Cleaning tablets and bleach weren't helping so it was time to be replaced. While I had the top and front off I changed all the hoses that could be collecting soap scum and mold, all other wetted parts were removed and washed. The video on the door boot seal, and inlet valve assembly were extremely helpful in understanding how these parts are removed and reassembled. Although the door boot seal is the most visible...
Read more
More
$57.22
- Compare At:
-
$67.52
- You Save:
-
$10.30
Genuine Frigidaire part
By: Frigidaire
Part Number: 131168200
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
- Fastens components to frames, brackets, and covers
- Replaces missing, damaged, or rusted screws
- Helps reduce looseness, vibration, and rattling noises
- Restores proper alignment of panels and assemblies
What's included: One screw
- Disconnect power before servicing; shut off gas/water if applicable
- Start the screw by hand to avoid cross-threading; use the proper driver
- Tighten snugly—do not overtighten to prevent stripping metal or plastic
Do-It-Yourself Stories from Customers like You
Grill on air duct had an item melt on to it and partially block air flow Charles C. • Orchard Park , NY • November 25, 2017
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube.
I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to...
Read more
More
$19.95
- Compare At:
-
$23.94
- You Save:
-
$3.99
Genuine Frigidaire part
By: Frigidaire
Part Number: 134372300
The Dispenser to Tub Hose is an OEM part for Frigidaire washing machines. This hose is responsible for transporting detergent and other cleaning agents from the dispenser to the tub during the wash cycle.
Common causes of a bad hose include constant exposure to water and detergent, which can lead to wear and tear, blockages from detergent buildup, or physical damage such as cracks and splits.
Symptoms of a bad dispenser to tub hose include:
- Water leaks near the detergent dispenser
- Uneven or insufficient distribution of detergent
- Visible cracks, splits, or other damage to the hose
- Error codes on the washing machine related to water flow
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Washer was leaking Carolyn S. • Venice , FL • December 05, 2016
First of all, I want to say that this is not the first time that I have used AppliancePartsPros. They give you everything you need in the most simplified manner to repair your appliances at home. I ran my washer until I started to see the leak coming from underneath. After verifying that the intake hoses, drain hose and pump were not leaking, I opened up the washer from the top by unscrewing the two screws on the back brackets and lifting up and out. Because the leak was displaying at the...
Read more
More
$54.26
- Compare At:
-
$65.11
- You Save:
-
$10.85
Genuine Frigidaire part
By: Frigidaire
Part Number: 131302800
This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.
- Fastens the drum baffle/lifter (vane) to the rotating drum
- Helps maintain proper tumble and load turnover
- Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
- Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes
What's included: One screw
- Disconnect power before servicing; shut off gas
- Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
- Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
- Start all screws before final tightening to seat the baffle evenly
Do-It-Yourself Stories from Customers like You
The pump hose had a tear in it and the water hoses were in bad shape Steven V. • El Cerrito , CA • September 21, 2014
Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy
Read more
More
$17.95
- Compare At:
-
$21.54
- You Save:
-
$3.59
Genuine Frigidaire part
By: Frigidaire
Part Number: 134370200
The Cover is an OEM part for Frigidaire washing machines. This cover marks the location and type of detergent, bleach, or fabric softener to be used, ensuring proper distribution during the wash cycle. It provides clear guidance for correct detergent placement, contributing to optimal washing performance.
Causes of a bad cover can include wear and tear over time, damage from harsh cleaning agents, or physical impact resulting in cracks or faded markings.
Symptoms of a bad dispenser drawer compartment cover include:
- Faded or illegible markings
- Detergent not dispensing correctly
- Leaks or spills around the dispenser area
- Visible cracks or damage to the cover
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Do-It-Yourself Stories from Customers like You
The washer's front drawer pull for the detergent and softener dispenser broke ! Paul F. • Chesterland , OH • December 22, 2017
After examining it, 2 of the 4 retainer clips had broken off. My wife grabbed her tablet, found Appliance Parts Pros website, saw 2 videos featuring our exact model of washer and ordered the 3 parts to replace broken and soon to fail parts !
Shipping was extremely fast !
Took out old assembly, replaced with new assembly in about 15-30 second, wife was happy, therefore I was happy !
Thx for being there !
Read more
More
$47.95
- Compare At:
-
$57.54
- You Save:
-
$9.59