Need Help?
Call
The Roller Kit is an OEM part for LG dryers. This 4 roller kit includes replacement drum support rollers, which are essential for allowing the dryer drum to rotate smoothly during operation. The rollers are designed to provide stable support for the drum, minimizing noise and ensuring efficient drying performance.
Over time, drum rollers can wear out due to continuous use, exposure to heavy loads, or lack of proper lubrication. When the rollers become damaged or worn, they may develop flat spots, lose their smooth surface, or begin to squeak. These issues can lead to improper drum rotation or increased strain on other dryer components.
Symptoms of a bad Roller Kit include:
This OEM LG part is also compatible with Sears/Kenmore.
I consulted with the internet and your website and determined I had a bad roller wheel. I was going to buy just one but determined if you have to take the thing apart, just replace all of them. These lasted 10 years after all. Opened up You Tube for the method to take the dryer apart. After doing the washer last year, I felt pretty bold and just ripped into the project. Within 30 minutes I had the drum out and located the problem wheel ( rear right side). It was locked up due to hair build up... Read more
The Dryer Blower Thermostat is an OEM replacement part for LG dryers. It plays a role in regulating the operation of the blower motor, which is responsible for circulating hot air throughout the dryer during the drying cycle.
Causes of a bad dryer blower thermostat can include electrical malfunctions, physical damage, or simply wear and tear over time.
Symptoms of a bad dryer blower thermostat include:
This OEM LG part is also compatible with Sears/Kenmore models.
Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more
Captures lint and debris during drying cycles. Replace when torn, cracked, or difficult to remove. Confirm fit using your dryer's model number.
I ordered a new part and it came very quickly. It was nice to have my dryer back working! Read more
Dryer not heating or overheating? The high limit thermostat shuts off heat at unsafe temperatures. Moderate difficulty repair requiring partial disassembly.
Dryer won't heat or takes too long to dry? A faulty igniter often causes no heat in gas dryers. Moderate DIY repair with front panel removal required.
I first ordered a thermostat and ignitor and replaced and that did not work. I asked Appliance Parts Pros their opinion in the chat and they said it was the coils in the gas valve but you had to replace the entire valve as the coils are not sold individually. So i ordered the part and also replaced the thermistor and drum belt while i had the dryer apart anyway! And this fixed the problem! These guys are the absolute best and most helpful i have ever dealt with. This is the second time i... Read more
Idler pulley maintains tension on the dryer belt. Replace if worn, cracked, or causing belt slippage. Installs between motor and drum support system.
I have an LG dryer purchased in 2007. Model: DLE9577SM. It was squeaking at start-up and rumbling a little. Not knowing what parts I would actually need, I ordered rollers with/without assemblies, tensioner pulley-only, new belt. After viewing this video a couple of times, I attacked my machine which is located in the comfort of my garage. Lots of room to spread out. Nice. This disassembly went OK however because, I suspect, my machine is 13 years old, the removal of the control panel was... Read more
This is a safety switch assembly that detects whether the dryer door is open or closed. It signals the control board to stop the drum and heating element when the door is opened during a cycle. Replace this switch if the dryer will not start, stops mid-cycle unexpectedly, or continues running with the door open.
Bought a new switch assembly, watched the video, and replaced the switch. Thr dryer now runs fine. Replacement part matched esxactly. Read more
This conversion kit includes the components needed to convert a natural gas dryer to operate on liquid propane (LP) gas. It typically contains replacement orifices and any necessary fittings to adjust the gas flow for LP fuel. Use this kit if you are switching your dryer's fuel source from natural gas to propane, such as when moving to a home without a natural gas supply.
Change orifice Read more
The Igniter Sensor is an OEM part for LG dryers. This sensor plays a critical role in the ignition process, ensuring that the gas ignites properly to produce the heat necessary for drying clothes efficiently. It helps monitor and regulate the ignition temperature.
Over time, the igniter sensor can become faulty due to regular use, exposure to high temperatures, or electrical issues. These factors can lead to a malfunction, resulting in the dryer not heating properly or failing to start.
Symptoms of a bad igniter sensor include:
Used video and took apart dru, this was extremely helpful. I bypassed the belt and door switch. Tested gas valves (gas disconnected) with multimeter. Found that the igniter worked the first gas valve, but the second gas valve would not open and the igniter would stay on. Found a flow chart online that shows the flame detect turns on causing the gas to turn on and shuts off the igniter. I replaced it and tested again. Igniter turns on, shuts off, then power to the second gas valve turns... Read more
Fix loud banging, grinding noise, or poor drying performance with a new dryer blower wheel. Restores proper airflow through drum and exhaust vent.
I replaced the dryer motor. I followed the repair video on the Appliance Parts Pro site, with a few modifications to the procedure. I loosened the control panel and flipped it forward to improve access to the wiring connectors. I also loosened the front panel and tipped it forward before disconnecting the door switch as there wasn't enough space to disconnect the switch otherwise. Removal of the blower assembly required the use of penetrating lubricant as the assembly was stuck on the motor... Read more
For propane order 383EEL3002A.
I ordered the natural gas conversion orifice with 2 day shipping, I also ordered for only maintenance reasons a new ignitor, as they are very common wear and tear item (like a spark plug on a gas engine or a glow plug on a diesel engine ). Both items came promptly and well protected . Easy install, only needed a Phillips screwdriver for entire repair. R&R top first, r&r front display panel,r&r door,r&r front panel,r&r drum (very easy), replaced ignitor and orifice. Total job took 30 min. I... Read more
This is the start button assembly that initiates the dryer cycle when pressed. It connects to the control panel and engages the dryer's motor circuit. Replace this button if it is stuck, broken, feels loose when pressed, or the dryer does not start when you push it.
Factory vent hose assembly for dryers. Installs between drum and exhaust port. Replace when hose is cracked, torn, disconnected, or missing.
This is a flat drying rack designed to sit inside the dryer drum. It provides a stable surface for drying items like shoes, stuffed animals, or delicate garments that should not tumble freely. Replace this rack if it is bent, broken, or has damaged supports that prevent it from sitting level inside the drum.
Replaced the Control Board. Read more
The Dryer Thermistor is an OEM part for LG dryers, designed to monitor and help regulate the temperature within the dryer by providing feedback to the control board about the temperature inside the drum. This allows the dryer to adjust its heat settings accordingly, preventing overheating and ensuring clothes are dried evenly and safely.
Symptoms of a bad Dryer Thermistor include:
Causes of a bad Dryer Thermistor can include a buildup of lint and debris affecting its ability to accurately sense temperature, wear and tear over time, or electrical issues within the dryer's circuitry.
This OEM LG part can also be used on Kenmore/Sears appliances.
Usually ships within 4 - 14 days
Dryer won't heat or stops mid-cycle? This gas burner valve assembly controls fuel flow to the igniter. Moderately challenging repair with basic tools.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.