Bosch Dishwasher SHE43P25UC Parts

Traps food debris and particles in your dishwasher sump. Replace when clogged with hard water deposits or buildup affects cleaning. Verify fit by model.

Restores proper door balance on your dishwasher. Replaces a worn, broken, or missing door hinge spring that causes sagging or doors that won't stay open.

Circular sealing gasket creating watertight joints between dishwasher components. Replace when flattened or cracked to prevent leaks. Confirm fit by model.

Seals the NTC temperature sensor port in your dishwasher to prevent leaks and ensure accurate temperature readings. Replace if leaking or worn. Verify fit with your model number before ordering.

Seals the aqua sensor assembly to prevent water leaks and protect electronics. Replace if you notice leaks or sensor errors. Confirm fit with your model.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

Spring-style hose clamp secures water hoses to prevent leaks at connections. Replace if worn, rusted, or if you notice dripping around hose fittings.

This tube channels water from the inlet valve to the wash system inside the dishwasher. It ensures a steady supply of water reaches the spray arms for proper cleaning during wash and rinse cycles. Replace if the tube is cracked, kinked, or leaking, which can cause poor water flow, inadequate cleaning, or water pooling under the dishwasher.

Replace cracked, broken, or missing dishwasher rack roller wheels. Snaps onto bottom or top rack to restore smooth gliding. Easy DIY installation.

Insulating pad for dishwasher door or tub. Replaces worn, torn, or missing insulation that affects noise dampening and heat retention.

Replace your dishwasher's cracked or broken control panel facia. This front-facing trim houses buttons and provides the user interface on your unit.

This is a trim strip that attaches along the lower portion of the dishwasher door. It helps seal the door edge and provides a finished appearance to the front panel. Replace this piece if it is cracked, warped, or missing, which can lead to water leaks around the bottom of the door during wash cycles.

Tall item spray head that attaches to the upper feed tube in your dishwasher. Replace if cracked, broken, missing, or won't lock into place properly.

This replacement switch restores reliable electrical control within your appliance. It opens and closes an electrical circuit to signal the control system, so power and functions respond consistently when the switch is actuated.

• Opens/closes an electrical circuit when the actuator is engaged
• Sends an on/off or selection signal to the control or main board
• Helps address: no response or no start, intermittent operation, stuck on/off state, or heat-damaged/burned terminals
• Direct replacement for the original switch on applicable units

• Disconnect power at the breaker and unplug the unit before servicing
• Access the control area to reach the switch; note wire locations or take a photo
• Transfer wires one at a time for correct orientation; ensure snug terminal connections
• Reinstall mounting hardware, reassemble panels, restore power, and test operation

Secures hoses to fittings and prevents leaks in your dishwasher. Replace if stretched, corroded, or damaged to maintain a tight seal. Confirm fit.