Bosch Dishwasher SHV09T33EU Parts

Traps food particles and debris during wash cycles to keep water clean. Replace if clogged with buildup or if plastic retainer fails. Verify fit by model.

Seals the detergent dispenser to prevent leaks and ensure proper release during wash cycles. Replace if detergent leaks or dispenser malfunctions.

2 clamps included.

Fix dishwasher not heating or running for hours. This NTC temperature sensor monitors water temp and prevents overheating. Moderate DIY repair with video.

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

O-ring seal prevents leaks between dishwasher components. Replace when you notice water drips or moisture buildup. Confirm fit with your model number.

The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.

Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.

Symptoms of a bad float include:

• The dishwasher not filling or filling slowly
• Error codes related to fill issues
• Improper water levels impacting wash results

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

Replacement silverware basket with handle for dishwasher lower rack. Holds utensils upright for better cleaning. Replaces cracked, broken, or missing baskets.

Dishwasher indicator light not working or staying on? This light signals cycle status and alerts. Common fix for control panel display issues.

Circular sealing gasket creating watertight joints between dishwasher components. Replace when flattened or cracked to prevent leaks. Confirm fit by model.

Seals the NTC temperature sensor port in your dishwasher to prevent leaks and ensure accurate temperature readings. Replace if leaking or worn. Verify fit with your model number before ordering.

Seals the aqua sensor assembly to prevent water leaks and protect electronics. Replace if you notice leaks or sensor errors. Confirm fit with your model.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

The Tube Dishwasher is an OEM component for Bosch dishwashers. It is responsible for circulating water throughout critical spray arms during different cycles. 

Causes of a bad tube dishwasher can include mineral buildup reducing the tube diameter over time, physical damage from scraping dishware against the pipes, or wear from normal vibration/motion.

Symptoms of a bad tube dishwasher include:

• Incomplete spray coverage in hard-to-reach areas  
• Soft or spotty cleaning performance in certain sections
• Puddles or leaks at the tube installation points
• Dirty or stagnant water unable to circulate properly

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.