Bosch Dishwasher SHV09T33EU Parts

Very smooth. I ordered the door and the control panel. It is helpful to have an extra set of hands when removing the screws from the door or place something under it so it doesn’t drop. The door comes off with about 10 screws. They are different length. Short screws go into steel, long go into plastic. Remove the door and upper facia/control panel. You’ll need to disconnect the wires. The panel has two parts that need to be transferred. 1. The electronic panel. It’s white and has a row of... Read more

We replaced the black door seal gasket around the front of the dishwasher. The old black seal gasket had begun to deteriorate, every time it was touched black stuff would rub off onto hands and onto utensils in the upper basket. We wore some disposable gloves to remove the old seal to avoid getting the black stuff on our hands. Before entirely removing the old seal gasket we studied its placement to tell which way the new seal gasket should be placed. We didn’t want to place the seal gasket... Read more

I bought the door and bottom seal and was already to go. Appliance Pro got the parts to me in 2 days. I read an article that said if the spray arm holes are blocked that this could cause a wave in the dishwasher that could cause the water to fly up to the inlet used for drying and the water could run down between the front and inside door appearing to be a leak. I checked and my spray arms were indeed blocked. I pulled them out, cleaned them up, reinstalled, and low and behold that was appeared... Read more

I changed the control board (00498022) in the door of my Thermador dishwasher. Thermador, Bosch, and Siemens all use the same board for the indoor controls and display. This required a #15-star head driver to remove the screws. I used an impact wrench (set to a low torq setting) to speed things up. There are approximately 12 screws to remove. Two are long. The rest are short. Be careful to hold the door together as the last screws are removed. Everything comes apart easily and you do not... Read more

• Won't start

Replaced with new latch, took about 5 minutes. T25 torx screwdriver and flathead screwdriver needed. Read more

• Leaking

Ordered replacement drain hose, left hand panel of dishwasher removed (remove 2 screws in front left trim panel & friction fit clip at top back then slide up & off. This reveals the O-ring drain hose connection point. You need to remove the retainer block where the hose exits the appliance. Old hose pulls out and new hose pushes in. In the end a very easy installation. Most of the time spoent here is removal & reinstallation of dishwasher back into position - the actual hose swap takes 10 mins Read more

Checked out the AppliancePartsPros.com online parts/assembly diagrams for our Bosch dishwasher model and ordered the two sided set of new springs + connector ropes + connector-to-door ... plus a couple of other relatively inexpensive adjoining parts that might have become worn over time, just in case they were needed. The extra parts arrived in two days with standard shipping. Called about the "back ordered" primary set of parts (which had been listed as being "in stock" when I placed the... Read more

On my Bosch she55m15uc/64, the cycle would take 3-4 hours, with the machine stuck on "1 minute" for a long time. The interior was getting moldy and smelly, and the dishes had a white film. At first, I thought it was the heater relay on the control board, but I pulled that relay and it seemed to be working. I could get an ohmmeter on the heater element without taking the bottom off the dishwasher, and the resistance was infinite. Replacing the heater did the trick. On my unit there was a... Read more

• overflowing
• Will not fill with water

I checked continuity at the float switch since I knew the inlet valve was working when direct wired to 120v. Switch did not have continuity. Replaced switch and inlet valve worked at start of cycle. Read more

Easily installed the side mounts and put new trim around the opening. Read more

Used vids on youtube for steps on how to disassemble and install the pump; search "Bosch dishwasher circulation pump replacement". Also on AppliancePartsPro forums, a poster put up the Bosch "Dishwasher Service Training Manual" in .pdf. Search "Bosch dishwasher low pressure" on the forum. It's one of the post with the longest thread. Six pointers. 1. In another forum post, the poster noted that some hoses were brittle with age - and cracked when reinstalling. I had same issue (my washer is... Read more

This turned out to be a major effort, requiring me to disconnect the dishwasher, pull it from the cabinetry and partially disassemble the dishwasher to replace the door closer pulley Read more

Hearing a metal on metal noise and not actually circulate water cancelling cycle worked fine After some web research, I concluded it was highly likely to be the circulation pump, so I watched the video on AppliancePartPros.com and realized it was a lengthy repair (a lot of steps) but not technically difficult. I simply played and paused the video at each step and duplicated the steps. The biggest things to take note of: 1) take good pictures of the wiring to use when you re-connect. 2) Wear... Read more

It went well, thanks, Read more

I replaced the gaskets with products from this site which I would not have been able to do without the video on this site. Hard job. The leak was still there though, so I have some hints with this kind of washer. 1) There is a float switch on the base that turns on the drain pump when there is a leak, that is why the drain pump runs constantly, it prevents catastrophic flooding in many cases. The float consists of a little styrofoam donut that lifts an arm, all white. The arm is connected to a... Read more

Dishes were not getting clean, I tried cleaning the original arms but after a number of tries I just wanted clean arms. Changing arms was extremely easy and the dishes are getting amazingly clean! Read more