Bosch Dishwasher SHV4ATB3UC Parts

Replacement mounting bracket for dishwashers. Secures unit to countertops and cabinetry. Replace if bracket is cracked, broken, or missing from installation.

Replacement screw for dishwashers. Secures panels and internal components. Needed when original is stripped, missing, or damaged during repairs.

The Water Inlet Fill Hose is an OEM part for Bosch dishwashers. This part is responsible for safely and efficiently connecting the dishwasher to your home's water supply, ensuring that water flows into the dishwasher at the correct pressure and volume for optimal cleaning performance. 

Over time, the Water Inlet Fill Hose can become susceptible to wear and tear, leaks and blockages.

Symptoms indicating the need for a new Water Inlet Fill Hose include:

• Water pooling around the dishwasher base, pointing to a potential leak in the hose.
• The dishwasher not filling with water properly, or filling very slowly, suggesting a blockage or damage to the hose.
• A visible inspection reveals cracks, bulges, or signs of corrosion on the hose connectors.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The pump sump seal repair kit contains gaskets and seals that prevent water leaks in the dishwasher's drain pump assembly. Located at the bottom of the dishwasher tub where the pump connects, these seals maintain watertight connections. Replace if you notice water pooling under the dishwasher, reduced drainage performance, or visible water leaks during operation.

Secures panels, brackets, and trim pieces inside your dishwasher. Replace this fastener if stripped, missing, or damaged to restore tight assembly.

Fix a dishwasher that won't start, stops mid-cycle, or has error codes with this pre-programmed power module control board. Manages all wash functions.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

Replace your dishwasher's thermal insulation if experiencing excessive heat around the unit or noise during cycles. Protective barrier for safer operation.

Vent hose for dishwashers that guides steam and moisture out during wash cycles. Replace if cracked, disconnected, or worn to restore proper venting.

This sensor monitors the clarity and cleanliness of the wash water inside the dishwasher, helping the control board determine how dirty the water is and whether additional wash cycles are needed. It plays a key role in optimizing water usage and ensuring dishes come out clean. Replace this sensor if dishes are consistently coming out dirty, wash cycles are running too long or too short, or the dishwasher is not properly adjusting its cleaning performance.

Replacement tube for Bosch appliances that routes water or drainage between components, helping restore correct flow, reduce pooling and leaks, and maintain normal appliance performance. What it does:

• Channels water between valves, pump and drain to enable normal water movement.
• Replaces cracked, split or blocked tubing that can cause leaks or standing water.
• Helps restore proper drainage and prevent water from pooling inside or under the appliance.

• Always disconnect power and shut off the water supply before servicing the appliance.
• Inspect and replace any damaged clamps, seals or fittings when installing the tube.
• Route the tube exactly as the original to avoid kinks; secure with the factory clamps or equivalent.

This replacement spring restores proper tension in the specific mechanism it supports, helping the connected component operate smoothly. A worn or broken spring can cause weak action, poor latching, or parts that won't return or stay in position.

• Provides controlled tension/return force for moving parts per your model's design
• Helps doors, lids, latches, or dispenser mechanisms open/close or release reliably
• Symptoms of failure can include weak or uneven tension, components not staying shut/open, or sluggish operation
• Replace if the spring is stretched, broken, deformed, corroded, or missing

• Disconnect power and shut off water supply before servicing
• Note the spring's orientation and anchor points; take a photo for reference
• Use needle-nose pliers for removal/installation and avoid over-stretching
• If your model uses paired springs, replace both to maintain balanced tension

This factory screw secures appliance components per the original design, helping stop looseness and vibration. Replace a missing, stripped, or corroded fastener to restore a solid, rattle-free fit and protect nearby parts from damage.

• Secures panels, brackets, or internal components as specified by the manufacturer
• Helps maintain proper alignment and reduces vibration or rattling
• Replace if the head is stripped, threads are damaged, or the screw is missing
• Common signs include loose or misaligned panels/trim and hardware that won't stay tight

• Disconnect power and turn off water or gas supply as applicable before servicing
• Match length and thread to the original; start by hand to avoid cross-threading
• Use the correct driver bit and tighten snugly without overtightening
• Retain any original washers, bushings, or clips used in the assembly

This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.

• Fastens covers, panels, and brackets to their mounting points
• Helps maintain alignment of the attached component
• Reduces movement that can cause noise or wear
• Typical reasons to replace: missing screw, stripped head/threads, loose panel or bracket

• Disconnect power and, if applicable, shut off water before servicing
• Use the driver bit specified for your model; hand start threads to avoid cross-threading
• Tighten snugly without over-torquing to prevent stripping
• Replace screws one at a time to maintain alignment

Replace a broken, worn, or missing dishwasher leveling leg. This adjustable foot installs at the front corner to stabilize and level your appliance.

Dishwasher indicator light not working or staying on? This light signals cycle status and alerts. Common fix for control panel display issues.