Bosch Dishwasher SHX98M05UC Parts

Fix a dishwasher that won't fill, overfills, or leaks from the base. Water inlet valve controls flow into the tub. Moderate DIY repair, 30-45 minutes.

O-ring seal prevents leaks between dishwasher components. Replace when you notice water drips or moisture buildup. Confirm fit with your model number.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.

• Provides a finished edge along the upper portion of the door/face area
• Helps protect adjacent components from dust and minor splashes
• Maintains proper panel gaps and alignment
• Typical symptoms: visible cracks, warping, looseness, rattling, or exposed/sharp edges

• Disconnect power before servicing; also shut off water
• Remove the existing strip by releasing screws/clips; retain hardware for reuse
• Align the new strip and secure evenly—do not overtighten fasteners
• Check door/panel operation afterward to confirm proper fit and clearance

The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.

Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.

Symptoms of a bad float include:

• The dishwasher not filling or filling slowly
• Error codes related to fill issues
• Improper water levels impacting wash results

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Wax motor for detergent/rinse-aid dispenser.

Detergent not dispensing during wash cycle? This actuator arm with spring releases the detergent cup at the right time. Moderate DIY repair.

This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.

• Fastens covers, panels, and brackets to their mounting points
• Helps maintain alignment of the attached component
• Reduces movement that can cause noise or wear
• Typical reasons to replace: missing screw, stripped head/threads, loose panel or bracket

• Disconnect power and, if applicable, shut off water before servicing
• Use the driver bit specified for your model; hand start threads to avoid cross-threading
• Tighten snugly without over-torquing to prevent stripping
• Replace screws one at a time to maintain alignment

Single Torx T20 screw secures dishwasher panels, brackets, and trim. Replace missing, stripped, or damaged fasteners to keep components tight.

Black adapter connects dishwasher drain hose to another hose or fitting for secure wastewater routing. Replace when cracked, loose, or missing for leak-free.

Dishwasher indicator light not working or staying on? This light signals cycle status and alerts. Common fix for control panel display issues.

Seals the NTC temperature sensor port in your dishwasher to prevent leaks and ensure accurate temperature readings. Replace if leaking or worn. Verify fit with your model number before ordering.

Circular sealing gasket creating watertight joints between dishwasher components. Replace when flattened or cracked to prevent leaks. Confirm fit by model.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Seals the aqua sensor assembly to prevent water leaks and protect electronics. Replace if you notice leaks or sensor errors. Confirm fit with your model.

The Impeller Jug is an OEM part for Bosch dishwashers. Located inside the wash chamber, the impeller jug is responsible for evenly distributing water throughout the dish rack during the wash cycle. It features strategically placed holes and channels that work with the spray arms to direct water flow and ensure all dishes receive thorough coverage. 

Symptoms of a bad impeller jug include:

• Incomplete cleaning even on short or heavy wash cycles  
• Dirty dishes remaining at the end of the cycle
• A buildup of food or grime deposits inside the wash chamber
• Off-balanced or excessive noise levels during washing

Causes of failure can be mineral or scale buildup inhibiting water flow, cracked or damaged casing allowing leaks, or worn impeller fins no longer efficiently dispersing water. Over time, hard water deposits and normal use can degrade performance. 

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers.