Bosch WTA3510 UC/13 (FD 8111-) Parts

This door gasket is the flexible rubber seal that fits the dishwasher door to keep water inside the tub during cycles. Replacing a worn gasket restores a watertight seal and helps stop leaks and moisture buildup. What it does:

• Seals the gap between the door and tub to prevent water leaks during wash cycles
• Keeps spray and suds inside the dishwasher, protecting surrounding flooring and cabinetry
• Helps reduce odors and mold growth by maintaining a tight seal that limits moisture escape
• Common symptom: water pooling or dripping from the bottom/side of the door
• Common symptom: visible cracks, tears, flattening, or hardened areas in the gasket

• One door gasket

• Inspect the door channel and mating surfaces; clean away residue before installing the new gasket
• Press the gasket evenly into the door channel, working from one end to the other to avoid twisting
• Turn off power and water to the appliance before working on the door; refer to the service manual for model-specific instructions

This bearing set replaces worn drum bearings to restore smooth, quiet rotation and help prevent further damage to the tub assembly. Fits select Bosch WTA/WTL laundry machines. What it does

• Supports the drum/tub shaft so the drum turns smoothly and quietly.
• Worn bearings can cause loud squealing, grinding, or metal-on-metal noise.
• Excessive vibration or a wobbling drum during spin are common signs of bearing failure.
• Replacing the bearing set helps prevent additional wear to the drum and shaft.

• Disconnect power and water before beginning any repair.
• Access requires drum/tub disassembly; keep track of fasteners and seals.
• Bearings are typically press-fit; removal and installation may require a bearing puller/press or specialized tools.

This high-limit thermostat is the overheat safety switch for the heating circuit. It opens when excessive temperature is detected to cut power to the heater, protecting the appliance and restoring normal heating when replaced.

• Monitors temperature at the heater and opens the circuit if it overheats
• Helps prevent damage from excessive heat and potential safety hazards
• A failed-open thermostat may cause no heat, poor drying, or unusually long cycles
• Frequent tripping may point to underlying circulation or control issues that should be checked

• Disconnect power at the breaker or unplug the appliance; allow it to cool completely before service
• Access location per model; typically mounted on or near the heater or heater housing
• Note wire positions and transfer leads one at a time; secure using existing mounting hardware
• After installation, run a test cycle to confirm proper heating

This thermostat with attached sensing cable detects and regulates appliance temperature to help maintain proper heating cycles and protect against overheating. It replaces a failed temperature control component so your appliance can heat correctly and safely. What it does:

• Senses internal temperature and sends a signal to the control to start or stop heating
• Helps prevent overheating by providing accurate temperature feedback
• Works as the temperature-sensing element used by the appliance control board

• Disconnect power before servicing to avoid electric shock
• Handle the sensing cable and probe gently; do not kink or pinch the capillary/sensor
• Verify proper routing and secure mounting of the sensor per the appliance's service instructions

A sealing kit designed to replace worn seals in the dishwasher pump area to stop leaks and restore a watertight pump assembly. Ideal when seals fail and allow water to escape around the pump. What it does:

• Replaces worn or damaged pump seals to help stop leaks beneath the machine
• Restores the pump assembly's watertight seal for proper water circulation and drainage
• Helps prevent water damage to the cabinet and flooring caused by seal failure
• Commonly used when you find water under the dishwasher, visible leaks near the pump, or damp cabinet flooring

• One sealing kit

• Disconnect power and shut off the water supply before starting any repair
• Access usually requires removing the lower access panel and may require partial pump disassembly
• Keep track of small seals and O-rings during removal; inspect related parts for wear

This door latch mechanism secures the appliance door and completes the door-switch circuit so the unit can operate. It replaces a worn or damaged latch to restore proper door closure and reliable operation. What it does:

• Engages and holds the door closed during cycles so the appliance can run.
• Activates the door switch/contact that signals the control board the door is closed.
• Commonly used when the door won't stay closed, the appliance won't start, or the latch feels loose or broken.
• Fits into the door frame and mates with the striker/handle to keep the seal tight.

• One door latch mechanism

• Disconnect power (unplug or switch off breaker) before servicing to avoid electrical shock.
• Access usually requires opening the door panel or removing the inner door; keep track of screws and clips.
• Handle carefully to avoid damaging the latch tabs or wiring; test door operation before reassembling fully.
• If wiring or mounting points are damaged, replace those parts as needed rather than forcing the latch.

This replacement cable restores a reliable electrical connection between appliance controls and components to help eliminate intermittent operation or loss of function. It's a direct-fit part used where the original wiring is damaged or worn. What it does:

• Carries power or control signals between internal components to enable proper operation
• Replaces frayed, damaged, or broken wiring that can cause intermittent faults or component failure
• Helps restore functionality such as control responsiveness, motor/start signals, or sensor communication
• Prevents arcing or shorting that can occur with compromised insulation or connectors

• Disconnect the appliance from power before inspecting or replacing the cable
• Verify connector orientation and routing to avoid interference with moving parts
• Use only proper connectors; do not use temporary splices that can loosen or overheat

This clear replacement lens protects and covers an internal appliance light while restoring proper light dispersion and appearance. It replaces a cracked, cloudy, or missing lens to improve interior visibility and finish. What it does:

• Covers and protects the internal light bulb or LED assembly from debris and moisture.
• Restores even light dispersion for brighter, clearer interior illumination.
• Replaces cracked, chipped, or discolored lenses that cause glare or reduced visibility.
• Helps maintain original appearance and prevents direct contact with the light source.

• Disconnect power to the appliance before any service to avoid electrical shock.
• Handle the lens carefully to avoid scratching; align retaining tabs or slots before snapping into place.
• Use only the factory fasteners or clips; do not overtighten or force the lens into position.

A small metal clip that secures the dryer to the top of the washer when stacking, keeping the pair stable during operation. Use this replacement clip if the original is bent, missing, or fails to hold the units together. What it does:

• Locks the dryer cabinet to the washer top to help prevent shifting or sliding during use
• Restores the mechanical fastening point used in factory stacking setups
• Common symptom: dryer feels loose or moves when the pair operate together
• Common symptom: visible bent, cracked, or missing clip at the stack connection

• Turn off and unplug both appliances before attempting installation
• Lift and support the dryer securely during alignment; use a second person or proper lifting equipment
• Slide or snap clip into the factory stacking locations per the appliance's service instructions