Bosch Dryer WVT1260EE Parts

Secures the door boot seal to the washer front panel, preventing leaks. Replace if broken or when installing a new door seal for proper fit.

The Carbon brush, drum motor is an OEM part for Bosch washing machines. These carbon brushes are responsible for transferring electrical current from the commutator on the motor to power the rotary movement inside the washing machine drum.  Two come per package.

Symptoms of a bad carbon brush, or drum motor can include:

• noisy or squealing sounds coming from the motor during the operation  
• the drum fails to spin or spin inconsistently
• the washer is unable to enter spin cycles
• slow or reduced agitation 

Causes of a bad part include normal wear and tear over extended use. As the brushes continuously contact the commutator, friction can cause them to wear down over time.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Replacement door hinge for front-load washers. Supports door weight and enables smooth opening/closing. Replace if cracked, broken, or causing door sag.

The Washer Filter-Fluff is an OEM replacement part for Bosch washing machines. It is a critical component responsible for capturing lint, debris, and other particles that may accumulate during the wash cycle, preventing them from clogging the drainage system or causing damage to the machine.

Over time, the accumulation of lint and debris can impede the filter's effectiveness, leading to drainage issues and reduced washing performance. Physical damage to the filter can also compromise its ability to capture lint properly.

Symptoms of a bad washer filter-fluff include:

• Slow or incomplete draining of the washing machine
• Excessive lint on clothes after washing
• Unusual noises during the drain cycle
• Error codes related to drainage issues

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore washing machine models. 

Secures the washer door handle to the door assembly. Replace if worn, bent, broken, or missing to restore a firm grip and prevent handle detachment.

Plastic bushing that sits between the washer door hinge and pivot point. Replace when worn, cracked, or causing loose door alignment and noisy operation.

This interference capacitor suppresses electrical noise and radio-frequency interference to help the appliance's electronics run more reliably. It fits on the control board and supports stable operation by filtering stray voltage spikes. What it does:

• Filters electrical and radio-frequency interference that can cause erratic control behavior or false error codes
• Reduces electrical noise that can affect nearby audio or radio reception
• Helps protect control circuitry from transient voltage spikes
• Commonly used when appliance exhibits intermittent faults or unexplained control glitches

• Disconnect power to the appliance before starting any repair
• Discharge capacitors and avoid touching leads; use insulated tools and follow safe-handling practices
• Replace only with the exact part specified for your model and secure all wire connections firmly

Coupling that connects the program knob to the timer mechanism on your washer. Replace if cracked, stripped, broken, or missing for proper cycle selection.

Replace your washer door seal to stop leaks and prevent water damage. Essential for maintaining a tight seal during wash cycles. Verify fit with your model.

Door trim piece that holds and secures the viewing glass in your washer door. Replace a cracked, warped, or missing frame to restore proper fit and appearance.

Fix washer drainage issues with this sump check ball. Prevents water backflow in the pump system. Simple DIY repair for most home mechanics.

This replacement side panel installs on the left or right side of the dishwasher rough-in box to restore a finished appearance and provide proper side coverage during installation. It matches the OEM fit for compatible Bosch rough-in housings. What it does:

• Covers and protects the exposed side of the rough-in box for a finished look
• Helps align and secure the cabinet opening during appliance installation
• Replaces a cracked, dented or missing side panel that exposes wiring or connectors
• Preserves the original fit and appearance of the installation area

• High-level fit: installs to the rough-in box as shown in OEM diagrams; confirm correct side before fastening
• Turn off power to the appliance area before starting work and follow local electrical/safety codes
• Use existing mounting points and hardware where possible; replace damaged fasteners with OEM-equivalent parts

Washer sponge absorbs moisture and prevents leaks. Replace if damaged, compressed, or no longer absorbing water. Confirm fit with your model number.