Gaggenau Dishwasher DF241760 Parts

This replacement screw secures appliance panels and internal brackets so components stay tight and aligned during everyday use. Replacing missing or stripped hardware restores a solid fit and helps minimize vibration and rattling.

• Fastens covers, panels, and brackets to their mounting points
• Helps maintain alignment of the attached component
• Reduces movement that can cause noise or wear
• Typical reasons to replace: missing screw, stripped head/threads, loose panel or bracket

• Disconnect power and, if applicable, shut off water before servicing
• Use the driver bit specified for your model; hand start threads to avoid cross-threading
• Tighten snugly without over-torquing to prevent stripping
• Replace screws one at a time to maintain alignment

Dishwasher indicator light not working or staying on? This light signals cycle status and alerts. Common fix for control panel display issues.

Replacement silverware basket with handle for dishwasher lower rack. Holds utensils upright for better cleaning. Replaces cracked, broken, or missing baskets.

This replacement switch restores reliable electrical control within your appliance. It opens and closes an electrical circuit to signal the control system, so power and functions respond consistently when the switch is actuated.

• Opens/closes an electrical circuit when the actuator is engaged
• Sends an on/off or selection signal to the control or main board
• Helps address: no response or no start, intermittent operation, stuck on/off state, or heat-damaged/burned terminals
• Direct replacement for the original switch on applicable units

• Disconnect power at the breaker and unplug the unit before servicing
• Access the control area to reach the switch; note wire locations or take a photo
• Transfer wires one at a time for correct orientation; ensure snug terminal connections
• Reinstall mounting hardware, reassemble panels, restore power, and test operation

Seals the NTC temperature sensor port in your dishwasher to prevent leaks and ensure accurate temperature readings. Replace if leaking or worn. Verify fit with your model number before ordering.

Circular sealing gasket creating watertight joints between dishwasher components. Replace when flattened or cracked to prevent leaks. Confirm fit by model.

Support strap that cushions and secures the dishwasher circulation motor, stabilizing the motor assembly to reduce vibration and help maintain alignment for steadier, quieter operation. Designed for circulation motors with softer bearings. What it does:

• Cushions and supports the circulation motor to limit movement and vibration and reduce motor noise.
• Secures the motor assembly to the tub/chassis to maintain proper clearance and fit.
• Helps prevent undue stress on motor bearings and mounting points that can cause premature wear.
• Commonly replaced when the strap is cracked, stretched, or no longer holds the motor firmly in place.

• Disconnect power and water supply before servicing; follow all safety and OEM service instructions.
• Remove access panels and any obstructing components to reach the circulation motor as required.
• Replace using the original mounting hardware; inspect motor mounts and bearings while accessible.
• Reassemble and run a short test cycle to confirm reduced vibration/noise and proper motor operation.

Seals the aqua sensor assembly to prevent water leaks and protect electronics. Replace if you notice leaks or sensor errors. Confirm fit with your model.

Dishwasher not draining or water pooling at bottom? A cracked sump disrupts water flow to the pump. This housing restores drainage and prevents leaks.

Left side door hinge for your dishwasher. Replaces damaged, bent, or broken hinges that cause the door to fall open or swing too far. Bushing included.

Right side door hinge plate for dishwashers. Secures the door hinge mechanism to the frame. Replace if cracked, broken, or damaged to restore proper fit.

Left side door hinge plate for your dishwasher. Replaces cracked, broken, or worn hinge plates that cause door misalignment or instability.

Repair set for dishwasher rack rollers. Restores smooth rack movement when wheels are broken, cracked, or worn. Installs on upper or lower racks.

Dishwasher door guard installs on the door hinge for reinforcement and support. Replace if cracked, broken, or missing to prevent door bending.

Metal mounting bracket that secures the toe kick panel to the bottom of your dishwasher. Replace if bent, broken, or missing to properly attach panel.