Gaggenau Dishwasher DF241760 Parts

Hose, with o - ring, shu (uc/12 & above)

This Sump to Float Hose is an OEM part for Bosch Dishwashers. It functions to carry water from the dishwasher sump to the float assembly. Continuous water flow and exposure to detergents can lead to wear or damage over time.

What Causes a Bad Sump to Float Hose:
Exposure to chemicals and hot water, along with wear from water flow, can cause the hose to degrade or develop cracks.

Symptoms of a Bad Sump to Float Hose:

• Water leakage around the dishwasher
• Incomplete or interrupted washing cycles
• Visible cracks or damage to the hose

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Dishwasher won't start or keeps tripping the breaker? A damaged terminal box with melted connections is often the cause. Moderate DIY repair.

The Sealing is an OEM replacement part for Bosch brand dishwashers. Located on the perimeter of the small rinse aid compartment door, this resilient rubber piece forms an essential water-tight seal when the dispenser is closed.   

Symptoms of a potentially problematic rinse aid door sealing include:

• Leakage or spills within the rinse aid reservoir
• Mineral deposits or residue build up inside the compartment  
• Cracks, tears, or deformation of the sealing material

Causes of a faulty rinse aid door sealing can be repetitive opening/closing stress breaking down pliability long-term. Exposure to chemical vapors from the rinse aid may also degrade sealing properties.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

2 clamps included.

Plastic cover that protects the drain pump mechanism from debris. Replace if cracked, broken, or tabs are bent preventing proper seal during drain cycles.

Replace a missing or damaged junction box cover on your dishwasher. Protects power supply and control board wiring connections. Easy DIY repair.

Fix dishwasher not heating or running for hours. This NTC temperature sensor monitors water temp and prevents overheating. Moderate DIY repair with video.

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

Fix a dishwasher that won't fill, overfills, or leaks from the base. Water inlet valve controls flow into the tub. Moderate DIY repair, 30-45 minutes.

O-ring seal prevents leaks between dishwasher components. Replace when you notice water drips or moisture buildup. Confirm fit with your model number.

Secures the dishwasher sump or sump cover to the tub for a tight, leak-resistant seal. Replace if missing, stripped, or damaged to restore stability.

This upper trim strip finishes the top edge of the appliance's front opening, restoring a clean look and helping protect nearby components. Replace a cracked, missing, or loose strip to keep panels aligned and secure.

• Provides a finished edge along the upper portion of the door/face area
• Helps protect adjacent components from dust and minor splashes
• Maintains proper panel gaps and alignment
• Typical symptoms: visible cracks, warping, looseness, rattling, or exposed/sharp edges

• Disconnect power before servicing; also shut off water
• Remove the existing strip by releasing screws/clips; retain hardware for reuse
• Align the new strip and secure evenly—do not overtighten fasteners
• Check door/panel operation afterward to confirm proper fit and clearance

The Float is an OEM part for Bosch dishwashers. This float senses water levels inside the dishwasher, signaling the inlet valve to refill when needed.

Causes of a float malfunctioning can be mineral deposits accumulating and weighing it down over time, or cracks in the plastic housing allowing water in.

Symptoms of a bad float include:

• The dishwasher not filling or filling slowly
• Error codes related to fill issues
• Improper water levels impacting wash results

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

Wax motor for detergent/rinse-aid dispenser.

Detergent not dispensing during wash cycle? This actuator arm with spring releases the detergent cup at the right time. Moderate DIY repair.

This dishwasher door spring counterbalances the door's weight for smooth, controlled opening and closing. Replacing a worn or broken spring restores proper door tension and helps prevent the door from dropping quickly or feeling heavy.

• Provides tension to counterbalance the dishwasher door during opening and closing
• Helps prevent the door from slamming open or feeling overly heavy
• A weakened or broken spring can cause uneven door movement, squeaks, or the door not staying in a partial-open position
• Restores smooth, even door operation when replaced

• Disconnect power and turn off water supply before servicing
• Remove the toe-kick and carefully slide the dishwasher out to access the side/frame area where the spring attaches
• Note the original spring attachment points and orientation; install the new spring in the same locations
• Springs are under tension—use caution and hand protection; many replace both springs together to maintain balanced tension