Kenmore Refrigerator 106.44434603 (10644434603, 106 44434603) Parts

This replacement gasket seals the appliance door to help maintain proper temperature and prevent leaks, keeping the interior efficient and protected. Use it to restore a tight door seal and reduce energy loss from gaps. What it does:

• Forms a secure seal around the door to keep heat or cold inside the appliance
• Prevents water, steam, and air leaks that can cause poor performance or messes
• Helps maintain consistent internal temperature for efficient operation
• Reduces cycling and energy waste caused by a damaged or worn seal

• One replacement gasket

• Disconnect power and empty the appliance before starting any repair
• Inspect the door frame and mounting channel for damage or debris before installing
• Install by seating gasket evenly into the channel or following the OEM mounting clips/adhesive method

This replacement dispenser lever restores proper operation to a refrigerator water dispenser so you can reliably access water without using a damaged or worn lever. Fits the dispenser assembly and provides a stable push surface. What it does

• Replaces a cracked, loose, or broken water dispenser lever so the dispenser paddle responds correctly.
• Helps stop sticking or uneven travel that prevents the valve from activating.
• Restores proper alignment with the dispenser bezel and actuator for consistent operation.
• Suitable when the lever is worn, chipped, or no longer returns smoothly.

• One dispenser lever

• Basic hand tools typically required; avoid forcing plastic tabs to prevent breakage.
• Disconnect power to the appliance and turn off the water supply before replacing parts that interact with the dispenser valve.
• Handle the new lever carefully to avoid damaging mounting clips; test function gently after installation.

This blade mounting block secures the blade assembly to the appliance, keeping cutting or stirring components aligned for reliable operation and reduced vibration. It restores proper blade positioning to help eliminate noise and uneven performance. What it does:

• Supports and locates the blade assembly so blades stay aligned during operation
• Prevents wobbling or contact that can cause noise and premature wear
• Helps restore consistent cutting/stirring action when a loose or damaged block is present
• Common symptom: loose blade, rattling or grinding noises, or uneven operation

• One blade mounting block

• Disconnect power (and water if applicable) before beginning any repair
• Remove blade assembly per OEM instructions to access and replace the block
• Inspect surrounding components (fasteners, blades, seals) for wear and replace as needed

Includes both right and left hand sides.

This insul-sound deadening pad reduces vibration and noise by dampening panels and components in laundry and kitchen appliances. It's a small adhesive-backed sound/isolation pad used where noise or rattles transfer through metal surfaces. What it does

• Dampens rattles and reduces structure-borne noise from panels, cabinets and housings.
• Helps isolate vibrating components from appliance chassis to lower perceived sound.
• Commonly applied behind control panels, cabinet walls or on motor mounts to cut vibration transmission.
• Useful when worn, detached or hardened factory pads allow increased noise.

• One insul-sound deadening pad

• Disconnect power before servicing an appliance to avoid shock or injury.
• Clean and dry mounting surface; press pad firmly to ensure adhesive contact.
• Replace only in the original location; do not cover vents or moving parts.
• If adhesive is weak, use OEM-approved adhesive; avoid solvents that may damage finishes.

The Water Reservoir Tubing is an OEM replacement part for Whirlpool refrigerators. It is a flexible plastic tubing that replaces the water reservoir and holds the water for the ice maker and dispenser.

Causes can include cracks from heat or cold exposure over time, punctures from sharp edges during installation, or deterioration of plastic tubing that impacts integrity.

Symptoms of bad water reservoir tubing include:

• Inaccurate or inconsistent ice production
• Leaks or water spills near the reservoir or ice maker
• Kinks or ruptures in the tubing that obstruct water flow
• Mineral buildup that clogs or restricts the line

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Note: As per manufacture this is no longer a tank. The tank style has been updated with coiled tubing.

This mounting bracket secures internal components and panels so they stay aligned and stable during operation. It replaces a worn or broken bracket to restore proper support and reduce vibration or movement. What it does:

• Provides a secure mounting point for internal parts or panels
• Helps prevent rattling, misalignment, or loose panels during use
• Restores proper fit and stability when an original bracket is cracked or bent
• Works as a direct-replacement hardware piece where specified by the manufacturer

• Disconnect power to the appliance before starting any repair
• Use basic hand tools; keep fasteners and orientation the same as removed
• If the bracket is attached to electrical components, handle wiring carefully and inspect connectors