Kenmore Refrigerator 106.56936600 (10656936600, 106 56936600) Parts

Replace a cracked, broken, or missing freezer bin to restore organized storage in your refrigerator. Direct-fit drawer keeps frozen items contained.

This bearing nut secures a bearing and related rotating components on the shaft, keeping the assembly tight and aligned for smooth, dependable operation. Replacing a worn or stripped nut helps stop wobble, noise, and drive slippage.

• Locks the bearing/stack onto the shaft to prevent loosening
• Maintains alignment for smooth rotation and reduced vibration
• Helps restore consistent drive in shaft-driven assemblies
• Typical symptoms: loose or non-turning drive, rattling/grinding, or visible thread damage

• Disconnect power before servicing; shut off water if working near dispenser components
• Remove the related assembly to access the shaft; note part order for reassembly
• Hand-start the nut to avoid cross-threading; verify thread direction against the original
• Tighten securely; inspect the bearing, washers/spacers, and shaft for wear

Crisper drawer won't adjust humidity or slide is broken? This humidity control slide mounts in the crisper cover to regulate airflow and moisture levels.

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.

Bottom hinge shim for refrigerator doors. Adjusts door height and alignment for proper seal. Replace if door sags or doesn't close evenly. Confirm fit.

Secures cabinet or door handle to your refrigerator. Replace this clip if your handle is loose, sagging, or detached from the door mounting point.

Fix ice not dispensing properly with this ice crusher blade. Replaces free-wheeling or worn blades on the auger assembly. DIY-friendly repair.

This terminal block cover protects the appliance's electrical connection area from accidental contact and debris, helping reduce the risk of shorts and corrosion while keeping wiring secure and contained. What it does:

• Covers and shields the power terminal/block where the power cord connects
• Helps prevent accidental contact with live terminals and reduces short risk
• Keeps out dust, lint and debris that can cause corrosion or arcing
• Useful when the original cover is cracked, missing or showing burn marks

• Always disconnect power (unplug or switch off breaker) before servicing electrical components
• Typically installs over the terminal block and secures with the existing fastener(s); inspect mounting hardware for wear
• Replace if cracked, melted or if terminals are exposed; ensure cover seats fully before restoring power

White plastic hinge cover for refrigerator doors. Replaces cracked, broken, or missing hinge covers. Installs over door hinge mechanism for clean look.

This right-side basket track guides the dishwasher rack for smooth in-and-out movement and keeps the rack aligned during use. Replacing a worn or damaged track restores proper rack travel and prevents catching or tipping. What it does:

• Supports the right side of the lower (or designated) rack so rollers can glide along the cabinet wall
• Prevents the rack from binding, skipping, tipping, or falling off the rail
• Reduces scraping, grinding, or loud noises caused by a broken or warped track
• Helps maintain proper rack alignment for consistent loading and drainage

• Disconnect power (or unplug) and turn off water supply before beginning work
• Remove the affected rack to access and remove the old track and any end clips or stops
• Reinstall the new track, secure any retainers, then replace the rack and test smooth travel
• Use basic hand tools; replace clips or rollers if damaged.

Round cap button that covers the water filter housing on your refrigerator. Replace if cracked, broken, missing, or no longer snaps securely into place.

Fix ice that won't crush or dispense with this refrigerator crusher blade. Solves bent or damaged blades preventing ice from dispensing. Easy DIY repair.

Replace your cracked or cloudy dispenser light lens to restore clear illumination. Protects the bulb and improves visibility. Verify fit with your model.

Ice cubes stuck in tray and won't eject? This ejector arm pushes ice from the mold into the bin. Simple snap-in install restores ice production.

Slide air control that regulates airflow between freezer and fresh food compartments. Replace if cracked, broken, or won't slide smoothly.

Fix loose wiring or rattling sounds in your refrigerator with this terminal block clip kit. Secures harnesses and panels to restore proper fit.