Kenmore Refrigerator 106.58979705 (10658979705, 106 58979705) Parts

This cabinet roller assembly supports the refrigerator at the base and lets you roll the unit forward for cleaning or service. Replace a cracked or seized roller to restore smooth movement and a stable, level stance. What it does:

• Supports the refrigerator cabinet and helps maintain proper leveling
• Allows the unit to roll for easier cleaning and servicing
• Replaces worn, cracked, or seized rollers and damaged brackets
• Helps resolve wobbling, uneven stance, scraping noises, or difficulty moving the fridge

• One complete cabinet roller assembly

• Disconnect power and turn off the water supply before servicing
• Protect flooring and use a second person or an appliance dolly to safely tilt or move the unit
• Remove mounting fasteners, swap the assembly in the original position, and reuse hardware if applicable
• After installation, level the refrigerator and verify doors close and seal properly

The Handle Set Screw is an OEM part for Whirlpool refrigerators. As an internal component, the set screw is used to securely hold refrigerator door handles in place for easy opening and closing of access doors. 

Symptoms of a bad handle set screw include: 

• Handles that spin loose and no longer open doors properly
• Loss of attachment causing handles to fall off doors    
• Potential for handles to fall on feet presenting a safety hazard
• Opening issues, like hands slipping off spinning handles 

Causes involve wear from repeated use or accidental tightening damage stripping threads and allowing handle loosening, affecting usability.

This OEM Whirlpool part is also compatible with some Kenmore and KitchenAid models.

The Shelf Stud is an OEM part for Whirlpool refrigerators. It serves as a support peg that holds the refrigerator shelves in place, ensuring they remain stable and properly positioned.

Causes of a bad shelf stud can include wear and tear from regular use, accidental impact that causes the stud to break, or repeated removal and reinstallation of shelves leading to loosening or damage.

Symptoms of a bad shelf stud include:

• Shelves not staying securely in place
• Shelves tilting or collapsing
• Visible cracks or damage to the stud
• Difficulty in inserting or removing shelves

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is a rear stud with a screw. For the front stud with screw use part number W11223328. For studs with no screw use kit part number 4388538.

Clip for bottom grill. If your original clip is riveted, order screw WP489478.

This lower ice crusher bin fits inside the ice bucket and holds the crusher blade stack in position as cubes are processed. Replacing a cracked or worn bin restores reliable crushed-ice dispensing and helps prevent jams and grinding noises.

• Supports and aligns the crusher blades inside the ice bucket during dispensing
• Helps produce crushed ice when selected at the dispenser
• Maintains proper clearances to reduce jams and inconsistent ice size
• Symptoms: ice won't crush, only cubes dispense, dispenser jams or makes grinding noises, visible cracks in the crusher bin

• Disconnect power and remove the ice bucket from the freezer.
• Carefully disassemble the crusher assembly, noting the order and orientation of blades and spacers.
• Transfer components to the new lower bin and ensure tabs/retainers are fully seated.
• Reinstall the bucket and test both Cube and Crush settings.

This push-button door switch senses when your refrigerator door opens and closes to control the interior light. Replace a worn or stuck switch to restore reliable lighting and proper on/off operation when the door moves. What it does:

• Turns the interior light on when the door opens and off when it closes
• Common fix for a light that won't turn on with the door open
• Resolves lights that stay on continuously with the door closed
• Addresses intermittent lighting from a sticking or damaged plunger

• One door switch

• Disconnect power to the refrigerator before servicing
• Carefully pry the old switch from the liner; protect the surface to avoid damage
• Transfer wires to the new switch one at a time to maintain correct connections
• Press the new switch fully into place and restore power to test operation

This flexible, narrow brush reaches under and behind the cabinet to sweep dust and lint from condenser coils and vents. Cleaning built-up debris helps restore airflow and support proper cooling performance.

• Sweeps dust, lint, and pet hair from condenser coils and ventilation areas
• Flexible reach helps access coils beneath or behind the appliance
• Aids proper heat dissipation by clearing airflow paths
• Helpful when coils are visibly dirty, cooling seems weak, or the unit runs longer than usual

• Unplug or disconnect power before cleaning
• Remove the toe grille or rear access panel if needed to access coils
• Brush gently along the coil fins; avoid bending fins or damaging tubing
• Vacuum or wipe up loosened debris before replacing any panels and restoring power

Color: Black

Color: Black

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This replacement ice maker cover snaps over the icemaker assembly to shield moving parts and keep frost and debris out. Replacing a cracked or missing cover helps restore reliable ice production and a clean, finished look inside the freezer.

• Protects the ice maker's internal components from accidental contact and debris
• Helps reduce frost buildup around the ejector and motor area
• Maintains proper fit and clearance for smooth ice harvesting
• Common symptoms: cover cracked, broken tabs, loose or missing cover, excess frost around the icemaker

• Disconnect power to the refrigerator and turn off the water supply
• Remove the ice bin to access the ice maker
• Release any retaining tabs or screws and remove the old cover
• Install the new cover, ensuring the ejector and shutoff arm move freely; restore power and water

Color: clear. It measures about 6 inches wide by 3-1/2 inches high by 15 inches deep.

This replacement ice auger fits inside the freezer ice bin and rotates to move ice to the dispenser and through the crusher, restoring consistent cubed or crushed ice dispensing when the original auger is bent, stripped, or broken.

• Moves ice through the bin to the dispenser chute
• Works with the crusher blades/selector for crushed or cubed dispensing
• Common symptoms: no ice dispensed, motor runs but ice doesn't move, slow or jammed dispensing, grinding noises from the bin
• Replaces a bent, worn, or broken auger spiral that fails to engage or feed ice

• Disconnect power; remove the ice bin from the freezer/door
• Empty the bin; carefully disassemble the crusher blade stack, noting the exact order of blades, spacers, and washers (take reference photos)
• Transfer components onto the new auger and secure the retaining hardware; verify smooth rotation before reinstalling
• Wear cut-resistant gloves—crusher blades and edges are sharp

This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.

• Fastens brackets, panels, trim, or components to the appliance chassis
• Helps correct loose or missing hardware after vibration or service
• Replaces stripped, rusted, or broken screws
• Can reduce rattling noises or misaligned parts caused by missing fasteners

• Disconnect power; for gas appliances, also shut off the gas supply
• Support the part being fastened; start threads by hand to avoid cross-threading
• Use the correct driver size; tighten snugly without overtightening
• Replace hardware with the exact part number to ensure proper fit

Used to prevent water from overflowing from the dispenser on the freezer door. Color: Biscuit. It measures about 10 inches wide by 3 inches deep. For black order WP2206670B. For white order WP2206670W.