Kenmore Refrigerator 106.59966804 (10659966804, 106 59966804) Parts

This support mounts in the dispenser area to secure the ice housing assembly. It helps keep the chute and door properly aligned so ice dispenses smoothly and the opening seals as designed.

• Supports and positions the ice housing/chute assembly in the freezer door
• Helps maintain proper alignment and sealing of the ice door/flapper
• Reduces wobble or flex that can affect dispensing performance
• Typical signs it may be needed: loose or misaligned dispenser housing, ice or air leaking at the chute, frost buildup around the dispenser, inconsistent ice dispensing

• Disconnect power to the refrigerator before servicing
• Remove the dispenser trim/control to access the housing; handle wiring and tabs carefully
• Remove mounting fasteners, replace the support, and transfer any reusable hardware
• Reassemble, restore power, and test ice dispensing and chute seal

Color: Black

This replacement screw secures appliance panels, brackets, and components to the cabinet or chassis. The #8-15 x 1/2 in. size restores a snug, reliable hold when original hardware is missing, stripped, or corroded.

• Fastens panels, brackets, and trim to the appliance cabinet or chassis
• Helps reduce rattling, vibration, or looseness caused by missing/stripped hardware
• Restores proper alignment of parts that have shifted due to loose fasteners
• Size/spec: #8-15 thread, 1/2-inch length; use where this size is specified

• Disconnect power and shut off gas/water supplies before servicing
• Replace one screw at a time to maintain alignment of parts
• Start threads by hand to prevent cross-threading; do not overtighten
• Use a matching driver/bit type for the screw head used in your appliance

This replacement mounting screw secures appliance panels and components to restore proper fit and reduce rattling. Use when a damaged or missing screw causes loose trim, gaps, or vibrating noises; order by part number to ensure a match. What it does:

• Fastens panels, brackets, or trim to keep parts aligned and secure.
• Stops vibration and rattling caused by loose or missing screws.
• Common symptoms: visible gaps, loose panels, hardware falling out, or excess noise.
• Use the part number and/or existing screw to ensure correct size and thread before ordering.

• Disconnect power and water before accessing internal components.
• Use the correct screwdriver or bit to avoid stripping the head.
• Turn until snug; avoid over-tightening which can strip threads or crack trim.
• Keep small parts away from children and pets during repair.

This replacement washer is a small hardware spacer used in appliance assemblies. It provides a smooth bearing surface under a bolt or nut to distribute load and maintain proper spacing so components stay secure, aligned, and quiet.

• Distributes clamp load to protect mating parts and prevent loosening
• Maintains proper spacing/clearance for correct alignment
• Helps reduce wobble, scraping, or vibration when the original washer is worn or missing
• Visual signs include distortion, cracks, corrosion, or a fastener that no longer tightens securely

• Disconnect power before servicing; for laundry or dishwashing products, also shut off the water supply
• Note the original hardware stack-up and orientation; install the new washer in the same position
• Inspect the bolt/nut and mating surfaces; replace any damaged hardware and tighten per manufacturer guidance
• After reassembly, run a brief test and check for unusual noise or movement

Screw: 8-16 x 3/8 inch.

This replacement wiper is the OEM-style rubber blade that clears residue from a sealing surface to help restore proper closure and reduce moisture buildup. Install to replace torn, cracked, or worn wiper material for better sealing performance. What it does:

• Wipes water and debris from the seal or track to help maintain a tight closure.
• Reduces leaks, moisture accumulation, and related odors or frost build-up.
• Stops rubbing or improper closing caused by a damaged or missing wiper.
• Restores the intended contact between the seal and mating surface for reliable performance.

• Disconnect power and follow the appliance manufacturer's safety instructions before servicing.
• Typically installs by sliding or snapping into the wiper channel; use care to avoid stretching or tearing the rubber.
• Clean the mating surface and inspect the retainer or track for damage before installing; replace any damaged retainers per OEM instructions.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This replacement blade is the rotating element used within the appliance assembly to deliver the intended action. Installing a new blade restores smooth, efficient operation when the original is cracked, bent, worn, or missing.

• Provides the mechanical action required by the assembly (rotation/agitation)
• Helps maintain consistent performance and smooth operation
• Common failure signs: rattling or scraping noises, vibration/wobble
• Other symptoms: reduced performance in that section of the appliance, visible chips, cracks, or deformation

• Disconnect power before servicing; turn off water supply if applicable
• Wear cut-resistant gloves; edges may be sharp
• Note the original blade's orientation and spacing before removal; install the new blade the same way
• Hand-rotate after installation to ensure free movement and clearance before restoring power

This flipper spring returns the refrigerator's ice dispenser door (chute flapper) to the closed position after dispensing. It helps keep warm air and moisture out to minimize frost at the chute and reduce ice clumping in the bin.

• Provides the closing tension for the ice chute door/flapper
• Helps maintain a proper seal at the dispenser opening
• If worn or broken, you may notice the flapper not closing fully
• Frost/condensation around the chute or ice clumping in the bucket may occur

• Disconnect power to the refrigerator before servicing
• Remove dispenser trim/control to access the ice chute door assembly; note spring orientation and anchor points
• Install the new spring in the same orientation; the flapper moves freely and closes under spring tension
• Wear gloves and use caution—metal edges in the dispenser area can be sharp

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

This glass refrigerator shelf provides a stable, easy-to-clean surface for storing food and containers inside the fresh-food compartment. It restores proper shelving layout and helps keep items organized and visible. What it does:

• Replaces a broken, cracked or missing glass shelf so food and containers sit level and secure
• Helps contain spills on a wipe-clean surface to simplify cleanup
• Restores usable storage space and original shelf configuration
• Fits into existing shelf supports and works with standard refrigerator shelf clips or rails

• One glass shelf

• Slide shelf into existing support rails or clips; no special tools typically required
• Handle with care — glass edges can be sharp; wear gloves during installation
• Verify shelf is fully seated and level before loading with heavy items
• If shelf clips or rails are damaged, replace them to ensure secure fit

This stripper arm for an ice maker lifts and clears ice from the mold so individual cubes separate and move into the dispenser or storage bin. Replacing a worn or damaged arm restores reliable harvest and ice release. What it does:

• Lifts or sweeps ice out of the ice mold during the harvest cycle
• Helps separate stuck or partially formed cubes so they fall into the bin
• Reduces ice buildup that can cause clumping or delivery problems
• Works as part of the ice maker's ejector/harvest mechanism

• Disconnect power to the appliance before starting any repair
• Confirm position and orientation against the removed part before installing
• May require basic hand tools; handle plastic parts carefully to avoid breakage

This wire harness assembly connects key electrical components to restore proper power and signal flow in the appliance. Replacing a faulty harness helps stop intermittent operation and restores reliable control function. What it does:

• Provides the factory routing and connections between controls, switches, and motors.
• Re-establishes power and signal paths to prevent intermittent or no-power symptoms.
• Stops failures caused by broken, burnt, or loose wires and terminals.
• Ensures secure plug-to-plug connections using original-style terminals.

• Disconnect the appliance from power (and water if applicable) before starting.
• Inspect connectors and routing; replace only if matching the original harness.
• Reuse any mounting clips or grommets; secure wires away from heat and moving parts.

Fresh freezer cabinet top hinge.

This replacement screw fastens panels, brackets, and internal components so they stay secure during operation. Replace worn, rusted, or missing screws to restore a solid fit and help reduce vibration, rattles, and misalignment.

• Secures appliance parts to maintain proper fit and alignment
• Helps reduce noise and vibration from loose panels or trim
• Replaces stripped, corroded, or missing fasteners
• Can resolve issues like rattling, gaps, or shifting components

• Disconnect power; turn off gas/water if applicable before servicing
• Match to the original screw and start threads by hand to avoid cross-threading
• Use the correct driver and tighten snugly; do not overtighten into plastic or thin sheet metal
• Replace additional worn fasteners in the same location if needed for even clamping