Kenmore Refrigerator 106.63142303 (10663142303, 106 63142303) Parts

This air tower is the vertical duct that channels cold air from the evaporator through the cabinet vents to distribute cooling across shelves. Replacing a cracked or blocked tower restores proper airflow and more consistent temperatures.

• Directs and distributes cold air from the evaporator to the fresh food area
• Helps maintain even temperatures and airflow across the compartment
• Common symptoms of failure: weak/no airflow from vents, warm spots, frost/ice around vent area
• Physical damage such as cracks, broken tabs, or warping can allow leaks and reduce cooling

• Disconnect power before servicing; wear cut-resistant gloves
• Remove shelves/drawers and the rear interior panel to access the tower
• Transfer and reuse existing screws/clips; align tower to seal against vent openings
• After installation, restore power and verify unobstructed airflow from vents

Size: 8 x 1/2 ab.

This replacement screw secures appliance components such as panels, brackets, and trim. Replacing a missing, stripped, or corroded fastener restores a snug, rattle-free fit and helps keep parts properly aligned during operation. What it does:

• Fastens panels, brackets, trim, and assemblies in place
• Maintains alignment and reduces vibration or rattling
• Replaces worn, corroded, or missing hardware to ensure safe attachment
• Typical symptoms: loose panel, rattling noises, misalignment, stripped head/threads

• 1 screw

• Disconnect power; shut off gas/water if applicable before servicing
• Match the replacement to the original screw (thread and length) for proper fit
• Start threads by hand to avoid cross-threading; use the correct driver
• Do not overtighten, especially into plastic or thin sheet metal

This crisper cover support mounts to the refrigerator liner and holds the crisper cover frame/glass level. Replacing a broken or missing support restores a stable shelf surface and helps the crisper drawers slide and close properly.

• Supports the crisper cover frame/glass along the cabinet wall
• Maintains a level surface to help prevent sagging or glass shifting
• Keeps crisper drawers aligned and moving smoothly
• Common symptoms: cracked or missing support, shelf tilts, glass slips, drawers scrape or won't close fully

• Disconnect power and clear the shelf area
• Remove crisper drawers and lift out the cover/glass
• Release and remove the damaged support; snap or screw the new support into the same position
• Reinstall the cover and drawers; verify level fit

This lower door hinge supports the refrigerator door at the bottom pivot so it opens smoothly and stays properly aligned. Replacing a worn hinge can restore reliable door closure and help maintain an effective gasket seal.

• Provides the bottom pivot point and supports the door's weight
• Helps keep the door aligned for proper gasket contact
• Allows smooth opening and closing without binding
• Common symptoms of a failing hinge: door sagging, rubbing/scraping, squeaking, or not closing fully

• Disconnect power and, if applicable, shut off the water supply; remove items from the door.
• Support the door, remove the top hinge hardware, and lift the door off the bottom hinge.
• Remove the old bottom hinge from the cabinet/frame and install the new hinge in the same orientation, reusing original screws/shims.
• Reinstall the door and top hinge, then check alignment and gasket seal before restoring power.

Color: clear. It measures about 12 inches wide by 6-1/2 inches high.

This defrost timer cam replaces the plastic cam on a mechanical defrost timer. It restores the timer's changeover between cooling and defrost, helping prevent frost buildup on the evaporator and temperature swings inside the refrigerator.

• Mounts on the timer shaft to actuate the internal switch between cooling and defrost
• Helps resolve issues like heavy frost on the evaporator, warm fresh food section, or a unit stuck in defrost/run
• Corrects timer advancement problems caused by a stripped, cracked, or missing cam
• Typically installed with the defrost timer in the control housing or rear service area

• Disconnect power before servicing
• Access the defrost timer and note the original cam's orientation for reference
• Remove any retainer, pull the old cam straight off, and press the new cam fully onto the shaft without forcing
• Reassemble, then manually advance the timer to confirm it switches modes before restoring power

This top door hinge is the butt hinge assembly that mounts to the cabinet at the top of the refrigerator door, supporting the door and allowing smooth swing. Replacing a worn hinge restores alignment and a reliable seal.

• Provides the upper pivot point for the door
• Keeps the door aligned so the gasket seals correctly
• Wear or damage can cause sagging, rubbing, squeaks, or a door that won't close fully
• Helps reduce air leaks and temperature swings near the door

• Disconnect power and remove items from the door to reduce weight
• Support the door from below; remove the hinge cover and mounting screws
• Note the position of any shims/spacers and transfer them to the new hinge
• Reinstall, align the door, tighten screws, and ensure proper gasket contact

This compressor overload is a thermal protector that opens the circuit if the compressor overheats or draws excessive current. Replacing a failed overload restores reliable starts and helps prevent compressor damage when your refrigerator won't cool.

• Protects the compressor by interrupting power during overheat/overcurrent conditions
• Common symptoms: refrigerator not cooling, compressor won't start, repeated clicking or brief hum then shutoff
• Mounts on the compressor terminal and works alongside the start relay on applicable models
• Built for proper fit and dependable operation in the start circuit

• Unplug the refrigerator and remove the rear access panel to reach the compressor
• Note wire positions; pull the old overload straight off the compressor pin
• Push the new overload fully onto the correct terminal and reconnect wiring/terminal cover
• Restore power and verify the compressor starts without repeated clicking

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This start relay mounts on the side of the refrigerator's compressor and momentarily powers the start winding so the compressor can start reliably—helping restore consistent cooling and eliminating repeated click-and-no-start issues.

• Provides the initial boost to start the compressor, then disengages automatically
• Supports proper refrigerator and freezer temperatures by ensuring reliable compressor starts
• Common symptoms of a failing relay: warm temps, compressor won't start, rapid clicking or humming from the rear, or repeated overload trips
• Intermittent cooling after power cycling can also point to a weak start relay

• Unplug the refrigerator before servicing; pull the unit forward to access the rear
• The start device is under a small cover on the compressor side; remove the cover to access
• If a run capacitor is present, discharge it before handling any wiring
• Note wire positions and relay orientation; push the new relay straight onto the compressor pins without bending terminals, reinstall the cover, and restore power

This rubber grommet cushions and secures a refrigerator fan motor, isolating vibration to help reduce noise and keep the fan properly aligned in its mount.

• Provides a snug, vibration-dampening seat for the fan motor shaft or mounting stud
• Helps prevent rattling, buzzing, or humming sounds from a loose fan mount
• Maintains proper fan alignment to avoid blade contact with shrouds or brackets
• Replaces aged, cracked, or compressed rubber that can lead to increased vibration

• Disconnect power before service; wear cut-resistant gloves
• Access the fan assembly (rear or evaporator section), support the motor, and remove the old grommet
• Press the new grommet fully into the bracket or housing; transfer any spacers as originally configured
• Reinstall the motor and verify the fan blade spins freely with no contact before restoring power

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement light bulb restores clear, reliable illumination so you can see contents and monitor appliance operation. Replace a burned-out, dim, or flickering bulb to bring visibility back to the area it lights. What it does:

• Provides illumination in the appliance's interior or designated lighting location
• Makes it easier to see contents and check status at a glance
• Common symptoms: light won't turn on, intermittent/flickering light, dim or blackened bulb

• 1 light bulb

• Disconnect power before servicing; allow hot surfaces and the old bulb to cool completely
• Remove any lens/cover, then remove the old bulb
• Install the new bulb securely without overtightening; reinstall the lens/cover if present
• Restore power and test operation

This thimble is a small insert used in the freezer compartment. It reinforces a mounting hole, prevents liner wear, and helps keep attached hardware stable and properly aligned for smooth, quiet operation.

• Serves as a protective bushing for a hole in the freezer compartment liner
• Helps stabilize and align the component secured at that location
• Replaces cracked, worn, or missing inserts that can cause loose hardware, wobbling, or rattling
• Restores proper fit while helping prevent further wear to the liner

• Unplug the refrigerator and clear the work area in the freezer before service
• Remove the fastener/component to access the insert, then pull the old thimble straight out
• Press the new thimble fully into the hole; reinstall hardware without overtightening
• Use care—cold plastic and liner edges can be brittle or sharp

This replacement handle fits the fresh food door on select refrigerators. It restores a solid, comfortable grip and a clean factory look when the original handle is cracked, loose, discolored, or missing.

• Attaches to the refrigerator door to provide a sturdy handhold for opening and closing
• Replaces worn, broken, or scuffed handles and improves appearance
• Helps resolve issues like a wobbly or stripped-hardware handle
• White finish matches the original color on compatible models

• Note RC orientation and compare to your original before installing
• Protect the door finish with masking tape; align the handle before tightening
• Start fasteners by hand to avoid cross-threading; tighten evenly and do not overtighten
• If your model uses hidden set screws or trim caps, install them after aligning the handle