Kenmore Refrigerator 106.74984401 (10674984401, 106 74984401) Parts

This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.

• Fastens panels, brackets, covers, or internal parts to the chassis or frame
• Helps maintain alignment and support, reducing rattle, vibration, or looseness
• Replaces missing or damaged screws that have backed out, broken, or stripped
• Restores secure mounting after service when original hardware is lost

• Disconnect power; shut off water or gas supplies before servicing
• Use the correct driver; start threads by hand to avoid cross-threading
• Match length and thread to the original location; do not substitute with longer hardware
• Tighten snugly; do not overtighten into plastic or thin metal

Vertical duct that channels cold air from the evaporator through cabinet vents. Replace if cracked, broken, or blocked to restore proper airflow distribution.

Magnetic door gasket creates an airtight seal to keep cold air in. Replace if worn, cracked, or not sealing properly to maintain temperature and efficiency.

Metal support bar that mounts to the refrigerator liner to hold the crisper cover frame and glass level. Replace if broken, missing, or bent.

This ice maker shut-off arm is the wire lever that detects the ice bin level and stops production when raised. Replace a bent, broken, or missing arm to restore reliable on/off control of your icemaker.

• Monitors bin fullness; in the up position it opens the internal switch to pause ice making
• Lowers as ice is used so the icemaker can resume cycles
• Restores manual shutoff when you lift the arm

• Disconnect refrigerator power and turn off the water supply before servicing
• Remove the ice bin for access; open the icemaker front cover if your model has one
• Pull the old arm straight out of the pivot holes; align and fully seat the new arm so it moves freely
• Restore power and lower the arm to resume ice production; the arm raises and stops production when the bin is full

Supports the refrigerator door at the bottom pivot point. Replace if your hinge is rusted, bent, cracked, or broken to restore proper door alignment.

Freezer Door Gasket

Crisper drawer won't adjust humidity? This slide moves the vent door to regulate moisture in your produce bin. Snap-in replacement restores humidity control.

The Screw is an OEM part for Whirlpool refrigerators. This screw secures the refrigerator door hinge in place, allowing the door operates smoothly and seals properly. 

Over time, screws can become loose or go missing during repairs or adjustments, which can lead to a misaligned door, compromised sealing, and increased energy consumption. 

Symptoms of a bad screw include:

• The refrigerator door seems misaligned or does not close properly.
• Increased effort needed to open or close the door.
• Unusual gaps around the door seal when closed.
• The door might squeak or make other noises during operation.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Stops refrigerator fan rattling and buzzing noise. This rubber grommet cushions the fan motor to reduce vibration. Simple DIY fix, takes under 30 minutes.

White plastic cap that secures the water filter in place. Replace if cracked, broken, or missing to properly hold your refrigerator's filter cartridge.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

Replaces the upper butt hinge assembly that mounts to the cabinet and supports your freezer or refrigerator door. Needed when hinge is cracked or worn.

This is a small white plastic plug that fills the hinge sleeve hole on a refrigerator or freezer door. It covers unused hinge mounting holes to provide a clean, finished appearance, especially after reversing the door swing. Replace this plug if it has cracked, fallen out, or gone missing, leaving an exposed hole in the door.

This is the frame that covers the top of the crisper drawers in a refrigerator, serving as a support shelf and helping to separate the crisper compartment from the rest of the fresh food section. It maintains proper airflow and humidity levels around the crisper drawers for better produce storage. Replace this cover frame if it is cracked, broken, or warped, which can cause items to fall through or reduce the effectiveness of the crisper drawers.

Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.