Kenmore Refrigerator 106.77229700 (10677229700, 106 77229700) Parts

This humidity control body mounts on the crisper cover and forms the adjustable vent for the produce drawer. Replacing a cracked or missing housing restores smooth slider operation and helps manage moisture inside the crisper.

• Houses the humidity control slider and covers the vent opening on the crisper cover
• Regulates airflow into the drawer to help manage moisture for fruits and vegetables
• Restores proper fit when the original part is cracked, warped, or missing
• Common symptoms: loose or stuck slider, difficulty adjusting crisper humidity, excess condensation or wilting in the drawer

• Disconnect power; remove the crisper drawer and cover, handling any glass carefully
• Release retaining tabs or screws and remove the old humidity control body
• Transfer the existing slider/indicator as needed and seat the new body fully
• Verify smooth slider movement before reinstalling the cover and drawer

This lower door hinge supports the refrigerator door at the bottom pivot so it opens smoothly and stays properly aligned. Replacing a worn hinge can restore reliable door closure and help maintain an effective gasket seal.

• Provides the bottom pivot point and supports the door's weight
• Helps keep the door aligned for proper gasket contact
• Allows smooth opening and closing without binding
• Common symptoms of a failing hinge: door sagging, rubbing/scraping, squeaking, or not closing fully

• Disconnect power and, if applicable, shut off the water supply; remove items from the door.
• Support the door, remove the top hinge hardware, and lift the door off the bottom hinge.
• Remove the old bottom hinge from the cabinet/frame and install the new hinge in the same orientation, reusing original screws/shims.
• Reinstall the door and top hinge, then check alignment and gasket seal before restoring power.

White. For black order WP2186494B. For biscuit order WP2186494T.

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

Compressor relay and overload.

This glass shelf replaces a cracked, missing, or unstable shelf in your refrigerator, restoring a sturdy, level surface for food storage. Swap in this panel to improve safety, contain small spills, and reclaim usable space.

• Provides a flat, stable storage surface inside the compartment
• Helps contain minor spills within the shelf area
• Seats into the existing shelf frame or support rails
• Common symptoms: cracked, chipped, or missing glass; shelf won't sit level; reduced storage space

• Remove food from the shelf area and carefully lift out the damaged glass.
• Clean the frame/rails and inspect supports before installing the new panel.
• Handle glass with care; wear cut-resistant gloves and eye protection.
• Set the new glass fully into the frame or rails before loading items.

This top door hinge is the butt hinge assembly that mounts to the cabinet at the top of the refrigerator door, supporting the door and allowing smooth swing. Replacing a worn hinge restores alignment and a reliable seal.

• Provides the upper pivot point for the door
• Keeps the door aligned so the gasket seals correctly
• Wear or damage can cause sagging, rubbing, squeaks, or a door that won't close fully
• Helps reduce air leaks and temperature swings near the door

• Disconnect power and remove items from the door to reduce weight
• Support the door from below; remove the hinge cover and mounting screws
• Note the position of any shims/spacers and transfer them to the new hinge
• Reinstall, align the door, tighten screws, and ensure proper gasket contact

This is a refrigerator control board that can be used to replace a damaged or faulty board in select refrigerators. The control board is used to manage various functions that occur in the refrigerator, including cooling and defrosting. If there is a problem with the board, the refrigerator might not be able to defrost correctly, or it might not stay cool.The control board for the refrigerator tends to last a long time. However, it could eventually wear out and stop working. It could be damaged due to a voltage surge, or it might be a faulty board. Remove and store all food in the refrigerator and unplug it before beginning repairs.This refrigerator control board works with certain models from Kenmore, Whirlpool, KitchenAid, Roper, Estate, Inglis, Crosley, Gladiator, Kirkland, and Maytag. It's sold individually and is a genuine OEM replacement.

This rubber grommet cushions and secures a refrigerator fan motor, isolating vibration to help reduce noise and keep the fan properly aligned in its mount.

• Provides a snug, vibration-dampening seat for the fan motor shaft or mounting stud
• Helps prevent rattling, buzzing, or humming sounds from a loose fan mount
• Maintains proper fan alignment to avoid blade contact with shrouds or brackets
• Replaces aged, cracked, or compressed rubber that can lead to increased vibration

• Disconnect power before service; wear cut-resistant gloves
• Access the fan assembly (rear or evaporator section), support the motor, and remove the old grommet
• Press the new grommet fully into the bracket or housing; transfer any spacers as originally configured
• Reinstall the motor and verify the fan blade spins freely with no contact before restoring power

The Hinge-Sleeve Hole Plug is an OEM part for Whirlpool refrigerators. It is designed to cover the hinge sleeve holes on the refrigerator door, providing a finished look and protecting the internal components from dust and debris.

Common causes of a bad hinge-sleeve hole plug include physical damage during routine maintenance or accidental impacts. A missing or damaged plug can lead to exposure of internal hinge components, potentially causing further damage over time.

Symptoms of a bad hinge-sleeve hole plug include:

• Visible gaps or holes in the refrigerator door hinge area
• Accumulation of dust or debris in the hinge mechanism
• Loose or unstable refrigerator door hinges

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This door handle thimble is a small spacer/bushing used on select refrigerator and freezer doors. It sets the correct stand-off for the handle hardware so the handle mounts securely, aligns properly, and feels solid in use.

• Spaces and aligns the door handle to the correct distance from the door
• Supports the handle mounting stud/screw for a secure fit
• Helps reduce handle wobble, gaps, or scuffing against the door
• Replace if the handle won't tighten evenly or the original thimble is cracked, worn, or missing

• Disconnect power before servicing the appliance
• Support the handle to protect the door finish during removal
• Loosen the handle's set screw(s) or mounting bolt, remove the old thimble, and clean the area
• Seat the new thimble fully, reinstall hardware, and tighten evenly—do not overtighten

This evaporator drip pan—also called the drain pan or evaporating tray—collects defrost water from the freezer and allows it to evaporate safely. Replacing a cracked or warped pan helps stop puddles and odors under your refrigerator.

• Collects defrost meltwater and allows it to evaporate using condenser heat/airflow
• Helps prevent water from reaching the floor
• Common symptoms of a bad pan: puddles under or behind the refrigerator, musty odor, visible cracks/warping, or a loose fit
• Restores proper moisture management in the machine compartment

• Unplug the refrigerator and pull it forward to access the rear service area; wear gloves to protect from sharp edges
• Remove the lower back panel; the pan sits near the compressor—slide the old pan out
• Reuse original supports/hardware; ensure the defrost drain tube empties into the new pan and the pan sits level
• Reinstall the panel, restore power, and check for leaks after a defrost cycle

These inserts are for 1/4 inch plastic tubing. Package of 4.

This replacement handle fits the fresh food door on select refrigerators. It restores a solid, comfortable grip and a clean factory look when the original handle is cracked, loose, discolored, or missing.

• Attaches to the refrigerator door to provide a sturdy handhold for opening and closing
• Replaces worn, broken, or scuffed handles and improves appearance
• Helps resolve issues like a wobbly or stripped-hardware handle
• White finish matches the original color on compatible models

• Note RC orientation and compare to your original before installing
• Protect the door finish with masking tape; align the handle before tightening
• Start fasteners by hand to avoid cross-threading; tighten evenly and do not overtighten
• If your model uses hidden set screws or trim caps, install them after aligning the handle

Bottle with brush. Color: Biscuit paint. It's point-six fluid ounces.