Kenmore Refrigerator 106.9547651 (1069547651, 106 9547651) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2149540
Refrigerator shelf support stud.
Do-It-Yourself Stories from Customers like You
Crisper drawer supports broken Donna D. • Tamarac , FL • October 08, 2014
My Whirlpool fridge is 12 yrs old. The crisper drawer supports finally gave up. I googled the make and model number for repair parts and AppliancePartsPros.com came up. I was actually surprised that I found the support peg and stud. I watched the video on their site on how to replace them, saw that it was easy and ordered the parts that afternoon. To my utter amazement the parts came via FedEx the following afternoon! I have to admit if I didn't watch the video I wouldn't have known how...
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: 4388932
Adaptive Defrost Control Board
Do-It-Yourself Stories from Customers like You
The whirlpool side by side needed upgrade of control components William M. • Sunnyside , WA • February 06, 2017
The 20 year old unit still serves us well, looks good and has been kept in good repair. The condenser fan had stopped so I removed, cleaned and oiled that motor. The decision was made to make an upgrade to the evaporator motor and control units so that the appliance could reasonably be expected to have extended service life. The Ice maker module had been replaced 7 years ago. I ordered the parts and have made the upgrade for temperature controller and the defrost control. If you are in a...
Read more
More
$166.67
- Compare At:
-
$229.92
- You Save:
-
$63.25
Genuine Whirlpool part
By: Whirlpool
Part Number: W10852691
This baffle sits in the ice bin and supports the auger so ice feeds smoothly to the dispenser. Replace a cracked or worn baffle to restore reliable dispensing and reduce jams or grinding from the ice bucket.
- Supports and aligns the ice auger inside the bin
- Guides cubes/crushed ice toward the crusher/dispenser
- Helps prevent auger wobble, binding, or excessive noise
- Failure can show as weak/no ice dispensing or intermittent jams
What's included: 1 baffle Install notes:
- Disconnect power; remove the ice bin from the freezer/door
- Empty the bin and remove any screws/clips securing the baffle
- Transfer any reusable hardware; orient the baffle correctly around the auger
- Tighten fasteners without overtightening; reinstall bin and test dispense
Do-It-Yourself Stories from Customers like You
The ice crusher mechanism on my ice maker wasn't working properly i was getting bits of white plastic in my ice so obviously something was broken in there Tawna M. • Orem , UT • July 27, 2015
I found a video/tutorial on how to take it apart to see what was pieces were broken, then ordered the replacement parts and watched the video to put it back together again.
Read more
More
$25.95
- Compare At:
-
$30.62
- You Save:
-
$4.67
Genuine Whirlpool part
By: Whirlpool
Part Number: W11233072
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
- Fastens panels, brackets, covers, or internal parts to the chassis or frame
- Helps maintain alignment and support, reducing rattle, vibration, or looseness
- Replaces missing or damaged screws that have backed out, broken, or stripped
- Restores secure mounting after service when original hardware is lost
What's included: 1 screw Install notes:
- Disconnect power; shut off water or gas supplies before servicing
- Use the correct driver; start threads by hand to avoid cross-threading
- Match length and thread to the original location; do not substitute with longer hardware
- Tighten snugly; do not overtighten into plastic or thin metal
Do-It-Yourself Stories from Customers like You
Bake element broken on jenn air model s125 downdraft slide in range Patricia D. • Raleigh , NC • May 02, 2015
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process.
To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -...
Read more
More
$20.95
- Compare At:
-
$24.93
- You Save:
-
$3.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489478
Size: 8 x 1/2 ab.
Do-It-Yourself Stories from Customers like You
Wanted to update wood paneled compactor Julie S. • San Antonio , TX • December 09, 2014
Removed the handle with two screws on the inside front and pulled out the custom wood panel. Pulled the compactor out from under cabinet. Tipped it over on back of unit, supporting it with a little foot stool. Unscrewed two lower screws at bottom of unit holding black trim panel (that held wood panel in place) and lower black rubber flap. Removed two screws on lower outside side of unit that held the foot pedal. Slid off black U shaped metal frame from top of compactor towards bottom. Slid on...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2174267
The Wire Shelf is an OEM part for Whirlpool refrigerators. It is designed specifically for the freezer compartment of the refrigerator. It is constructed with wire material to support the weight of various frozen food items without bending or sagging.
Causes of a faulty freezer shelf can include wear and tear over time, damage from heavy or improperly placed items, or bending due to excessive weight.
Symptoms of a bad freezer shelf may include:
- Sagging or bending of the shelf surface
- Instability or wobbling when placing or accessing items on the shelf
- Reduced storage space or difficulty in organizing frozen food
This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
I needed a new shelf for my freezer Michael G. • Toledo , OH • July 22, 2016
I ordered one from you.
Read more
More
$59.95
- Compare At:
-
$71.34
- You Save:
-
$11.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10250570
This cabinet roller assembly supports the refrigerator at the base and lets you roll the unit forward for cleaning or service. Replace a cracked or seized roller to restore smooth movement and a stable, level stance. What it does:
- Supports the refrigerator cabinet and helps maintain proper leveling
- Allows the unit to roll for easier cleaning and servicing
- Replaces worn, cracked, or seized rollers and damaged brackets
- Helps resolve wobbling, uneven stance, scraping noises, or difficulty moving the fridge
What's included:
- One complete cabinet roller assembly
Install notes:
- Disconnect power and turn off the water supply before servicing
- Protect flooring and use a second person or an appliance dolly to safely tilt or move the unit
- Remove mounting fasteners, swap the assembly in the original position, and reuse hardware if applicable
- After installation, level the refrigerator and verify doors close and seal properly
Do-It-Yourself Stories from Customers like You
The plastic left rear wheel was coming apart and needed replacing Gary H. • San Antonio , TX • June 11, 2016
I decided if one needed replacing I might as well both two--made sense to me. None were available locally so I ordered them on-line. Surprisingly they came sooner than I expected. I also found a video on the internet that clearly showed the procedure. The actual repairs took 15 minutes or less. One good suggestion from the video was to run the screw in and out of the wheel bracket before final mounting. The video also suggested putting something under the corner to eliminate tipping. The...
Read more
More
$27.95
- Compare At:
-
$33.26
- You Save:
-
$5.31
Genuine Whirlpool part
By: Whirlpool
Part Number: WP627018
Size: 1/4 inch. Nut for plastic water line.
Do-It-Yourself Stories from Customers like You
Broken y connector off of water valve on amana refridgerator Greg S. • El Dorado Hills , CA • October 19, 2014
Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks.
Read more
More
$11.95
- Compare At:
-
$14.34
- You Save:
-
$2.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2155013
Clip for bottom grill. If your original clip is riveted, order screw WP489478.
Do-It-Yourself Stories from Customers like You
Leaking water filter housing and broken grill cover clips Carl H. • Strongsville , OH • December 04, 2016
Ordered parts, watched the videos on your website. Very simple.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4387911
This push-button door switch senses when your refrigerator door opens and closes to control the interior light. Replace a worn or stuck switch to restore reliable lighting and proper on/off operation when the door moves. What it does:
- Turns the interior light on when the door opens and off when it closes
- Common fix for a light that won't turn on with the door open
- Resolves lights that stay on continuously with the door closed
- Addresses intermittent lighting from a sticking or damaged plunger
What's included:
Install notes:
- Disconnect power to the refrigerator before servicing
- Carefully pry the old switch from the liner; protect the surface to avoid damage
- Transfer wires to the new switch one at a time to maintain correct connections
- Press the new switch fully into place and restore power to test operation
Do-It-Yourself Stories from Customers like You
A failed freezer door switch was causing the fridge to display that the door was open when it was not this caused it to beep at random Kara H. • Charleston , SC • March 08, 2016
We actually were able to determine that one of the freezer switches was bad and taped it down for about 3 days. The beeping stopped. Our fridge has two freezer switches and one fridge side switch. I ordered all three from these guys. They were cheaper than Whirlpool by about $20 for parts and about $15 for shipping. The part numbers had superseded too many times to count, usually that doesn't matter but in this case it did. The new parts were just slightly bigger than the old parts AND...
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: W10136387A
Color: clear. It measures about 6 inches wide by 3-1/2 inches high by 15 inches deep.
Do-It-Yourself Stories from Customers like You
Broken part Donna B. • Waterbury , CT • October 28, 2016
Ordered a replacement part from your on line store.
Read more
More
$11.34
- Compare At:
-
$13.49
- You Save:
-
$2.15
Genuine Whirlpool part
By: Whirlpool
Part Number: WP1106508
This gasket/seal creates a tight barrier between two mating parts in your appliance to prevent leaks and performance loss. Replacing a worn gasket restores proper sealing and helps stop seepage at the joint. What it does
- Forms a reliable seal between components to prevent fluid or air leaks
- Maintains proper operation by keeping the sealed area contained
- Replaces gaskets that are brittle, cracked, flattened, or swollen
- Common signs include residue or moisture around the joint, visible wear on the old gasket, or a loose/poor seal
What's included
Install notes
- Disconnect power and any water or gas supply before servicing
- Note the gasket's orientation; compare old and new parts before installation
- Clean and dry mating surfaces; remove old adhesive and debris
- Seat the gasket evenly; do not overtighten fasteners; test for leaks after reassembly
Do-It-Yourself Stories from Customers like You
Delivery person broke fitting off for the ice maker while removeing our "good" old fridge that was already sold Donald J. • Fremont , MI • October 13, 2014
I ordered the repair parts that Lowes said they couldn't get. I got the parts very fast and only took 5 minutes to get the job done.
Read more
More
$6.42
- Compare At:
-
$7.58
- You Save:
-
$1.16
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:
- Thread-forming Type AB design engages thin metal or plastic components
- Secures panels, brackets, trim, or covers to reduce looseness and vibration
- Replaces missing, stripped, or corroded fasteners
- Helps maintain alignment for proper operation and reduced noise
What's included:
Install notes:
- Disconnect power before servicing; shut off water supply if working near water lines
- Use the correct driver for the screw head; start by hand to avoid cross-threading
- Tighten until snug—do not overtighten to prevent stripping or cracking plastic
- Repair damaged holes or replace worn clips/inserts before installing the new screw
Specs:
- Size: #8-18 x 5/8 in (length 0.625 in)
- Thread type: Type AB, thread-forming
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: 4387491
These inserts are for 1/4 inch plastic tubing. Package of 4.
More
$11.95
- Compare At:
-
$13.22
- You Save:
-
$1.27
Genuine Whirlpool part
By: Whirlpool
Part Number: W11596045
This small plastic control arm extension links to the mechanism it serves, restoring proper movement and engagement so the appliance can operate as intended. It's a simple, direct-replacement component designed to snap in and align correctly.
- Connects to the existing control arm to extend its reach and function
- Helps correct issues like improper engagement or intermittent operation
- Can address symptoms such as sticking, misalignment, or failure to activate
- Sized to fit the original mounting points for consistent motion
What's included: One control arm extension Install notes:
- Disconnect power (and water if applicable) before servicing
- Note the orientation of the original part to match during reassembly
- Inspect the mating control arm and linkage for wear or damage
- Test operation before fully reassembling panels or covers
More
$25.95
- Compare At:
-
$30.88
- You Save:
-
$4.93