Kenmore Dryer 110.78944892 (11078944892, 110 78944892) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP694424
If your dryer won't stay lit or shuts off after a few minutes, the gas limiter may be faulty. This regulator controls safe gas flow to the burner.
Do-It-Yourself Stories from Customers like You
I needed to convert from lp to natural gas Mark S. • Raleigh , NC • June 01, 2015
Removed LP Orifice and LP Gas limiter.
Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP.
I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just...
Read more
More
$26.74
- Compare At:
-
$32.09
- You Save:
-
$5.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3395382
The Start Switch is an OEM replacement part for Whirlpool dryers. It is an electronic component responsible for initiating the heating elements and tumble cycles upon user command from the control panel.
Causes of a bad start switch involve general wear over extended use. Failure of the internal conducting surfaces interrupts circuit activation as well.
Symptoms of a bad start switch include:
- Heating elements or tumble cycles that will not engage properly
- Dryer fails to operate or stops mid-cycle unexpectedly
- Control panel appears non-responsive to selections
- Error codes related to ignition or power delivery faults
Note: This dryer push-to-start switch has 2 terminals.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore electric dryer models.
Do-It-Yourself Stories from Customers like You
Dryer wouln't start heard the timer working but the starter wouldn't start Perry B. • Stockton , CA • December 05, 2014
I replaced the starter switch, that really didn't need to be replaced, and the thermal fuse, which did.
Read more
More
$49.40
- Compare At:
-
$58.29
- You Save:
-
$8.89
Genuine Whirlpool part
By: Whirlpool
Part Number: W11129408
Houses and secures the lint filter in your dryer. Replace if cracked, warped, or broken to prevent lint bypass and maintain airflow. Verify fit by model.
Do-It-Yourself Stories from Customers like You
Dryer lint screen housing was warped. Michael D. • Reno , NV • January 29, 2022
Bought a new lint screen housing and top flapper. Probably didn’t need the flapper but I didn’t want to set into the repair and find out I did need it.
Read more
More
$47.34
- Compare At:
-
$56.81
- You Save:
-
$9.47
Genuine Whirlpool part
By: Whirlpool
Part Number: WP488729
This screw is used to secure the handle end cap to the center of the door. The screw size measures 8-18 x 1/2 inches.
Do-It-Yourself Stories from Customers like You
The lint catch was broken Misti P. • Spokane , WA • January 18, 2019
This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one.
Read more
More
$7.31
- Compare At:
-
$8.70
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3387242
The Front Panel Seal is an OEM replacement part for Whirlpool dishwashers. Measures 24 inches. This seal is located on the dishwasher's front panel and helps prevent water leaks by creating a watertight barrier during the wash cycle. It ensures efficient operation while protecting your kitchen from potential water damage.
Symptoms of a bad Front Panel Seal include:
- Water leaking from the front of the dishwasher during operation
- Visible wear, cracks, or tears in the seal
- Increased noise or vibration due to improper sealing
Causes of a failing Front Panel Seal can include wear and tear from regular use, exposure to high temperatures and moisture, or improper cleaning methods. A damaged seal can compromise the dishwasher’s efficiency and lead to water leakage.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Sold individually, 2 seals are required on front panel.
Do-It-Yourself Stories from Customers like You
Squeaking kenmore dryer that stopped working Paul M. • Norcross , GA • November 28, 2016
First I watched videos about squeaking Kenmore dryers. Then I used that information to open the dryer, diagnosing the fact that the roller on the drum belt tension arm had broken and actually fallen off the arm. The dryer was filled with lint and dust/dirt, so I also saw that the seals on the dryer had deteriorated greatly. AppliancePartsPros website is outstanding, far better than its competitors. This made it easy to find the parts and videos that I needed. It took hours to pull everything...
Read more
More
$19.95
- Compare At:
-
$23.74
- You Save:
-
$3.79
Genuine Whirlpool part
By: Whirlpool
Part Number: W11236646
The washer is an OEM replacement part for Whirlpool clothes dryers. This part is located on the drum roller support shaft in your dryer. The exterior of the washer is 1 inch in diameter with a hole in the middle and is made of metal. They are installed alongside the drum support rollers and idler pulleys. They help prevent the rollers and pulleys from bumping up against the brackets they are installed on. If you are replacing the rollers, we suggest you replace the washers at the same time.
Causes can be normal wear to bearing surfaces over extended use cycles. Accidental impacts may also potentially bend or damage shaft components.
Symptoms of a bad roller shaft include:
- Noisy squeaks or clanks emanating from within
- Jerky or unbalanced tumbling of dryer loads
- Roller assemblies binding or sticking
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Roller broke Art M. • Danville , CA • September 23, 2014
Replaced the roller, shaft, rings and washer. After removing the back, reverse threading the nut off, discarding the old hardware and installing the new hardware back in business in about 20 minutes.
Read more
More
$21.95
- Compare At:
-
$26.34
- You Save:
-
$4.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP234826
Converting dryer from propane to natural gas? This orifice regulates gas flow in the burner assembly. Easy DIY fix, typically done in under 1 hour.
Do-It-Yourself Stories from Customers like You
Propane to natural gas conversion on range and dryer Vincent P. • Howell , NJ • October 09, 2014
Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time.
Read more
More
$27.52
- Compare At:
-
$33.02
- You Save:
-
$5.50
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3388229
The Access Panel Spring Retainer is an OEM part for Whirlpool dryers. This part secures the access panel of the dryer, ensuring it stays in place during operation. The spring retainer provides tension and stability, making it easy to open and close the access panel when maintenance or repairs are needed.
Causes of a bad access panel spring retainer can include regular wear and tear, loss of tension, or physical damage.
Symptoms of a bad access panel spring retainer include:
- Access panel not staying securely closed
- Difficulty opening or closing the access panel
- Loose or rattling access panel during dryer operation
- Visible damage or wear on the retainer
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Dryer no start George Larry B. • Niceville , FL • November 19, 2019
Removed and replaced start switch then motor, no joy. removed the timer for disassembly, found bad contact. soldered contact to the spring tab and assembled and installed the timer. All good now.
Read more
More
$9.41
- Compare At:
-
$11.20
- You Save:
-
$1.79
Genuine Whirlpool part
By: Whirlpool
Part Number: WP308685
Screw secures appliance panels and access covers. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattles or gaps.
Do-It-Yourself Stories from Customers like You
Under the counter mounting brackets were missing Douglas A. • Glen Allen , VA • June 19, 2019
After several attempts at Local Hardware stores and Lowe's and Home Depot to find them I called AppiancePartsPros.com. I gave them the model number and what I was looking for and customer service directed me to the part on the Web site. They were extremely helpful and it was very fast and I got the parts the next day.
Read more
More
$7.31
- Compare At:
-
$8.63
- You Save:
-
$1.32
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3389420
Secures the idler pulley to maintain proper drum belt tension in your dryer. Replace if worn, loose, or causing squealing noises. Confirm fit with your model.
Do-It-Yourself Stories from Customers like You
Loud squealing noise when dryer (Whirlpool) is turned on Marc P. • Chesterfield , MI • December 31, 2018
Using You Tube How-To Videos.
Replaced the drum drive belt and tensioner pulley/arm (including) the spring.
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP90767
The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.
This part fixes the following symptoms:
- Loose or wobbly components within the appliance
- Panels or parts that are not securely attached
- Rattling or unusual noises due to loose parts
- Damaged or missing screw
The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
Do-It-Yourself Stories from Customers like You
Certain buttons were'not working Brent T. • Easton , MD • November 17, 2014
One day my wife went to bake something and the bake/broil buttons as well as #3, #9, and oven light ceased to work. Local repair guy came by and wanted to charge $500 to fix it....YEAH RIGHT! Did a little homework and found this website, spoke with knowledgable staff who pointed me in the right direction. Took me all of about 20 minutes to install new control panel..everything works perfect...THANKS!
p.s. In doing my research come to find Maytag did little to insulate control panel from oven...
Read more
More
$7.31
- Compare At:
-
$8.70
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP694422
Spring installs inside the gas pressure regulator assembly on gas dryers. Replace if lost during conversion between natural gas and propane fuel types.
Do-It-Yourself Stories from Customers like You
I needed to convert from lp to natural gas Mark S. • Raleigh , NC • June 01, 2015
Removed LP Orifice and LP Gas limiter.
Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP.
I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just...
Read more
More
$17.48
- Compare At:
-
$20.80
- You Save:
-
$3.32
Genuine Whirlpool part
By: Whirlpool
Part Number: WP694423
Dryer making high-pitched sound when igniter turns on? This natural gas regulator maintains proper gas pressure to burners. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
I needed to convert from lp to natural gas Mark S. • Raleigh , NC • June 01, 2015
Removed LP Orifice and LP Gas limiter.
Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP.
I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8566209
Seals the joint between the lint screen housing and blower assembly. Replace when worn to prevent lint buildup in cabinet. Confirm fit by model number.
Do-It-Yourself Stories from Customers like You
Over heating. Robert B. • Hollywood , SC • October 14, 2017
Watched You tube videos to narrow the problem down to old deteriorated gaskets.
Read more
More
$37.95
- Compare At:
-
$45.54
- You Save:
-
$7.59
Genuine Whirlpool part
By: Whirlpool
Part Number: WP388326
This console screw secures the control console to the appliance cabinet or top, keeping the panel tight and aligned. Replace a missing or damaged screw to stop panel wobble and rattling and maintain a snug, stable fit. What it does:
- Fastens the control console/control panel to the cabinet or top panel
- Helps maintain alignment and reduces vibration and rattling
- Replaces a missing, stripped, or rusty original screw
- Common fix for a loose or lifting console/panel
What's included:
Install notes:
- Disconnect power before service; if applicable, shut off gas/water
- Support the console to avoid straining wiring harnesses
- Start threads by hand to prevent cross-threading; tighten until snug—do not overtighten
- Use the correct driver style for your model's hardware
Do-It-Yourself Stories from Customers like You
Leaking water from the tub seal David C. • Bessemer City , NC • January 27, 2018
THIE REPAIR WAS ON A WHIRLPOOL TOP LOAD WASHING MACHINE
At first I suspected the leak was from the pump because I had replaced the pump 2 times over 10 years. This time with the cabinet removed and filling the tub with water, I saw water running down one of the steel support arms that go under the tub, so I was guessing that it was coming from the tub seal. I had to use a jumper wire to bypass the Lid Switch so the water would drain.
Several months before I had this issue with the water leaking...
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP693140
If your dryer won't heat or flame won't stay lit, a corroded burner tube may be the cause. This assembly includes an adjustable air shutter for proper combustion.
Do-It-Yourself Stories from Customers like You
Dryer not heating Ray M. • Marissa , IL • October 03, 2014
I removed the kick panel/door and confirmed there was no flame. Inspection with a flashlight revealed the igniter was damage - partly broken away. Using a 1/4" socket set I removed the burner assembly. Inspection showed the burner was rusted and the flame deflector had fallen off. I ordered both the "Dryer Igniter and Bracket" and a burner. They arrived in about three days. I had to attach the igniter to the bracket (one screw) and then the bracket to the burner (one screw). The only...
Read more
More
$85.38
- Compare At:
-
$102.46
- You Save:
-
$17.08