Kenmore Dryer 110.96502810 (11096502810, 110 96502810) Parts

Dryer humming but not starting? This drive motor rotates the drum and blower wheel. Moderately difficult repair requires drum removal. Fix it today.

This small retaining clip secures the door hinge in place so the door opens and closes smoothly and stays properly aligned. Replacing a worn or missing clip helps restore reliable hinge support and consistent door operation.

• Retains the hinge/hinge pin to prevent shifting or separation
• Helps maintain door alignment to avoid rubbing, sagging, or binding
• Replaces a clip that is bent, cracked, corroded, or missing
• Common signs it's needed: loose or wobbly door, difficulty closing, misaligned door, visible damaged/missing clip

• Unplug the appliance and, if applicable, remove items from the door to reduce weight
• Support the door before working on the hinge
• Remove any hinge cover/fasteners, swap the clip, and ensure it seats fully
• Reassemble and check door alignment and smooth operation

This internal-bias thermostat controls exhaust temperature in your dryer, cycling the heat on and off to maintain proper drying temperatures. Replacing a failed thermostat can restore consistent drying performance and help protect the dryer from overheating shutdowns.

• Monitors exhaust air temperature and opens/closes the heating circuit to regulate heat
• Provides the bias function used by automatic cycles for correct temperature control
• Failure symptoms can include no heat or low heat, long dry times, overheating or high-limit trips, and inconsistent cycling temperatures
• Helps prevent thermal cutoffs caused by restricted airflow or faulty temperature regulation

• Disconnect power before servicing; for gas models, also shut off the gas supply
• Access location is typically on the blower/exhaust housing; note wire positions and transfer one at a time
• Ensure the thermostat mounts flush for proper sensing; tighten screws securely
• After replacement, verify good airflow and clear venting to prevent repeat failures

Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
• Helps maintain alignment and secure attachment during operation
• Replaces stripped, rusted, or missing hardware
• Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment

• Disconnect power (and shut off gas, if applicable) before servicing
• Match screw length and thread to the original for proper fit
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Support the part being fastened to keep alignment while tightening

Vinyl door seal creates an airtight barrier to maintain proper temperature and prevent energy loss. Replace when worn, cracked, or causing drafts.

3 pin 60 minute

6-20 screw secures panels, brackets, and internal components. Replace stripped, missing, or damaged screws to restore proper fit and eliminate rattling.

This is a small lever or catch that engages the door switch when the dryer door is closed, signaling the dryer that it is safe to operate. It also interacts with the belt switch mechanism to detect proper belt tension. Replace this part if the dryer does not start when the door is shut, runs with the door open, or if the lever is visibly broken or worn.

Almond. Size: 13 oz. can. Acrylic appliance paint.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

This front drum bulkhead is the stationary front panel that supports the dryer drum and seals the drum opening to maintain proper airflow and drum alignment for reliable drying performance. What it does:

• Provides a mounting surface and seal for the front of the dryer drum to help maintain correct drum alignment
• Directs airflow from the drum into the exhaust plenum for consistent drying
• Reduces rubbing and wear on the drum edge and front roller or glide surfaces
• Can help stop visible grinding, scraping or excess vibration when worn or cracked

• One front drum bulkhead

• Turn off power and disconnect the dryer before beginning service
• Handle plastic parts carefully to avoid cracking; check surrounding seals and rollers during replacement
• Some models require removal of the front panel and drum for access; keep fasteners organized for reassembly

Touch-up paint for appliances in almond color. Repairs chips, scratches, and worn spots on ovens, refrigerators, microwaves, and dryers.

Dryer timer stuck or not advancing through cycles? The timing cam controls cycle progression. Worn cams cause timers to stall mid-cycle or fail to move.

Replacement dryer drum front bulkhead panel. Installs at the front of the drum assembly. Needed when cracked, warped, or damaged from wear.

This screw-washer assembly secures panels, brackets, and other appliance components. The integrated washer spreads load and resists loosening, so replacing a worn or missing fastener restores a tight, reliable fit and helps eliminate rattles.

• Provides fastening with a built-in washer for even clamping and retention
• Replaces missing, stripped, or corroded hardware
• Helps address loose panels/handles and vibration or rattle noises
• Supports proper alignment of covers, brackets, and trim

• Disconnect power and shut off water or gas (as applicable) before servicing
• Match to the original fastener; location and quantity in your model's parts diagram
• Start threads by hand to avoid cross-threading; tighten with the correct driver
• Do not overtighten; replace other severely rusted or damaged fasteners in the same area