Kenmore Dryer 110.C79722800 (110C79722800, 110 C79722800) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8312709
The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment.
Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.
Symptoms of a bad clip include:
- Loose console assembly that is not securely fastened
- Misaligned or dangling controls that do not sit flush
- Dislodged console at risk of detaching from housing
- Missing clip leaving an open mounting point
This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
My kenmore washer model 11029828801 was agitating during the fill cycle and the tub would only partially fill also at the end of the spin cycle rinse water was spraying in resoaking the clothes Jay S. • Hammond , IN • February 07, 2017
I read the FAQ section of Appliance Pros parts web site. I found out I needed to replace the temperature control switch, WPW10248240, to correct my problem. This switch also controls the tub filling water level based on air pressure via the attached vinyl tubing. I ordered the switch and the tubing, WP353255, in case mine was no longer any good, and I also ordered the retaining clips for the control cabinet, (2) of WP8312709, because they can be damaged when accessing the controls. My new...
Read more
More
$19.95
- Compare At:
-
$23.74
- You Save:
-
$3.79
Genuine Whirlpool part
By: Whirlpool
Part Number: 280119
This genuine OEM replacement part is a burner and gas valve assembly for dryers. The burner and gas valve assembly is a complete assembly that contains the burner that distributes the gas in a way that creates an even flame allowing for heat to be distributed properly to perform the dryer's essential function. If the dryer is no longer drying clothes effectively or heating properly, then it might be time for it to be replaced. Luckily repairing a gas valve assembly is a relatively simple job.To replace the burner and gas valve assembly, begin by shutting off power to the appliance. Next, pull the dryer away from the wall to gain access to the back panel. Remove the back panel and locate the burner and gas valve assembly. Remove the mounting screws that hold it in place. After removing the screws use both hands to pull and release the old burner assembly. Set it off to the side and proceed to install the new one by refastening the screws that hold it in place.This replacement part is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand washers.
Do-It-Yourself Stories from Customers like You
Weak or no burner flame Michael T. • North Reading , MA • November 16, 2018
Unfortunately my first repair attempt (replacing the Gas Valve Coils) failed so I decided to replace the entire Burner assembly. From a cost/time point of view the Burner assembly is a better value than just buying the Gas Valve seeing as you don't have to disassemble/reassemble most of the existing Burner (to get to the Gas Valve) *and* you get a new Igniter!! The most annoying thing about the repair is accessing the screw that clamps the gas pipe to loosen it :-(...
Read more
More
$230.50
- Compare At:
-
$274.30
- You Save:
-
$43.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10080190
This 3/8-16 nut secures appliance components and helps prevent loosening and vibration. Replace a worn, stripped, or missing nut to restore a tight, reliable connection and consistent operation.
- Provides a 3/8-16 threaded fastener connection for applicable bolts or studs
- Helps keep brackets, panels, and other parts firmly in place
- Replaces damaged or missing hardware that can cause looseness or rattling
- Signs of failure include rounded corners, stripped threads, corrosion, or inability to tighten securely
What's included: 1 nut Installation notes:
- Disconnect power and, if applicable, shut off water and gas before servicing
- Match thread size to the original part; start threading by hand to avoid cross-threading
- Reinstall any washers/spacers in the original order; tighten securely without over-tightening
- If the original used a locking feature or threadlocker, reinstall per your product's service information
Do-It-Yourself Stories from Customers like You
Needed to replace a left thread nut Russell C. • Elizabeth , IN • September 24, 2021
I ordered the nut and was shocked when it arrived the next day.
Read more
More
$7.31
- Compare At:
-
$8.77
- You Save:
-
$1.46
Genuine Whirlpool part
By: Whirlpool
Part Number: WP693140
If your dryer won't heat or flame won't stay lit, a corroded burner tube may be the cause. This assembly includes an adjustable air shutter for proper combustion.
Do-It-Yourself Stories from Customers like You
Dryer not heating Ray M. • Marissa , IL • October 03, 2014
I removed the kick panel/door and confirmed there was no flame. Inspection with a flashlight revealed the igniter was damage - partly broken away. Using a 1/4" socket set I removed the burner assembly. Inspection showed the burner was rusted and the flame deflector had fallen off. I ordered both the "Dryer Igniter and Bracket" and a burner. They arrived in about three days. I had to attach the igniter to the bracket (one screw) and then the bracket to the burner (one screw). The only...
Read more
More
$85.38
- Compare At:
-
$102.46
- You Save:
-
$17.08
Genuine Whirlpool part
By: Whirlpool
Part Number: 279782
Dryer won't start but has power and timer works? This belt switch kit stops the dryer when the belt breaks. Moderate DIY repair, 45-60 minutes.
Do-It-Yourself Stories from Customers like You
Broken belt switch Jack F. • Hermosa Beach , CA • July 08, 2016
Every time I tried to start our dryer, the "Sensing Light" came on, I heard a little "click," and the dryer would not start.
According to the very helpful Appliance Parts Pros. videos, I was able to dismantle, diagnose a few components, and discover the broken part. In this case, it was a Broken Belt Switch.
I ordered the part, we went on vacation for a week, and when we returned home the part was at our residence. The next day, I installed the part and all is good now.
I am nearly 70 years...
Read more
More
$52.95
- Compare At:
-
$63.01
- You Save:
-
$10.06
Genuine Whirlpool part
By: Whirlpool
Part Number: WP693995
This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.
Do-It-Yourself Stories from Customers like You
There was no power cord and accessories to attach it Terry C. • Martin , TN • December 27, 2016
I put all pieces that I ordered on the dryer and plugged it in.
Read more
More
$7.31
- Compare At:
-
$8.70
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP681414
Specs: 10-16 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Dryer drum was beginning to stall occasionally Dana J E. • San Marcos , CA • March 17, 2015
After shopping for a new Whirlpool Thin Twin Stack, Found appliance parts pros online and decided to take it apart to see if repair was a possibility. APPro's online instructions were easy to follow, in a couple hours it was apart, and I placed the order. Reg ground took a week from NY, so the laundry piled up that week. The parts arrived on Monday morrning, by afternoon the machine was running like new! The cause was the belt tensioner pulley had frozen. Replaced it, drum wheels,snap...
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: W10470674
Side or bottom exhaust vent kit for dryers. Relocates dryer vent from rear to side or bottom position. Includes metal duct, hardware, and instructions.
Do-It-Yourself Stories from Customers like You
Needed to switch dryer to side exhaust Allen B. • Clarksville , IA • January 23, 2015
Went on line looking on how to accomplish this and Appliance parts pro site came up and it was exactly what I needed. Order was sent on Sunday note and on Tuesday afternoon it was delivered.
Just got done installing. Took longer to gather up the needed tools then to install. The instructions were awesome . complete wife great photos
Read more
More
$70.34
- Compare At:
-
$84.41
- You Save:
-
$14.07
Genuine Whirlpool part
By: Whirlpool
Part Number: W11226088
Covers and protects your dryer's light bulb from heat and debris while diffusing illumination. Replace if cracked, yellowed, or missing. Confirm fit.
Do-It-Yourself Stories from Customers like You
The pulley wheel the light cover James B. • Philadelphia , PA • August 06, 2017
Been doing these repairs for a lil while now. Your Company provides Videos on Appliance Brands that detail how to get to the part that is suspected and how to Test and Repair. I suspected a Part by it's sound and followed the Video to get to the part and made the repair.
Read more
More
$26.21
- Compare At:
-
$31.45
- You Save:
-
$5.24
Genuine Whirlpool part
By: Whirlpool
Part Number: WP297092
This small retaining clip secures the door hinge in place so the door opens and closes smoothly and stays properly aligned. Replacing a worn or missing clip helps restore reliable hinge support and consistent door operation.
- Retains the hinge/hinge pin to prevent shifting or separation
- Helps maintain door alignment to avoid rubbing, sagging, or binding
- Replaces a clip that is bent, cracked, corroded, or missing
- Common signs it's needed: loose or wobbly door, difficulty closing, misaligned door, visible damaged/missing clip
What's included: 1 hinge clip Install notes:
- Unplug the appliance and, if applicable, remove items from the door to reduce weight
- Support the door before working on the hinge
- Remove any hinge cover/fasteners, swap the clip, and ensure it seats fully
- Reassemble and check door alignment and smooth operation
Do-It-Yourself Stories from Customers like You
Dryer no start George Larry B. • Niceville , FL • November 19, 2019
Removed and replaced start switch then motor, no joy. removed the timer for disassembly, found bad contact. soldered contact to the spring tab and assembled and installed the timer. All good now.
Read more
More
$10.95
- Compare At:
-
$13.03
- You Save:
-
$2.08
Genuine Whirlpool part
By: Whirlpool
Part Number: W11222083
This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.
- Supplies AC power from the wall outlet to the appliance's electrical system
- Helps resolve no power, intermittent power loss, or tripped breaker issues
- Replace if the cord is cut, frayed, melted, discolored, or feels hot at the plug
- Restores safe operation when the original plug or insulation is damaged
What's included: 1 power cord Install notes:
- Disconnect power at the outlet or circuit breaker before servicing
- Note wire routing and connection points; match the original orientation for hot, neutral, and ground
- Seat the cord properly and secure with the model's required strain relief or clamp to prevent tension on terminals
- Ensure the cord is not pinched and is clear of sharp edges, hot surfaces, and moving parts; test for proper operation
Do-It-Yourself Stories from Customers like You
New cord Michael C. • Bakersfield , CA • May 10, 2021
Thanks to you, all went well. No problems.
Read more
More
$67.69
- Compare At:
-
$81.23
- You Save:
-
$13.54
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: W10850756
Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: W11222846
Dryer lint screen door provides access to the lint filter. Replace if cracked, broken, or won't close properly. Verify fit with your model number.
Do-It-Yourself Stories from Customers like You
Broken parts Joao L. • Albertson , NY • February 16, 2020
Changed the old parts with the new ones.
Unscrewed one side. The other side was broken
Put the new parts together and screwed back into place
Done. Everything works
Read more
More
$91.95
- Compare At:
-
$110.34
- You Save:
-
$18.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10549550
Replaces the front pull on drop-down hamper-style dryer doors. Restores a comfortable grip when your original handle is cracked, loose, or missing.
Do-It-Yourself Stories from Customers like You
Clothers dryer door handle was broken Mike R. • Bartlett , TN • July 13, 2015
Bought a replacement part and put it in myself. I took the door and the old one snapped out and the new one snapped in.
Read more
More
$6.67
- Compare At:
-
$7.94
- You Save:
-
$1.27
Genuine Whirlpool part
By: Whirlpool
Part Number: 4392899
Touch-up paint for appliances. Covers chips, scratches, and worn areas on range tops, refrigerators, and other appliances. Includes brush applicator.
Do-It-Yourself Stories from Customers like You
Lack of accurate control on 2 electric range burners Jeff D. • Neenah , WI • April 09, 2016
Ordered 2 infinite burner controls from Appliance Parts Pros and watched the online video on the replacement of them at the same time. When they arrived promptly, I was ready to take on the job.
The fix only took about 15 minutes because I was prepared after watching the video.
Read more
More
$17.95
- Compare At:
-
$21.18
- You Save:
-
$3.23