Kenmore Refrigerator 253.44382407 (25344382407, 253 44382407) Parts

This damper actuator controls the air damper that directs cold air between compartments, helping maintain consistent temperatures. Replacing a worn actuator restores regulated airflow and reduces uneven cooling or temperature swings. What it does:

• Moves the air/damper door to open or close the airflow path between freezer and fresh-food sections.
• Helps balance compartment temperatures by adjusting how much cold air is shared.
• A failing actuator can cause uneven cooling, temperature fluctuations, or reduced cold air in the fresh-food compartment.
• May make clicking noises or show no damper movement when faulty.

• Disconnect power to the appliance before starting any service.
• Access typically requires removing the damper housing or control cover in the fresh-food compartment.
• Align the actuator shaft with the damper linkage, seat the gear, and reconnect the electrical connector — do not force parts.

Freezer drain tube that channels defrost water from the drain pan to the drip pan. Replace if cracked, leaking around the grommet, or causing floor leaks.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Small spring that provides return tension for refrigerator actuator lever mechanisms. Replace if spring is broken, stretched, missing, or lost during repair.

Seals the air damper opening to maintain proper airflow between compartments. Replace if torn or compressed to fix uneven cooling and drafts.

Water inlet tube connects the water valve to your ice maker. Replace if cracked, leaking, or damaged. Installs at the back of your refrigerator.

Color: White

Seals internal refrigerator components to prevent air leaks and moisture intrusion. Replace when worn to maintain proper airflow and temperature control.

Replace your refrigerator's water inlet tube when cracked, split, or leaking. Connects water inlet valve to internal filter or dispenser system.

Spacer that fits between refrigerator door hinge components to maintain proper clearance and alignment. Replace if worn, cracked, or missing.

Specs: 1.40`` long

Forms an airtight seal between freezer door and cabinet. Replace when worn or damaged to prevent warm air leaks, frost buildup, and temperature issues.

Replacement fill tube that directs water from the inlet valve into your refrigerator's icemaker mold. Replace if cracked, damaged, or causing leaks.

This door hinge pin forms the pivot for the refrigerator door hinge, keeping the door supported and aligned. Replacing a worn or missing pin restores smooth door movement and consistent sealing.

• Acts as the hinge's pivot shaft to support the door
• Helps maintain door alignment so the gasket can seal properly
• Reduces wobble and scraping at the hinge point
• Typical failure symptoms: door sagging, misalignment, poor closing, or a loose/wobbly hinge

• Unplug the refrigerator and remove items from the door to reduce weight.
• Support the door; remove hinge cover and screws, then lift the door off the hinge.
• Replace the hinge pin in the hinge bracket; transfer any existing spacers/bushings as designed.
• Reinstall and align the door; tighten hardware and verify smooth operation and seal contact.

Replacement drip pan that captures defrost runoff and other liquids beneath the appliance, helping prevent puddles and odors. Fits into the base to restore proper fluid collection and reduce leaks. What it does:

• Collects and channels moisture and defrost water away from the cabinet to prevent pooling under the unit.
• Helps reduce musty odors and water damage caused by a cracked, warped, or missing pan.
• Supports bottom components and maintains proper clearance where applicable.
• Works with the appliance's existing drain path; a damaged pan can cause visible leaks or puddling.

• Disconnect power and remove any food or items from the appliance before starting.
• Access may require removing lower access panels or the toe kick; follow your model's service instructions.
• Inspect mounting tabs and surrounding seals; ensure the pan seats flat and the drain path is clear.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.