Kenmore Refrigerator 253.6088740G (2536088740G, 253 6088740G) Parts

The bar retainers just snapped in and the door handle can be replaced with three screws. Took about 5 minutes total. Read more

This door gasket presses into slot around door pull off old and press in new a five minute repair Read more

The bar retainers just snapped in and the door handle can be replaced with three screws. Took about 5 minutes total. Read more

Part arrived in two days from order placement. Opened package , replaced glass insert in refrig. Took about 30 seconds. Thank you for the prompt service. Read more

• Frost buildup
• Fridge runs too long
• Freezer too cold
• Freezer not defrosting

My problem first showed up as varying temperature in both sections of my old mid 1970’s Frigidaire model FPCI-170T-7 refrigerator, which is not listed on most appliance repair databases. Running on the warm side from time to time, as well as sudden fan noise (probably the fan blade hitting ice build-up on the evaporator coil) alerted me to a possible defrost system problem, since the compressor was cooling. The evaporator fan eventually failed after a day or so, and a major repair was... Read more

• Freezer not defrosting
• Fridge too warm
• Freezer section too warm

This was a 2000 model so rather than just replace the defrost timer which was visibly burnt on the terminals, we just did everything. The cold control, defrost timer, thermostat, defrost heater and the compressor capacitor were all replaced. I had the same issue on my older unit and tore it apart replacing one item at a time over a three month period so on an older one i suggest do it all while it is apart. Read more

• Won't start
• Too warm
• Fridge too warm
• Freezer section too warm

In short - I replaced the evaporator fan motor and the evaporator fan blade. The Appliance Parts Pros website was extremely helpful to me. Here's how. 1. The site helped me identify that even though my Freezer says it's a Frigidaire, it's actually an Electrolux. 2. The site identified the potential screech causing parts. (I didn't take a chance, I bought all three) It was a worthwhile investment. My freezer is 20 years old so it deserved some help. 3. The site provided guidance videos (not... Read more

Easy : Pulled off old damaged gasket and pushed on new ones. No tools needed Read more

Before we replaced the board, my wife tried to replace just the element. We had one we had ordered several years ago when this same thing happened. When that didn't work we replaced the board and could see where the old board was damaged so we figured this was the solution. It would have been except the bottom element my wife used to replace the old element (which was fine but had been thrown out figuring the new one was new so why keep the old one) was 1" shorter in the back than the old... Read more

• Noisy

1. After hearing a loud noise on the freezer side of unit about halfway up, I started investigating what it could be? My conclusion was evaporator motor or evaporator fan blade. One of the signs of this issue was a distinct change in sound when I opened the freezer door. I ordered a new motor and blade, not knowing exactly what it was. 2. I couldn't get water to dispense, so I changed the filter and that wasn't the problem. I ordered a water valve and crossed my fingers. These parts arrived... Read more

I removed the meat drawer and shelving unit. I unscrewed the Philips head screws on either side of the shelf brackets. I cleaned the old surfaces and fitted the new plastic hangers in place. I screwed the new hangers in place with the screws I had from the old ones. It was very easy, except the holes in the plastic hanger are not quiet big enough for the screws. I had to push very hard with the screwdriver, and started to strip the head of the screw as well at the screwdriver itself. I did... Read more

This was a 2000 model so rather than just replace the defrost timer which was visibly burnt on the terminals, we just did everything. The cold control, defrost timer, thermostat, defrost heater and the compressor capacitor were all replaced. I had the same issue on my older unit and tore it apart replacing one item at a time over a three month period so on an older one i suggest do it all while it is apart. Read more

The bar retainers just snapped in and the door handle can be replaced with three screws. Took about 5 minutes total. Read more

I ordered three parts for my fridge. The entire process was so easy! I entered my model number and quickly found the parts I needed! Submitted the order and the parts arrived the Next Day! I was very happy! Read more

• Door won't open or close

I put a piece of two-by-four, (2"x4") about 10-inches long on edge under the door to support the door. I removed the 3-bolts attaching the door hinge at the bottom corner. I then slid the washer onto the post and placed the bracket back in place with the 3-bolts. That did the trick. I used a 3/8-inch socket with extension and a ratchet. Read more

• Door won't open or close

My 10 year old frig door was hanging down to the point it wasnt fully closing and sealing unless you picked up on it. I ordered a lower hinge bracket, upper and lower bearing, and spacer. My bracket was bent down a little due to my kids hanging on the door when looking at the bottom shelf and i discovered my bracket was held on by only two bolts when there was supposed to be three. I ordered a bolt too. I was able to remove the bottom hinge, remove door to replace upper and lower bearing and... Read more