Kenmore Refrigerator 363.58572892 (36358572892, 363 58572892) Parts
Genuine Ge part
By: Ge
Part Number: WR01X10618
This screw fastens appliance panels, brackets, and trim so parts stay secure and aligned. Replace a missing, stripped, or rusty screw to stop rattles and restore a tight, factory fit.
- Secures covers, brackets, and trim to the appliance cabinet or liner
- Replaces missing, stripped, or corroded hardware
- Helps reduce vibration noise and loose or misaligned parts
- Maintains proper fit of guards, kickplates, or internal panels
Includes: 1 screw
- Disconnect power; turn off water supply if working near water lines
- Match to the original fastener to size and thread
- Start threads by hand to avoid cross-threading; tighten snugly, not excessively
- If threading into plastic, avoid overtightening to prevent damage
Do-It-Yourself Stories from Customers like You
Ice dispenser wouldn't dispense ice Chris K. • Felton , DE • April 29, 2025
The auger gearbox shaft had a spot that was stripped of threads which prevented the auger drive from spinning the ice down the chute. I replaced the auger motor/gearbox assembly, the auger drive as it had to be cut off the shaft, and the 3 mount bolts that hold it all in place. Whole job took 30 minutes from start to finish which included cutting off the drive bracket.
Read more
More
$7.37
- Compare At:
-
$8.36
- You Save:
-
$0.99
Genuine Ge part
By: Ge
Part Number: WR07X10099
This PTCR is the compressor's start device for select refrigerators. It helps the compressor start smoothly by momentarily boosting the start winding, then automatically reduces current as the motor reaches speed.
- Provides initial start assist to the compressor, then self-resets
- A failing PTCR can cause clicking, repeated start attempts, warm temperatures, or the compressor not running
- Helps protect the compressor by limiting inrush current during startup
What's included: One PTCR start device only Install notes:
- Disconnect power before servicing; allow components to cool
- Note wire positions and orientation before removal
- Inspect compressor terminals for heat damage and ensure firm connections
- If the old device shows signs of overheating, also check the overload and wiring
Do-It-Yourself Stories from Customers like You
Refrigerator not getting cold at all and everything thawing out compressor clicking Victor F. • West Milford , NJ • June 15, 2015
I researched the problem and determined that the only thing that can cause this was compressor bad or not starting. Since it was cold the day before I felt it had to be the starter parts and ordered them. It was also very important to clean the coil which I believe caused the over heating.
Read more
More
$72.34
- Compare At:
-
$86.81
- You Save:
-
$14.47
Genuine Ge part
By: Ge
Part Number: WR2X4754
This clamp secures small hoses or tubing and nearby wiring inside the appliance to keep lines held in place and reduce rubbing, leaks, or vibration noise. It's a direct-fit replacement designed to restore proper hose routing and stability. What it does:
- Holds water, drain or vent tubing securely to prevent sagging and rubbing that can cause leaks or wear
- Keeps hoses and wires aligned to reduce vibration and rattling during operation
- Helps maintain proper connections at fittings so seals stay seated and drip risk is minimized
- Simple mechanical clip action — no special tools or adhesives required
Install notes:
- Disconnect power and shut off the water supply before starting any repair
- Remove the old clamp and install this clamp in the same orientation; tubing sits fully in the fitting
- Use standard pliers (or the OEM-recommended tool) to compress/seat the clamp; avoid twisting or pinching the tubing
- Inspect surrounding tubing and fittings for wear; replace damaged hoses or seals if found
Do-It-Yourself Stories from Customers like You
Had a cracked plastic ice maker inlet water tube that flooded part of kitchen floor Terry C. • Durham , NC • February 16, 2019
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,...
Read more
More
$6.95
- Compare At:
-
$8.36
- You Save:
-
$1.41
Genuine Ge part
By: Ge
Part Number: WR57X57
Nut for 1/4 inch tubing.
Do-It-Yourself Stories from Customers like You
Frigidaire refrigerator model FRS3HR5HMB5 having issues with ice buildup around the evaporator fan have had similar issue for three to four years Keith C. • Cypress , TX • November 12, 2018
Changed the Frigidaire Icemaker Fill Tube Part # 241796405 (AP5671747) about a week ago and so far the Frigidaire Refrigerator seems to work fine. Did not use other ordered parts. Recently ice formed around internal evaporator fan and it started making loud noise when then fan and compressor, etc were running. A long winded history noted below if interested:
I have been fighting with this Frigidaire Refrigerator for about 3 to 4 years, started out with the evaporator fan making noise when ice...
Read more
More
$7.37
- Compare At:
-
$8.36
- You Save:
-
$0.99
Genuine Ge part
By: Ge
Part Number: WR1X1367D
Includes 12 retainer rings.
Do-It-Yourself Stories from Customers like You
A fin on the plastic auger broke off and needed to be replaced John M. • Massanutten , VA • August 08, 2015
I ordered a replacement auger from AppliancePartsPros.com. Upon receipt of the new auger, I watched the repair video and took the ice crusher apart. I found several other parts that needed to be replaced as well. Once All the parts were received, I again watched the video. The video was not specific enough to show how to reassemble the ice crusher blades and the two types of washers. I found another video on YouTube that walked me through specific details of assembly and everything went...
Read more
More
$12.95
- Compare At:
-
$15.41
- You Save:
-
$2.46
Genuine Ge part
By: Ge
Part Number: WR1X5278
This cable clamp secures refrigerator wiring to the cabinet, keeping harnesses organized and protected. Replacing a missing or damaged clamp helps prevent chafing and vibration noise while maintaining proper clearance from fans and other moving components.
- Anchors wire harnesses in their designed routing
- Helps prevent insulation wear from rubbing or vibration
- Keeps wires clear of sharp edges and moving parts
- Common signs it's needed: missing/broken clamp, loose or dangling wires, or new rattling/buzzing noises
What's included: 1 cable clamp Install notes:
- Disconnect power before servicing
- Access the clamp location and note original wire routing
- Position the clamp and secure with the existing fastener; do not overtighten
- Ensure wires aren't pinched and have clearance from the fan/compressor before restoring power
More
$7.37
- Compare At:
-
$8.36
- You Save:
-
$0.99
Genuine Ge part
By: Ge
Part Number: WR2X7309
This solenoid saddle is a small mounting bracket that secures a refrigerator solenoid in the correct position. By preventing movement and misalignment, it helps the linked mechanism engage smoothly and consistently.
- Secures the solenoid to its housing or frame to prevent shifting
- Maintains proper alignment for reliable actuation
- A worn or broken saddle can cause buzzing/chattering and intermittent operation
- Restores stable mounting to help the connected mechanism work correctly
What's included: 1 solenoid saddle Install notes:
- Disconnect power; shut off water supply if working near water lines
- Access the solenoid assembly and note the original saddle's orientation
- Transfer the solenoid into the new saddle and reuse existing fasteners/clips
- Smooth operation before reassembling panels
Do-It-Yourself Stories from Customers like You
Ice dispenser crushing ice only no cubes Eric W. • Copper Canyon , TX • June 27, 2014
Easy fix once I found the problem. Broken solenoid sleeve. Part cost $2.58 + shipping. 10 minute repair.
Read more
More
$6.72
- Compare At:
-
$8.36
- You Save:
-
$1.64
Genuine Ge part
By: Ge
Part Number: WR01X10652
Specs: 8-18 AB IHW 5/8 S
Do-It-Yourself Stories from Customers like You
This is the third time i have had to replace the "evaporator fan" in my ge refridgerator Leroy S. • Roseville , MN • December 07, 2014
Because I have had to replace this fan before, the process goes pretty fast.. I am impressed with AppliancePros for a number of reasons, the price for componets is always cheaper that other major parts suppliers. They go to great length to insure all ordered parts are shipped and in a timely fashion.. Also the live tutorials are a great help for the Doit yourselfer..
Read more
More
$7.95
- Compare At:
-
$9.38
- You Save:
-
$1.43
Genuine Ge part
By: Ge
Part Number: WR87X10226
Do-It-Yourself Stories from Customers like You
Bad compressor Harvey K. • Reno , NV • October 10, 2016
Hired a repair professional. This is an expensive fridge so I wanted to repair rather than replace.
The estimated cost for the repair was quite high, but at least it was itemized. I went on-line and found Appliance Parts Pros, and bought the major plus one minor part from them. I arranged with my local repair guy to use the parts I bought on-line.
RESULT: I saved $370 by buying my own parts, probably could have saved more with a little more effort. Appliance Parts Pros was easy to deal with,...
Read more
More
$536.95
- Compare At:
-
$642.35
- You Save:
-
$105.40
Genuine Ge part
By: Ge
Part Number: WR17X4207
According to GE you must also replace part number WR17X4341 auger when replacing this part.
Do-It-Yourself Stories from Customers like You
Ice crusher repair GE Monogram counter depth. Glenn J. • El Cajon , CA • July 27, 2020
This was a very easy repair, the on-line video at AppliancePartsPros.com was helpful.
The Helix was spinning freely (meaning, the Auger Blade was not holding it in place on the Auger).
Pulling the assembly apart was a snap, and very logical (the video is perfect if you get lost).
The family is now enjoying both crushed and cubed ice - and the redesign of the Auger Blade seems to prevent clogging in the ice shoot.
Read more
More
Genuine Ge part
By: Ge
Part Number: WD2X5166
Size: 10-16 ab.
Do-It-Yourself Stories from Customers like You
The shaft seal was leaking when dishwasher emptied Joe V. • Medford , NY • February 07, 2016
Ordered the necessary parts to fix it
Read more
More
$7.37
- Compare At:
-
$8.36
- You Save:
-
$0.99
Genuine Ge part
By: Ge
Part Number: WZ4X241D
Includes 12 screws. Size: 8-18 ab.
Do-It-Yourself Stories from Customers like You
We didn't have a power cord for our dryer Heather B. • Dulce , NM • October 27, 2018
Ordered the cord through appliance parts pros, with additional screws and it works! Yay after waiting months and everywhere was out. Thank you.
Read more
More
Genuine Ge part
By: Ge
Part Number: WR23X427
This freezer door light switch turns the interior freezer light on and off when the door opens and closes, restoring proper illumination so you can see contents clearly and avoid wasting food. What it does:
- Activates the freezer interior light when the door opens; deactivates it when the door closes.
- Replaces a worn, stuck or intermittent switch that causes the light to stay on, not turn on, or flicker.
- Fits into the door or cabinet frame mounting and connects to the existing wiring harness for direct replacement.
What's included: One light switch. Install notes:
- Disconnect power to the appliance before starting any repair to prevent shock.
- Typically snaps into place and connects to the factory wiring harness; no special parts required.
Do-It-Yourself Stories from Customers like You
Broken light switch. Tommy J. • Yortown , VA • October 16, 2017
Replaced light switch.
Read more
More
$74.53
- Compare At:
-
$88.69
- You Save:
-
$14.16
Genuine Ge part
By: Ge
Part Number: WR2X7905
Replacement bucket seal that fits around the refrigerator ice bucket to restore a snug fit and help keep ice contained while reducing frost, spills and water pooling. What it does
- Seals the ice bucket to the cabinet/shelf to help keep ice from spilling or shifting.
- Reduces frost build-up and melting around the ice bin area.
- Helps prevent minor water pooling from melting ice.
- Restores proper fit so the bucket sits flush and operates as intended.
What's included Includes: One replacement bucket seal. Install notes
- Disconnect power to the appliance before beginning any service.
- Remove the ice bucket and carefully peel out the old seal; clean the mounting surface of ice, debris and residue.
- Press the new seal into place, making sure it is fully seated and oriented correctly around the bucket.
Do-It-Yourself Stories from Customers like You
The augor in the ice maker was rusty Angie K. • Greenwich , CT • November 15, 2015
Changed the part with SS part.
Read more
More
$10.07
- Compare At:
-
$11.84
- You Save:
-
$1.77
Genuine Ge part
By: Ge
Part Number: WR2X4138
This spacer is a small mounting support used to maintain proper clearance and alignment between refrigerator panels, doors, or components. It helps reduce rubbing, vibration, and noise by restoring correct spacing and fit. What it does:
- Keeps panels, trim, or components spaced correctly to prevent metal-on-metal contact and wear
- Helps align doors and panels for a flush fit and smoother operation
- Reduces vibration and rattling caused by misaligned parts
- Used wherever a fixed clearance or gap is required during reassembly
What's included: One spacer Install notes:
- Disconnect power to the appliance before beginning any service that requires panel or component removal
- Inspect mating surfaces for damage or debris before installing the spacer; replace any damaged fasteners
- Install in the same orientation and location as the original spacer; do not overtighten mounting hardware
More
$14.95
- Compare At:
-
$17.94
- You Save:
-
$2.99
Genuine Ge part
By: Ge
Part Number: WZ5X158D
Size: 8-32 t. Includes 12 screws.
More
$25.57
- Compare At:
-
$30.43
- You Save:
-
$4.86