Kenmore Washer 417.44052401 (41744052401, 417 44052401) Parts

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lif
  Do-It-Yourself Stories from Customers like You The pump hose had a tear in it and the water hoses were in bad shape   Steven V. • El Cerrito , CA • September 21, 2014

  Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more

Washer won't spin or makes loud whining noise? The drive motor powers drum rotation. Moderately difficult repair, takes 30-60 minutes. Video guide available.

Seals hot and cold water connections to your washer's dispenser. Replace if you notice leaking at the inlet assembly. Confirm fit with your model number.

Washer won't start, stops mid-cycle, or displays error codes? The main control board manages all cycle functions. Moderate DIY repair, 30-45 minutes.

This replacement door handle restores a secure, comfortable grip on your front-load washer door. Swap out a cracked or missing handle to open and close the door smoothly and keep laundry moving without hassle.

• Provides the handhold needed to ope
  Do-It-Yourself Stories from Customers like You Broken dryer handle   Michael P. • Reston , VA • March 01, 2021

  Replaced with screwdriver. Read more

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

Washer drum baffle mounts inside the tub to lift and tumble laundry. Replace if cracked, broken, or missing to prevent snags and restore quiet operation.

Shipping bolt kit secures washer tub and suspension during transport. Install before moving to prevent internal damage, then remove before use.

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet pane
  Do-It-Yourself Stories from Customers like You The poorly designed lightweight outer door panel broke at the hinge support area so that the door would no longer line up this is a very fragile part   William R. • Littleton , CO • November 15, 2016

  I replaced the part and instructed users to be very delicate and gentle when closing the door. Read more

This access panel service cover replaces a damaged or missing cover to protect internal components and give technicians safe access for diagnostics and repairs. It restores a finished appearance while preventing dust and debris from entering service areas

Replacement mounting screw for washers and laundry centers. Secures components like pulleys, brackets, and panels. Replace if missing, stripped, or damaged.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

Door hinge that restores proper door alignment and smooth pivoting for your refrigerator. Replacing a worn or bent hinge helps stop door sag, rubbing, and uneven gaps so the door seals and closes reliably. What it does:

• Supports and pivots the r
  This part fixes the following symptoms

  • Lid or door won't close
  • Lid or door will not open

  See more...
  Do-It-Yourself Stories from Customers like You Error code 41 Oh the beeping!   Amy N. • Pike Road , AL • April 15, 2018

  After reading up on the error codes, I found that my constant beeping was telling me that the door was not well latched. My machine is 12 years old and has seen heavy use, including a broken door handle that has been hanging on with copious amounts of duct tape for a while. I replaced the bent door hinge, worn door latch, and the outer handle. The entire repair required ten minutes and a Phillips head screwdriver. Now it works perfectly with NO more beeping!! Thank you AppliancePartsPros!! Read more

This dispenser assembly replaces a worn or damaged refrigerator dispenser to restore reliable dispensing of water and ice. It provides the dispenser housing and interface needed for proper user operation and sealing at the door. What it does:

• Ho
  Do-It-Yourself Stories from Customers like You Would not go through rinse cycle   Donald S. • Cloudcroft , NM • July 31, 2015

  Replaced the water valve assembly. did not really need the dispenser part. problem mainly caused by hard water buildup where the hose connects. also replaced the hoses as they also had some hard water buildup. Read more

Washer air chamber connects the water level pressure switch to the tub. Replace if cracked, kinked, or disconnected causing water level issues.

Mounting bracket secures components inside your laundry center. Replace if bent, broken, or missing to eliminate rattling and restore stability.