Kenmore Washer 417.44152401 (41744152401, 417 44152401) Parts

Fix a broken or missing detergent dispenser cover that's cracked or won't guide proper detergent placement. Simple 5-minute replacement repair.

Washer won't spin or makes loud whining noise? The drive motor powers drum rotation. Moderately difficult repair, takes 30-60 minutes. Video guide available.

Seals hot and cold water connections to your washer's dispenser. Replace if you notice leaking at the inlet assembly. Confirm fit with your model number.

This replacement door handle restores a secure, comfortable grip on your front-load washer door. Swap out a cracked or missing handle to open and close the door smoothly and keep laundry moving without hassle.

• Provides the handhold needed to ope
  Do-It-Yourself Stories from Customers like You Broken handle on my washing machine front loader   Marlene C. • Scottsdale , AZ • May 23, 2015

  Ordered part and husband repaired it. Read more

Secures hoses to pumps, tubs, and valves preventing leaks. Replace if worn, loose, or causing drips during cycles. Confirm fit with your model number.

Washer drum baffle mounts inside the tub to lift and tumble laundry. Replace if cracked, broken, or missing to prevent snags and restore quiet operation.

Shipping bolt kit secures washer tub and suspension during transport. Install before moving to prevent internal damage, then remove before use.

This replacement screw secures appliance panels and components. With a #10-16 thread and 0.75-inch length, it replaces stripped, rusted, or missing hardware to restore a tight, rattle-free fit and reduce vibration and noise.

• Fastens cabinet pane
  Do-It-Yourself Stories from Customers like You Machine was full of water and wouldn't pump it out   Michael Q. • Richmond , IN • November 11, 2017

  Googled the problem, watched videos on Youtube. Took apart machine and tried cleaning filter most people said was the problem. Wasn't anything but a penny in it so that wasn't the problem. I decided the pump must be bad ,the spring for the bellows and the console were broken so I bought those as well. Got the parts put them on and machine filled up with water turned over a few times and then stopped. The only thing else it could be is the fill level sensor or the main circuit board. Ordered... Read more

This access panel service cover replaces a damaged or missing cover to protect internal components and give technicians safe access for diagnostics and repairs. It restores a finished appearance while preventing dust and debris from entering service areas

Replacement mounting screw for washers and laundry centers. Secures components like pulleys, brackets, and panels. Replace if missing, stripped, or damaged.

Machine screw secures panels, brackets, and internal components in washers. Replace missing, rusted, or stripped screws to restore proper fit and alignment.

Door hinge that restores proper door alignment and smooth pivoting for your refrigerator. Replacing a worn or bent hinge helps stop door sag, rubbing, and uneven gaps so the door seals and closes reliably. What it does:

• Supports and pivots the r
  This part fixes the following symptoms

  • Lid or door won't close
  • Lid or door will not open

  See more...
  Do-It-Yourself Stories from Customers like You Error code 41 Oh the beeping!   Amy N. • Pike Road , AL • April 15, 2018

  After reading up on the error codes, I found that my constant beeping was telling me that the door was not well latched. My machine is 12 years old and has seen heavy use, including a broken door handle that has been hanging on with copious amounts of duct tape for a while. I replaced the bent door hinge, worn door latch, and the outer handle. The entire repair required ten minutes and a Phillips head screwdriver. Now it works perfectly with NO more beeping!! Thank you AppliancePartsPros!! Read more

This dispenser assembly replaces a worn or damaged refrigerator dispenser to restore reliable dispensing of water and ice. It provides the dispenser housing and interface needed for proper user operation and sealing at the door. What it does:

• Ho
  Do-It-Yourself Stories from Customers like You Would not go through rinse cycle   Donald S. • Cloudcroft , NM • July 31, 2015

  Replaced the water valve assembly. did not really need the dispenser part. problem mainly caused by hard water buildup where the hose connects. also replaced the hoses as they also had some hard water buildup. Read more

Washer air chamber connects the water level pressure switch to the tub. Replace if cracked, kinked, or disconnected causing water level issues.

Mounting bracket secures components inside your laundry center. Replace if bent, broken, or missing to eliminate rattling and restore stability.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.