Kenmore Washer Dryer Combo 417.97804791 (41797804791, 417 97804791) Parts

This replacement bolt secures internal components in your appliance. A stripped, rusted, or missing bolt can let parts loosen and vibrate; installing a new bolt restores a tight, stable connection for reliable operation.

• Provides a secure, threa
  Do-It-Yourself Stories from Customers like You Leaking washer tub   Hugh S. • Miami , FL • June 25, 2016

  The seal at the bottom of the tub had started to fail. On large loads water would leak so I ordered a new one rubber seal. Getting the trunnion off the transmission shaft was hard as it was calcified and corroded. I used a wire brush to get some of it off and then used a lot of WD-40. The bolt holding the trunnion plate on sheared off when I tried to remove it on one side and the other came out ok (the bolt hole through the trunnion is not threaded so it should slide out once the plate is off... Read more

Replacement suspension spring for washer tub support systems. Restores proper tension when original spring is weakened, broken, or causing tub tilt.

This air duct seal creates a tight barrier between the dryer's lint housing and cabinet. Replacing a worn seal helps prevent air leaks, maintain proper airflow through the lint filter, and restore consistent drying performance.

• Seals the air duc
  Do-It-Yourself Stories from Customers like You Grinding noise coming from stack unit dryer   Daniel B. • Hughesville , PA • August 22, 2023

  Old, unused stack set. Washer was great, dryer was grinding. Started with the mounting bracket/bearing and the belt. The old ones were slightly beatup. Put it back together and the problem persisted. Found the real problem when I pulled apart the blower to get to the motor. The fan had broken fins that had jammed in the side of the blower housing, and the friction had melted through the outer wall of the fan. Got the blower housing from APP, got the fan from a competitors for $30 less. When it... Read more

Dryer not heating or overheating? A faulty temperature control thermostat often causes inconsistent heat cycles. This part regulates dryer temperature.

Replaces damaged or burnt-out dryer interior light assembly. Restores visibility when door opens. Includes bulb and socket. Verify fit by model number.

Seals the blower housing to prevent air leaks and maintain efficient airflow. Replace if torn, damaged, or causing reduced drying performance.

Keep your dryer tumbling smoothly by restoring proper belt tension. This idler spring attaches to the idler arm and maintains tension on the drive belt so the drum turns reliably without slipping or squealing. What it does:

• Applies constant tens

Spacer that positions and cushions the agitator screw in top-load washers. Replace if worn, cracked, or missing to maintain proper agitator alignment.

Washer won't start or advance to spin cycle? A broken lid strike prevents the lock from engaging. Simple 5-minute snap-in fix—just remove two screws.

Replacement mounting screw that fastens panels and components in laundry centers. Needed when original is missing, stripped, or damaged to restore secure fit.

Return spring for washer door lock mechanism. Restores tension so the latch returns to proper position. Replace if worn, missing, or causing loose latch.

Replacement bracket screw for securing internal panels and brackets to your appliance frame. Needed when original screws are stripped, corroded, or missing.

Metal heat deflector that mounts near the dryer heating element. Replace if warped, cracked, or damaged to restore proper heat distribution and protect wiring.

The blower housing assembly encloses the blower wheel and channels air through the unit's coils. Replacing a cracked or warped housing helps restore smooth airflow and reduce blower noise caused by rubbing or misalignment.

• Directs and focuses ai
  Do-It-Yourself Stories from Customers like You Grinding noise coming from stack unit dryer   Daniel B. • Hughesville , PA • August 22, 2023

  Old, unused stack set. Washer was great, dryer was grinding. Started with the mounting bracket/bearing and the belt. The old ones were slightly beatup. Put it back together and the problem persisted. Found the real problem when I pulled apart the blower to get to the motor. The fan had broken fins that had jammed in the side of the blower housing, and the friction had melted through the outer wall of the fan. Got the blower housing from APP, got the fan from a competitors for $30 less. When it... Read more

Fix a washer that won't advance through cycles or stays stuck on one setting. This mechanical timer restores proper cycle sequencing. 1-hour DIY repair.

Suspension spring that supports and stabilizes the wash tub during operation. Replace if broken, cracked, or worn to restore proper tub support.