Kenmore Washer Dryer Combo 417.97804791 (41797804791, 417 97804791) Parts

The Start Switch is an OEM replacement part for Frigidaire dryers. This part initiates the dryer's cycle once the user selects the desired settings. By pressing the start switch, the motor activates, and the drying process begins, ensuring clothes

The Drum Bearing Bracket is an OEM replacement part for Frigidaire dryers. It holds and supports the drum bearing, which allows the dryer drum to spin smoothly during the tumbling and drying cycle.

Causes of failure can be cracking or brea

Dryer drum bearing ball ensures smooth drum rotation. Replace if drum wobbles, squeaks, or won't turn. Confirm fit with your model number before ordering.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Repla
  Do-It-Yourself Stories from Customers like You Grill on air duct had an item melt on to it and partially block air flow   Charles C. • Orchard Park , NY • November 25, 2017

  It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more

This factory clamp secures a hose or tubing connection so it stays tight during normal operation. Replace a worn or rusted clamp to restore a firm hold and help prevent leaks, drips, or accidental disconnections.

• Holds a hose, tube, or duct firm
  Do-It-Yourself Stories from Customers like You Fan making banging sound in housing   Keith N. • Kaukauna , WI • April 25, 2015

  The blower wheel center was worn down and spinning freely on shaft. Removing front covers, controls and brackets gave access to blower, which front half came off removing screws. (One screw underneath bracket) Pushed new blower on. (It's keyed and has small tabs that line up with groove on shaft). Installed clamp, reassembled and tested. Don't forget to pull the plug out before working on any appliance. Read more

Adjustable leveling leg that screws into the washer cabinet to stabilize and level your appliance. Replace if broken, damaged, or missing to prevent rocking.

Washer motor won't start or stops mid-cycle? This motor start capacitor stores electrical energy to start your washer motor. Moderate DIY repair.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lif
  Do-It-Yourself Stories from Customers like You The pump hose had a tear in it and the water hoses were in bad shape   Steven V. • El Cerrito , CA • September 21, 2014

  Unscrewed the front lower panel ( 2 screws ). Disconnected the pump hose clamp and removed the hose. I loosened the lower back panel and pulled out the drained hose from the rear. Replaced with new hose put back clamp and panels. Very easy Read more

Timer won't advance or dryer runs continuously? This timer control restores proper cycle progression in auto and timed modes. DIY-friendly repair.

This gasket is a sealing component used in select appliances. It fits between two mating parts to keep water or air where it belongs, helping prevent leaks and ensuring proper performance. What it does:

• Forms a tight seal between components or housings
• Helps prevent water drips, seepage, or air leaks at the joint
• Maintains correct appliance performance by keeping moisture/airflow contained
• Replace if the gasket is cracked, torn, flattened, or misshapen
• Common signs include residue, moisture, or visible gaps around the seal

• 1 gasket

• Disconnect power; turn off the water supply before servicing
• Note the orientation of the old gasket prior to removal
• Clean and dry the mating surfaces; remove any old gasket residue
• Seat the new gasket evenly without stretching; reassemble and check for leaks or proper seal

For a complete drum bearing and shaft kit order 5303281153.

Includes motor, motor pulley and housing. Motor pulley no longer available separate

Washer won't spin or agitate? Humming motor or clothes staying wet often means a failed drive motor. This repair typically takes 15-60 minutes with basic tools.

Fix a washer that won't drain or makes whining sounds with this pump and motor assembly. Common causes: debris lodged in pump or burned-out motor.

Connects washer outer tub to drain pump, channeling water out during drain cycle. Replace if cracked, leaking, deteriorated, or damaged by pests.

Secures the washer's inner basket to the drive hub, keeping the tub centered and stable during spin. Replace if cracked, corroded, or bolts are damaged.