Kenmore Dishwasher 587.15193400 (58715193400, 587 15193400) Parts

The Door Spring Linkage is an OEM part for Frigidaire dishwashers. This part connects the door springs to the dishwasher door, ensuring smooth and balanced opening and closing of the door.

Causes of a bad door spring linkage can include wear and tear from frequent use, physical damage from impacts or mishandling, or deterioration over time.

Symptoms of a bad door spring linkage include:

• The dishwasher door not staying open or closed
• Difficulty in opening or closing the door
• A loose or sagging door
• Unusual noises when operating the door

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The High Limit Thermostat is an OEM replacement part for Frigidaire dishwashers. It is a temperature control device located in the dishwasher's heating assembly that monitors water temperature levels during cycles. 

The high-limit thermostat plays a crucial safety role by automatically shutting off the dishwasher's heating element if water temperatures get too hot, preventing potential burns or damage. It ensures the dishwasher maintains the proper temperatures required for effective cleaning.

Symptoms of a bad high-limit thermostat include: 

• Incomplete or ineffective cleaning even on short cycles  
• Lack of hot water or intermittent hot water during cycles
• Strange smells or visible steam emitting from the dishwasher
• The heating element fails to activate when needed

This OEM Frigidaire replacement part is also compatible with some Electrolux, Westinghouse, and Kenmore dishwasher models. 

This replacement bracket secures a component to the appliance frame, keeping it aligned and stable during operation. Install it to replace a bent, cracked, or missing bracket and restore a solid, rattle-free mount.

• Provides a rigid mounting point to hold the specified part in place
• Helps maintain alignment to reduce vibration, rubbing, or noise
• Replaces damaged or corroded hardware to restore a secure fit
• Common symptoms: loose or sagging component, unusual vibration/noise, or part shifting out of position

• Disconnect power before servicing; shut off water supply if working near water lines
• Note original orientation and fastener locations; take a reference photo
• Transfer and reuse existing screws/clips as needed; tighten fasteners evenly without over-torquing
• Verify alignment and test operation before final reassembly

The Dishrack Roller is an OEM part for Frigidaire dishwashers. This part ensures smooth and effortless movement of the dishrack in and out of the dishwasher. These rollers are attached to the sides of the dishrack, ensuring that it can glide easily without sticking or jamming, thus preventing damage to the dishes or the dishwasher itself.  

Causes of a bad Dishrack Roller can include wear and tear from regular use, damage from overloading the dishrack, or degradation of the roller material over time.  

Symptoms of a bad Dishrack Roller include:

• The dishrack sticking or struggling to move in and out
• A noisy operation when pulling the dishrack
• The dishrack tilting or becoming unaligned due to a missing or broken roller

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Includes one sprayarm.

Set of 8 screws and washers.

The Insulation is an OEM part for Frigidaire dishwashers. It is designed to reduce sound during wash cycles and help create a quieter dishwasher experience. The sound insulation minimizes noise transmission by absorbing and dampening vibrations throughout washing.

Causes of bad sound insulation can include breakdown of insulating materials over time, compression that reduces soundproofing density, or water damage or impacts.

Symptoms of bad sound insulation include:

• Noticeably louder operations with minimal sound dampening
• Rattling, banging, or buzzing sounds emanating from the appliance
• Transference of vibrations that causes adjacent cabinets to resonate

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Includes motor, two o-rings and wire harness.

This sump gasket seals the connection between the dishwasher tub and the sump/pump assembly. Replacing a flattened or cracked gasket restores a watertight barrier to help stop leaks from the base and protect floors and cabinetry.

• Creates a seal between the tub and sump to contain wash water
• Helps prevent leaks during fill, wash, and drain cycles
• Replace if the gasket is cracked, brittle, deformed, or compressed
• Common symptoms: water under the dishwasher, dripping from the base, moisture around the toe-kick

• Disconnect power and shut off the water supply; pull the dishwasher out if needed for access
• Access the sump area (often by removing the lower rack, spray arm, and filters); note gasket orientation
• Clean mating surfaces; seat the gasket evenly without twists. Do not use sealants unless specified by the manufacturer
• Reassemble and run a short test cycle while inspecting for leaks

Used on the upper rack track

This thermostat retainer is the mounting clip that keeps the dishwasher's thermostat secured to its base or bracket. Proper retention helps maintain accurate temperature sensing and consistent heater safety through the wash and dry portions of the cycle. What it does:

• Holds the thermostat firmly in place on the base or mounting bracket
• Prevents the thermostat from shifting, vibrating loose, or falling out of position
• Supports accurate temperature sensing and overheat protection
• Common signs of a bad/missing retainer: broken or warped clip, thermostat hanging loose, intermittent heat/drying performance

• 1 thermostat retainer

• Disconnect power and shut off water before servicing
• Remove the lower access/toe-kick panel to reach the thermostat area
• Note the thermostat's orientation; transfer it to the new retainer and snap/secure the retainer to the existing mount/hardware
• Ensure the thermostat is fully seated and wiring is routed clear of sharp edges and hot/moving components

This short connector hose links internal dishwasher plumbing to move water securely between components. Replacing a worn or cracked hose helps prevent leaks and keeps cycles running reliably. What it does:

• Routes water between two internal connection points during the wash cycle
• Helps maintain a watertight seal when properly clamped
• Common symptoms: water leaking beneath the unit, dampness around hose joints, visible cracks/hardening, or a loose fit
• Aging hoses can stiffen and drip at barbed fittings

• 1 connector hose

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick and pull the dishwasher forward as needed to access the hose
• Expect a small amount of residual water; have towels or a shallow pan ready
• Fully seat the hose on fittings, secure with appropriate clamps, then run a brief cycle and check for leaks

Black

This is the screw used to secure the dishwasher spray arm assembly components together, helping keep the arm properly attached so it can rotate and distribute wash water effectively.

• Fastens the spray arm assembly components to prevent wobble or detachment
• A loose or missing screw can cause poor cleaning, noisy operation, or a spray arm that falls off
• Restores stable spray arm rotation and consistent wash coverage

• Disconnect power and shut off water before servicing
• Open the dishwasher, remove the lower rack, and support the spray arm to prevent damage
• Use the correct screwdriver and avoid overtightening to protect plastic parts
• Check spray arm for free rotation after installation

This small check ball helps control water flow inside the refrigerator's water/ice system to prevent backflow and ensure proper filling. It restores reliable water seating where valves or distributor ports use a ball-style check. What it does:

• Acts as a one-way seal to stop water from flowing backward into the supply line or valve bore
• Helps the ice maker and dispenser fill correctly by allowing water in but not back out
• Common symptom: intermittent or incomplete ice maker fills
• Common symptom: slow or continuous dripping from dispenser or valve area

• Shut off water supply and unplug the appliance before starting
• Small part — handle carefully and note orientation/seat before removal
• Inspect valve bores and seals for debris; clean area before installing new check ball

This replacement screw secures appliance panels and internal components so they stay aligned and rattle-free. Replace missing or stripped hardware to restore a tight, reliable fit and prevent looseness that can lead to noise or damage.

• Fastens panels, brackets, or components to the chassis as designed
• Helps reduce vibration, rattling, and gaps from loose or missing hardware
• Restores proper alignment when an original screw is lost or threads are damaged
• Maintains safe, secure mounting of the original assembly

• Disconnect power (and shut off gas/water if applicable) before servicing
• Replace in the same location and orientation as the original hardware
• Hand-start threads to avoid cross-threading; tighten snugly without overtightening
• Transfer any original washer or clip if present