Kenmore Refrigerator 596.79553010 (59679553010, 596 79553010) Parts

Ice stripper removes ice cubes from the ice maker mold so the dispenser or storage bin fills properly. Replacing a worn or broken stripper helps the ice maker eject cubes cleanly and reduces ice jams or stuck cubes. What it does:

• Pushes or guides harvested cubes out of the ice mold into the bin during the ice maker's harvest cycle.
• Prevents cubes from sticking in the mold; a damaged stripper can cause incomplete ejection or leftover ice in the mold.
• Works with the ice maker's ejector mechanism to maintain consistent cube release and storage.
• A faulty or broken stripper may lead to noisy operation, partial fills, or visible ice build-up in the mold.

• Disconnect power to the appliance before starting any repair to avoid electrical shock.
• Remove the ice maker or access panel per the manufacturer's instructions to reach the stripper; keep small parts and screws organized.
• Inspect the ice mold and surrounding components for damage or ice build-up; clear ice before installing the new stripper.
• After installation, restore power and run a test harvest cycle to ensure proper cube ejection.

Supports and guides your refrigerator's drawer for smooth, aligned travel. Replace if drawer sticks, sags, or derails. Verify fit with your model number.

Factory screw that secures panels, brackets, and hardware inside your refrigerator. Replace missing or stripped screws to eliminate rattles and loose fits.

Replace your refrigerator door gasket to restore an airtight seal, maintain temperature, and reduce frost buildup. Confirm fit with your model number.

This limit switch is a temperature safety device that opens the circuit if heat rises too high. Replacing a weak or failed switch restores proper overheat protection and can resolve nuisance shutdowns or no-heat conditions due to an open safety. What it does:

• Monitors temperature at its mounting location
• Opens the electrical circuit at a preset over-temperature to stop heating or operation
• Helps protect internal components and wiring from heat damage
• Common symptoms include: won't heat, shuts off during use, or no power after an overheat event

• 1 limit switch

• Disconnect power (and gas, if applicable) before servicing
• Access the switch, note wire positions, and transfer wires one at a time
• Mount the switch flat and firmly against the original sensing surface or bracket
• After replacement, check for root causes of overheating (blocked airflow, failed fan, dirty filters, shorted element)

Fixes blank displays, unresponsive controls, or erratic cooling cycles. This control board directs refrigerator power and responds to user commands.

Replacement roller axle support shaft for refrigerators. Installs to support rotating assemblies. Replace when worn, damaged, or causing wobble.

Control knob broken, cracked, or won't turn? This replacement knob restores precise temperature and setting adjustments. Clips into place in minutes.

Water pooling in freezer or fridge? A clogged or cracked defrost drain funnel causes leaks. DIY fix in 30-45 minutes by accessing the rear freezer panel.

Ice maker not filling or leaking? This water tube routes water from the inlet to the ice maker fill valve. Replaces cracked or clogged tubing in your fridge.

Size: 8 x 1-1/4 inch.

This is a trim piece that serves as a guide for the refrigerator door flapper or breaker strip, helping to direct airflow and ensure a proper seal between compartments. It mounts near the door opening and keeps the flapper aligned correctly. Replace this part if the guide is cracked, broken, or missing, which can lead to cold air escaping and temperature inconsistencies inside the refrigerator.

Replacement divider for refrigerator pantry or deli drawer. Separates foods and prevents shifting. Essential when original is cracked, broken, or missing.

Plastic cover that protects and supports the damper assembly in your refrigerator. Replace if cracked, broken, or missing to keep airflow components secure.

This user interface control board manages the oven's front-panel display and touch controls so you can select functions, set temperatures and start cycles. Replacing a failed UI board restores normal control and display feedback. What it does:

• Receives and processes inputs from the touchpad or buttons so selections start the correct cycles
• Drives the front-panel display and indicator lights for cycle status and settings
• Communicates commands to the main control to trigger heating and timing operations
• Fault symptom coverage: blank or unresponsive display, unresponsive touchpad/buttons, or incorrect front-panel behavior

• One user interface control board

• Disconnect power at the breaker before starting any repair to prevent shock
• Handle the board by edges and avoid touching components; observe anti-static precautions
• Verify connectors are fully seated but do not force; match connector shapes and pin counts

Creates a watertight seal at water connections to prevent leaks. Replace when cracked, flattened, or worn. Confirm fit with your model number.