Kenmore Dishwasher 665.13043K110 (66513043K110, 665 13043K110) Parts

This tab-sump mounting secures the dishwasher sump/dispenser area so detergent tabs and related components stay properly aligned. Replacing a worn or broken mounting restores correct dispenser positioning and helps prevent tabs from falling loose during cycles. What it does:

• Holds the tab/sump assembly in place to maintain proper detergent tab positioning
• Prevents the dispenser or sump from shifting or sagging during operation
• Helps reduce incidents of tabs dislodging or failing to stay seated
• Supports correct alignment of adjacent dispenser components

• Disconnect power and water supply before starting any repair
• Remove the door panel or access cover to reach the sump area
• Inspect surrounding clips and seals; replace any damaged fasteners for a secure fit

Replacement wheel leg assembly for dishwashers. Restores mobility and stable support when original leg is cracked, broken, or worn. Snaps into groove.

Fix a broken or missing dishwasher detergent dispenser cover. This shield protects the dispenser assembly and restores a finished look to your unit.

This is a deflector shield mounted inside the dishwasher that directs water spray or steam away from sensitive areas such as the vent or door components. It helps protect the door latch, electronics, or surrounding cabinetry from heat and moisture damage. Replace this part if it is cracked, warped, or missing, which can lead to steam damage on your countertop or surrounding surfaces.

This kit includes hose clamps and fasteners used during dishwasher installation to secure the drain hose and water supply connections. It ensures tight, leak-free connections between the dishwasher and household plumbing. Replace this kit if you notice water leaking at hose connections or if clamps are corroded, broken, or missing during a new installation or reinstallation.

Routes water to spray arms and wash chambers inside your dishwasher. Replace if worn, cracked, or leaking to restore proper water distribution.

This handle pocket is the small insert that finishes the end of select appliance door handles and retains the KM 2.5-inch medallion. Replace a cracked or missing pocket to restore a secure hold and a clean, factory look.

• Retains the KM 2.5-in medallion at the handle end
• Provides a finished appearance and helps cover internal fasteners
• Helps keep the handle end secure to reduce looseness or rattles
• Typical symptoms: loose or missing medallion, cracked pocket, damaged/unfinished handle end

• Disconnect power to the appliance before servicing
• Access the handle end; remove any set screw(s) or trim as required
• Seat the new pocket, transfer the existing medallion, and resecure hardware
• Do not overtighten fasteners; verify the handle is secure and aligned

The Thermostat Clip is an OEM part for Whirlpool dishwashers. It plays an important supporting role by securely fastening the thermostat sensor inside the wash chamber. 

Symptoms of a faulty Thermostat Clip can include:

• Fluctuating or inconsistent water temperatures between cycles 
• Inability to properly detect temperature for desired heat levels
• Longer cycle times needed for reaching required temperatures
• Strange sounds or condensation around thermostat connection

Causes could arise from typical wear and tear stresses weakening plastic retaining clips. Exposure to harsh detergents may also erode clip material integrity over time.

This OEM replacement part is compatible with KitchenAid, Jenn-Air, Kenmore, and select Hotpoint and Roper dishwasher models as well. 

Shield for dishwashers. Protects internal components from water and debris. Replace if cracked, broken, or missing to maintain proper coverage.

Dispenser won't latch or close? This detergent dispenser releases soap at the right time. Moderate DIY repair requiring inner door panel removal.

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

Dishwasher won't start or lights flashing? The electronic control board manages cycles and timing. Moderate DIY repair restores full operation.

Fix intermittent power issues or loose connections in your dishwasher. This wire connector restores secure electrical contact between components.

Filters debris from water to protect pump and spray arms. Replace if you notice slow drainage, poor cleaning, or water left in tub. Verify fit by model.