Kenmore Dishwasher 665.13429K701 (66513429K701, 665 13429K701) Parts

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This pump and motor assembly replaces the dishwasher's pump to restore proper water circulation and draining. It helps clear standing water and maintain wash performance when the original unit is worn or leaking. What it does:

• Drives water flow for normal wash cycles and pumps wastewater out during drain
• Restores proper draining when the dishwasher leaves water in the tub
• Reduces or eliminates grinding, humming, or squealing noises caused by a failing pump motor
• Helps resolve common drain-related error codes and poor wash results tied to low circulation

• One pump and motor assembly

• Disconnect power and water supply before beginning any repair
• Expect residual water in the tub and hoses; have towels or a pan ready
• Handle electrical connectors and hoses gently; replace any damaged clamps or seals
• Test the dishwasher on a short cycle after installation to ensure proper drain and flow

Size: 8-32 x 1/2 inch.

This is the rear wheel support for a dishwasher rack. It helps guide and support the rack as it slides in and out, restoring smooth movement and preventing the rack from binding or derailing.

• Supports and guides the rack at the rear during opening/closing
• Helps correct issues like a wobbly, sticking, or misaligned rack
• Can address noisy, rough rack travel caused by a worn support
• Maintains proper rack tracking to reduce derailment

• Disconnect power and water before servicing
• Pull rack forward to access the rear support area
• Depress locking tabs/retainer to remove the old support; press-fit the new support until secure
• Verify smooth rack travel before returning the appliance to service

This positioner aligns and secures its mating component in the correct location inside your appliance. Replacing a cracked, worn, or missing positioner restores proper fit so the assembly stays put and operates as designed.

• Holds the related part in the proper position and orientation
• Prevents shifting, sagging, or rattling during use
• Supports smooth adjustment or movement where applicable
• Common symptoms: loose or misaligned component, difficulty adjusting or seating the piece, visible cracks, or a missing clip

• Disconnect power; also shut off gas or water if your appliance uses these utilities
• Note the original orientation and take photos before removal
• Transfer any reused hardware and fully seat tabs/slots to avoid damage
• Wear cut-resistant gloves and check alignment after reassembly

This replacement lever operates the overflow/level switch assembly to help the washer detect and respond to water level changes. It restores the mechanical action that tells the control when the tub is full. What it does:

• Moves the overflow/level switch mechanism so the machine can sense water level correctly
• Helps address overfilling, continuous filling, or erratic fill behavior caused by a worn or broken lever
• Restores reliable engagement between the float/actuator and the switch
• Works as the mechanical linkage for the overflow/level sensing assembly

• Disconnect power and turn off the water supply before beginning service.
• Access typically requires removing the cabinet or control console; keep fasteners organized.
• Install the lever so it aligns with the switch actuator and float linkage; verify smooth movement after assembly.

This tab-sump mounting secures the dishwasher sump/dispenser area so detergent tabs and related components stay properly aligned. Replacing a worn or broken mounting restores correct dispenser positioning and helps prevent tabs from falling loose during cycles. What it does:

• Holds the tab/sump assembly in place to maintain proper detergent tab positioning
• Prevents the dispenser or sump from shifting or sagging during operation
• Helps reduce incidents of tabs dislodging or failing to stay seated
• Supports correct alignment of adjacent dispenser components

• Disconnect power and water supply before starting any repair
• Remove the door panel or access cover to reach the sump area
• Inspect surrounding clips and seals; replace any damaged fasteners for a secure fit

This cover is a factory replacement access panel that protects internal components and restores the appliance's finished appearance. It keeps wiring and controls shielded from dust and accidental contact for safer, longer-lasting operation. What it does:

• Shields internal wiring, controls, and components from dust, debris and accidental contact
• Keeps small parts and fasteners secured inside the appliance cabinet
• Restores the appliance's finished exterior where the original cover was damaged or missing
• Helps maintain proper airflow routing and component spacing when installed correctly

• Disconnect power to the appliance before beginning any service to avoid shock or injury.
• Verify the cover orientation and fastener locations before securing; use OEM screws where specified.
• Handle with care to avoid scratching or bending the cover; ensure tabs snap fully into place.
• Inspect for damage and secure any loose parts before installing the cover.

For complete door balance link kit order 8194001

This thermostat bracket holds the oven or range thermostat securely in place, ensuring accurate temperature sensing and stable oven performance. Replaces a worn or broken bracket to restore proper thermostat positioning. What it does:

• Secures the thermostat assembly to the oven/range interior so the thermostat bulb or probe senses temperature correctly
• Prevents the thermostat from shifting or contacting heating elements
• Commonly replaced when the bracket is cracked, bent, or missing and causes temperature or control issues
• Helps reduce temperature inconsistencies caused by a loose or damaged mounting

• Disconnect power to the appliance before servicing to avoid electrical shock or injury
• Handle the thermostat and sensor bulb carefully; avoid kinks or direct pressure on sensing elements
• Basic hand tools are typically required; verify part alignment before tightening fasteners

This dispenser cover (shield) replaces the plastic trim that surrounds a refrigerator's dispenser opening, restoring a clean finished look and helping direct water or ice into your cup. Fits where the dispenser meets the cabinet face. What it does:

• Covers and protects the dispenser opening, preventing chips and cosmetic damage
• Helps guide water and ice into cups for more accurate dispensing
• Hides internal dispenser components for a finished appearance
• Can reduce direct contact with moving dispenser parts

• One dispenser cover (shield)

• Remove power to the appliance before servicing to avoid electrical or injury risk
• Typically installs by snapping into place or fastening with a few screws; keep hardware if reusing
• Inspect surrounding trim for damage and replace any broken clips or screws for a secure fit

This loose bag assembly is a direct-fit replacement designed to restore the original containment or collection function in compatible Whirlpool appliances. It provides a simple swap to fix a damaged or missing bag and keep the appliance operating as intended. What it does:

• Replaces a worn, torn, or missing bag used for containment or collection in the appliance
• Restores proper collection and helps prevent debris or material from escaping into the appliance cavity
• Helps reduce related performance issues that occur when the bag is damaged or absent
• Matches OEM form and fit for an easy, reliable replacement

• One loose bag assembly as shown

• Turn off and unplug the appliance before attempting replacement
• Remove any panels or components required to access the bag
• Install the bag in the correct orientation and secure all fasteners or clips
• Inspect surrounding seals and openings; replace any damaged parts to ensure proper operation

This adjuster is a replacement door/hinge adjustment component that restores proper door alignment and closing action for compatible appliances. It helps re-establish correct clearance and reduces rubbing, binding, or uneven gaps. What it does:

• Provides the adjustment point for proper door alignment and smooth operation
• Helps correct doors that sit unevenly, rub, or don't seal consistently
• Restores the ability to fine-tune door position after hinge or cabinet repairs
• Reduces noise and wear caused by misaligned doors or panels

• One adjuster as shown

• Turn power off and disconnect the appliance before starting any repair
• Some disassembly of the door, hinge, or trim may be required
• Keep fasteners and small parts organized; verify orientation before final tightening

This silverware basket replaces a cracked, broken, or missing utensil holder to keep forks, knives and spoons organized during the wash cycle. It fits into the dishwasher's lower rack and helps maintain cleaning efficiency. What it does

• Holds and separates silverware and small utensils so water and detergent can reach each piece
• Prevents nesting and keeps items upright for better cleaning and drying
• Secures loose items during the wash to avoid damage to dishes or the dishwasher
• Works with standard lower-rack mounting locations on compatible dishwashers

• One silverware basket

• Installs in the lower dishwasher rack; no tools required for typical replacements
• Position tines or compartments so utensils sit upright and do not block spray arms
• Do not overload the basket; bent or damaged tines may affect fit and function

This console assembly replaces the dryer control panel and restores user controls and display functions so you can select cycles and monitor status. It's a direct-fit service assembly for affected Whirlpool-brand dryers. What it does

• Houses the control board, user buttons, and display used to select cycles and options
• Restores unresponsive or damaged buttons, cracked panels, or missing display components
• Re-establishes a secure mounting surface for the appliance controls and user interface
• Helps resolve symptoms like non-working buttons, blank or damaged console, or loose control hardware

• One complete console assembly (control panel) as shown

• Disconnect power (unplug or switch off breaker) before starting any repair
• Some wiring harnesses and fasteners may need careful removal; label connectors as needed
• Handle the assembly gently to avoid cracking plastic or damaging the display and connectors