Kenmore Dishwasher 665.15825691 (66515825691, 665 15825691) Parts

• Not drying dishes properly

My Whirlpool dishwasher (wdf520padm3) started leaving food on dishes and not drying dishes as well as it used to, even when I ran the 'high temp' and 'heavy' cleaning options. This started happening after about 3 years of operation. To try to diagnose the issue, I started the diagnostics cycle (see below for instructions on how to do this). However, the 'Clean' LED is also not working on my dishwasher, so I was unable to read the error code after the service cycle finished. I decided to... Read more

• Leaking

I thought it was the gasket so I ordered a new one. While waiting for it to arrive I read some other forums where I read that sometimes the air vent on the front could be dirty and cause leaking. I popped out that vent cover and it was clogged. Using an old toothbrush and a tiny paint brush I cleaned all of the gunk out. No more leak even with the old gasket in place. I'll save the new gasket for when I need it in the future. Read more

• Not drying dishes properly

Replaced heater element: Once I had the dishwasher out of the cabinet with supply hose, drain hose and electric disconnected, removing the heater element was fast and easy. However, it was confusing that the new heater element had rubber washers on it already, something not mentioned in the product listing, although kinda visible in the photo. I ordered the separate rubber washer parts recommended by Appliance Parts Pros together with the heater element. The separate rubber washers were the... Read more

• Noisy
• Will not drain

I had previously disassemble the pump assembly to find what I at first thought was an oddly shaped spring, which it was. What I learned by researching the parts was that the spring's odd shape was a result of something having gotten caught in the pump and jamming the impeller. After ordering the parts, I watched the "repair video" a few time and proceeded to remove and replaced the affected parts. Reassembly went pretty much as described with the one small glitch being the seating of the new... Read more

Just replaced the things. Had to reuse old tine rows, rollers, the spray arm, etc., i.e. I removed 'em from the old racks and put on the new ones, but that was piece of cake. Also, I cleaned the food grinder and the discharge valve compartment (thank you very ???? ???? much, Internet), so spray arms around the top rack get enough water pressure now. I didn't have to buy any parts for the latter part of this little repair project, though. Read more

• Not cleaning dishes properly

Replaced upper and lower spray arms, plus nylon bearings. Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

• Will not fill with water

Ordered new inlet water valve and float switch kit. After repairs it now works fine. However the water inlet valve outlet end for fill hose (not water source) and wire connections (supposedly for this unit) were oriented 180 degrees opposite. I had to gently remove the blue plastic valve off the metal support bracket and turn it around and press back in place. Fortunately it appears it was designed for either orientation. Also the solenoid had to be unclipped and also rotated. Again it was... Read more

Touch up paint Read more

• Will not stop filling with water
• Leaking

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

Dishwasher washer would not drain after hearing glass-like particles during the drain cycle despite trying to clean the cylinder filter. Originally suspected the drain motor was damaged. After watching a video on how to replace the drain pump, I carefully energized the dishwasher (from water and electricity) then removed the dishwasher to take a look. After removal of drain hose from the pump, discovered that drain hose was connected to water inlet assembly which also needed removal to... Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more

Appeared to be two problems: the latch was worn and one of the pins that slid in a guide on the actuator located in the inner panel had broke off. Detergent lid spring and pin appeared to be OK but decided to replace since I was aready working on it. I ordered all the inner panel mechanism from the control arm to the latch actuator on the inner panel. The repair was successful as the detergent dispenser now opens during its cycle. Read more